Bedienungsanleitung Hikoki M12VE (Seite 7 von 100) (Alle Sprachen)

816317

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If the

plug is connected to a receptacle while the power switch

is in the ON position, the power tool will start operating

immediately, which could cause a serious accident.

3. Extension cord

When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

4. Setting the attachment angle of the handle

As Fig. 1 shows, the handle attachment angle can be set

in three stages. Use a plus head screwdriver to loosen the

machine screw attached to the handle, adjust the handle

to the desired position and retighten the machine screw.

5. RCD

The use of a residual current device with a rated residual

current of 30 mA or less at all times is recommended.

INSTALLING AND REMOVING BITS

WARNING

Be sure to switch power OFF and disconnect the plug

from the receptacle to avoid serious trouble.

1. Installing bits

(1) Clean and insert shank of bit into the collet chuck until

shank bottoms, then back it out approximately 2 mm.

(2) With the bit inserted and pressing the lock pin holding

the armature shaft, use the 23 mm wrench to ﬁ rmly

tighten the collet chunk in a clockwise direction (viewed

from under the router). (Fig. 2)

CAUTION

○ Ensure that the collet chuck is ﬁ rmly tightened after

inserting a bit. Failure to do so will result in damage to

the collet chuck.

○ Ensure that the lock pin is not inserted into the armature

shaft after tightening the collet chuck. Failure to do so

will result in damage to the collet chuck, lock pin and

armature shaft.

(3) When using the 8 mm or 1/4" diameter shank bit, replace

the equipped collet chuck with the one for 8 mm or 1/4"

diameter shank bit which is provided as the optional

accessory.

2. Removing Bits

When removing the bits, do so by following the steps for

installing bits in reverse order. (Fig. 3)

CAUTION

Ensure that the lock pin is not inserted into the armature

shaft after tightening the collet chuck. Failure to do so

will result in damage to the collet chuck, lock pin and

armature shaft.

HOW TO USE THE ROUTER

1. Adjusting depth of cut (Fig. 4)

(1) Use stopper pole to adjust depth of cut.

Place the tool on a ﬂ at wood surface.

Turn the stopper block so that section to which the cutting

depth setting screw on a stopper block is not attached

comes to the bottom of the stopper pole. Loosen wing bolt

allowing the stopper pole to contact with stopper block.

Loosen the lock lever and press the tool body until the bit

just touches the ﬂ at surface. Tighten the lock lever at this

point. (Fig. 5)

Tighten wing bolt. Align the depth indicator with the “0”

graduation of scale.

Loosen wing bolt, and raise until indicator aligns with

the graduation representing the desired cutting depth.

Tighten wing bolt.

Loosen the lock lever and press the tool body down until

the stopper block to obtain the desired cutting depth.

(2) As shown in Fig. 6 (a), loosening the two nuts on the

threaded column and moving then down will allow you to

move down to the end position of the bit when the lock

lever is loosened. This is helpful when moving the router

to align the bit with the cutting position.

As shown in Fig. 6 (b), tighten the upper and lower nuts

to secure the cutting depth.

(3) When you are not using the scale to set the cutting depth,

push up the stopper pole so that it is not in the way.

2. Stopper block (Fig. 7)

The 2 cut-depth setting screws attached to the stopper

block can be adjusted to simultaneously set 3 diﬀ erent

cutting depth. Use a wrench to tighten the nuts so that the

cut-depth setting screws do not come loose at this time.

3. Guiding the router

WARNING

Be sure to switch power OFF and disconnect the plug

from the receptacle to avoid serious trouble.

(1) Template Guide

Use the template guide when employing a template

for producing a large quantity of identiﬁ cally shaped

products.

As shown in Fig. 8, secure the template guide to the

base of the router with two accessory screws. At this

time, ensure that the projection side of the template

guide is facing the bottom surface of the base of the

router.

A template is a proﬁ ling mold made of plywood or thin

lumber.

When making a template, pay particular attention to the

matters described bellow and illustrated in Fig. 9.

When using the router along the interior plane of the

template, the dimensions of the ﬁ nished product will be

less than the dimensions of the template by a amount

equal to dimension “A”, the diﬀ erence between the

radius of the template guide and the radius of the bit. The

reverse is true when using the router along the exterior of

the template.

Secure the template to the workpiece. Feed the router

in the manner that the template guide moves along the

template as shown in Fig. 10.

(2) Parallel guide (Fig. 11)

Use parallel guide for chamfering and groove cutting

along the materials side.

Insert the guide bar into the hole in the base, adjust the

distance between the bit and the guide surface, and then

ﬁ rmly tighten the wing bolt (A).

As shown in Fig. 12, securely attach the bottom of the

base to processed surface of the materials. Feed the

router while keeping the guide plane on the surface of

the materials.

4. Adjusting the rotation speed

The M12VE has an electronic control system that allows

stepless rpm changes.

As shown in Fig. 13, dial position “1” is for minimum

speed, and position “6” for maximum speed.

5. Cutting

CAUTION

○ Wear eye protection when operating this tool.

○ Keep your hands, face and other body parts away from

the bits and any other rotating parts, while operating the

tool.

00BookM12VE.indb700BookM12VE.indb7 2022/12/2211:28:102022/12/2211:28:10

Hikoki M12VE Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info