Bedienungsanleitung Hikoki M3612DA (Seite 15 von 280) (Alle Sprachen)

816267

Zoom out

Zoom in

Vorherige Seite

1/280

Nächste Seite

English

A template is a proﬁ ling mold made of plywood or thin

lumber.

When making a template, pay particular attention to the

matters described bellow and illustrated in Fig. 12.

When using the router along the interior plane of the

template, the dimensions of the ﬁ nished product will be

less than the dimensions of the template by a amount

equal to dimension “A”, the diﬀ erence between the

radius of the template guide and the radius of the bit. The

reverse is true when using the router along the exterior of

the template.

Secure the template to the workpiece. Feed the router

in the manner that the template guide moves along the

template as shown in Fig. 13.

(2) Straight guide (Standard accessory) (Fig. 14)

Use straight guide for chamfering and groove cutting

along the materials side.

Insert the guide bar into the hole in the bar holder, then

lightly tighten the 2 wing bolts (A) on top of the bar

holder.

Insert the guide bar into the hole in the base, then ﬁ rmly

tighten the wing bolt (A).

Make minute adjustments of the dimensions between

the bit and the guide surface with the feed screw, then

ﬁ rmly tighten the 2 wing bolts (A) on top of the bar holder

and the wing bolt (B) that secures the straight guide.

As shown in Fig. 15, securely attach the bottom of the

base to processed surface of the materials. Feed the

router while keeping the guide plane on the surface of

the materials.

4. Switch operation

This product is equipped with an ON/OFF Lock button

to prevent any inadvertent switch trigger operation. To

activate the tool, press down on the ON/OFF Lock button

and draw the switch trigger. (Fig. 16)

When the switch trigger is fully drawn, a further press

of the ON/OFF Lock button will lock the switch trigger

in place, allowing the release of the switch trigger for

continued operation. (Fig. 17 (a))

The switch trigger will not be locked if the ON/OFF Lock

button is released before the switch trigger is fully drawn,

making it possible to operate the tool with a press of the

switch trigger.

To unlock the switch trigger, draw the switch trigger

once again to release the ON/OFF Lock button and

discontinue operation. (Fig. 17 (b))

Prior to using the tool, make sure that the ON/OFF Lock

button and the switch trigger are operating properly.

5. How to use the LED light (Fig. 18)

The LED light will light the area at the tip of the tool when

the switch is “ON”.

The LED light will automatically power oﬀ 10 seconds

after the switch is released.

6. Adjusting the rotation speed

The M3612DA has an electronic control system that

allows rpm changes.

As shown in Fig. 19, dial position “1” is for minimum

speed, and position “6” for maximum speed.

7. Cutting

CAUTION

○ Wear eye protection when operating this tool.

○ Keep your hands, face and other body parts away from

the bits and any other rotating parts, while operating the

tool.

NOTE

○ Do not press the lock pin while the motor is rotating.

Also, do not switch the tool on while pressing the lock

pin.

Doing so may damage the lock pin and/or shaft as well

as result in injury.

○ Please limit the cutting depth of a single cut to under

20 mm.

○ When cutting a deep groove, repeat the cut 2 or 3 times.

Deep cutting operations can make the tool diﬃ cult

to control and may overload the motor, resulting in

malfunction.

○ Moving the tool forward fast may cause a poor quality

of cut, or damage to the bit or motor. Moving the tool

forward too slowly may burn and mar the cut.

The proper feed rate will depend on the bit size, the kind

of workpiece and depth of cut. Before beginning the cut

on the actual workpiece, it is advisable to make a sample

cut on a piece of scrap lumber. This will show exactly

how the cut will look as well as enable you to check

dimensions.

○ Abnormalities and overloads will trigger the overload

protector, and stop operation. Remove the load

immediately, and turn the power oﬀ , then on. The

rotation speed should return to normal.

(1) As shown in Fig. 20, remove the bit from the work pieces

and press the switch lever up to the ON position. Do

not start cutting operation until the bit has reached full

rotating speed.

(2) The bit rotates clockwise (arrow direction indicated on

the base). To obtain maximum cutting eﬀ ectiveness,

feed the router in conformance with the feed directions

shown in Fig. 21.

8. Trimmer Guide (Optional accessory) (Fig. 22)

Use the trimmer guide for trimming or chamfering. Attach

the trimmer guide to the bar holder as shown in Fig. 23.

After aligning the roller to the appropriate position,

tighten the two wing bolts (A) and the other two wing

bolts (B). Use as shown in Fig. 24.

9. Dust Collector Set (Standard accessory)

Connect the dust collector set cleaner to collect dust.

(1) Mounting the dust collector.

Use a screwdriver to attach the two screws to the base.

(Fig. 25)

Align the holes on the dust collector with the two screws

and attach the dust collector.

Tighten the two knob nuts.

Connect the cleaner to the dust collector. (Fig. 26)

(2) Dismounting the dust collector.

Use a screwdriver to loosen the two screws.

LED LIGHT WARNING SIGNALS

(Fig. 30)

This product features functions that are designed to protect

the tool itself as well as the battery. When any of the

safeguard functions are triggered, any of the LED light will

blink as described in Table 3.

In this case, follow the instructions described under

corrective action.

Fig. 30

00BookM3612DA.indb1500BookM3612DA.indb15 2023/09/0722:54:222023/09/0722:54:22

Hikoki M3612DA Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info