Bedienungsanleitung Hikoki H60MEY (Seite 11 von 120) (Alle Sprachen)

816280

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

English

ABOUT THE PROTECTION

FUNCTION

This tool has a built-in protection circuit for preventing

damage to the unit in the event of an abnormality. Depending

on the nature of the abnormality, the display lamp will ﬂ ash

as shown in Table 1 and the unit will cease to operate. In

such cases, verify the problem indicated by the ﬂ ashing and

take whatever steps are necessary to correct the problem.

NOTE

Repair may be required if the display lamp continues to

ﬂ ash after taking all necessary steps to correct the problem.

If the problem persists, please arrange for repairs.

Table 1

Display

lamp

ﬂ ashing Cause Solution

Flash

Internal temperature

has risen beyond

the unit’s speciﬁ ed

temperature.

(Temperature

increase protection

function)

Turn oﬀ the unit

and allow it to cool

down for about 15 to

30 minutes.

When the temperature

goes down, press the

impact rate selector

switch to recover.

Flash Excessive pressure

applied to the tool

has resulted in an

overload.

(Overload

protection function)

Press the impact rate

selector switch to

recover. Try to avoid

tasks that will apply

excess pressure to

the unit.

Flash

Tool is connected

to a power source

whose voltage is

either too high or

too low.

(Circuit protection

function)

Connect the unit to a

power supply matching

the input voltage

speciﬁ ed on the

nameplate. Press the

impact rate selector

switch to recover.

Flash Sensor signal read

error.

(Control monitoring

function)

Press the impact rate

selector switch to

recover. Repair may

be required if this error

continuously occurs.

GREASE REPLACEMENT

This Demolition Hammer is of full air-tight construction to

protect against dust and to prevent lubricant leakage.

Therefore, this Demolition Hammer can be used without

lubrication for long periods. Replace the grease as described

below.

Grease Replacement Period

After purchase, replace grease after every 6 months of

usage. Ask for grease replacement at the nearest authorized

Service Center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident.

1. Inspecting the tool

Since use of a dull tool will cause motor malfunctioning

and degraded eﬃ ciency, replace the tool with new ones

or resharpen them without delay when abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

000BookH60ME.indb11000BookH60ME.indb11 2022/10/3117:11:052022/10/3117:11:05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki H60MEY Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info