Bedienungsanleitung Hikoki M8V2 (Seite 8 von 116) (Alle Sprachen)

816318

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

English

(2) Straight guide (Standard accessory) (Fig. 10)

Use straight guide for chamfering and groove cutting

along the materials side.

Insert the guide bar into the hole in the bar holder, then

lightly tighten the 2 wing bolts (A) on top of the bar

holder.

Insert the guide bar into the hole in the base, then ﬁ rmly

tighten the wing bolt (A).

Make minute adjustments of the dimensions between

the bit and the guide surface with the feed screw, then

ﬁ rmly tighten the 2 wing bolts (A) on top of the bar holder

and the wing bolt (B) that secures the straight guide.

As shown in Fig. 11, securely attach the bottom of the

base to processed surface of the materials. Feed the

router while keeping the guide plane on the surface of

the materials.

4. Adjusting the rotation speed

The M8V2 has an electronic control system that allows

stepless rpm changes.

As shown in Fig. 12, dial position “1” is for minimum

speed, and position “6” for maximum speed.

5. Cutting

CAUTION

○ Wear eye protection when operating this tool.

○ Keep your hands, face and other body parts away from

the bits and any other rotating parts, while operating the

tool.

(1) As shown in Fig. 13, remove the bit from the work pieces

and press the switch lever up to the ON position. Do

not start cutting operation until the bit has reached full

rotating speed.

(2) The bit rotates clockwise (arrow direction indicated on

the base). To obtain maximum cutting eﬀ ectiveness,

feed the router in conformance with the feed directions

shown in Fig. 14.

NOTE

If a worn bit is used to make deep grooves, a high

pitched cutting noise may be produced.

Replacing the worn bit with a new one will eliminate the

high pitched noise.

6 Trimmer Guide (Optional accessory) (Fig. 15)

Use the trimmer guide for trimming or chamfering. Attach

the trimmer guide to the bar holder as shown in Fig. 16.

After aligning the roller to the appropriate position,

tighten the two wing bolts (A) and the other two wing

bolts (B). Use as shown in Fig. 17.

7. Dust Collector Set

Connect the dust collector set cleaner to collect dust.

(1) Mounting the dust collector.

Use a screwdriver to attach the two screws to the base.

(Fig. 18)

Align the holes on the dust collector with the two screws

and attach the dust collector.

Tighten the two knob nuts.

Connect the cleaner to the dust collector. (Fig. 19)

(2) Dismounting the dust collector.

Use a screwdriver to loosen the two screws.

MAINTENANCE AND INSPECTION

1. Oiling

To ensure smooth vertical movement of the router,

occasionally apply a few drops of machine oil to the

sliding portions of the columns and end bracket.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI AUTHORIZED

SERVICE CENTER.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must be

returned to HiKOKI Authorized Service Center for the

cord to be replaced.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

SELECTING ACCESSORIES

The accessories of this machine are listed on page 110.

For details regarding each bit type, please contact the

HiKOKI Authorized Service Center.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: — Neutral

Brown: — Live

As the colours of the wires in the main lead of this tool may

not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal marked

with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

000BookM8V2.indb8000BookM8V2.indb8 2022/12/2211:07:532022/12/2211:07:53

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki M8V2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info