Bedienungsanleitung Hikoki N 14DSL (Seite 20 von 200) (Alle Sprachen)

742724

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

APPLICATION

○ Securing the moisture-permeable waterprooﬁ ng sheet

in position

○ Securing the heat insulation material in position

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (Fig. 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (Fig. 2).

CHARGING

Battery and battery charger are not included with this

product.

For rechargeable batteries, please charge in according

to the handling instructions of the charger which you are

using. (Fig. 3)

BEFORE USE

1. Preparing the Staples and Performing Safety

Inspections

WARNING

○ Do not use the product near ﬂ ammable liquids or

gases.

○ Do not place the product near children or other non-

qualiﬁ ed people.

○ Run a full check to make sure that no screws are loose.

○ Check to make sure that there are no damaged or

missing parts, or malfunctioning parts owing to rust,

etc.

Prepare staples that match the job at hand.

Refer to MAINTENANCE AND INSPECTION and carry

out safety inspections without fail.

2. Trigger Lock Mechanism (Fig. 4)

WARNING

Make sure the trigger is locked when not ﬁ ring staples.

This stapler has a lock mechanism to prevent the

staples from being ﬁ red.

Set the lock lever at the

position to lock the trigger.

Slide the lock lever to the

position when the stapler is

to be used, and to the

position when it is not in use.

3. Checking Push Lever Operations (Fig. 5)

WARNING

Always make sure the trigger is locked and the battery

removed from the power tool when checking push lever

operations.

Check to make sure the push lever slides smoothly

when operated.

Clean the sliding area on the push lever if it doesn’t

slide smoothly.

4. Handling the Staples

NOTE

○ Handle the staples carefully.

There are cases in which the joined staple strips may

be broken if they are dropped, and using them in this

state may result in defective staple loading, leading

to blank ﬁ ring or staple jams. Do not use joined staple

strips that are broken.

○ Do not leave the staples outdoors or in direct sunlight

for long periods of time.

Failure to observe this may result in rusting or defects

in the joined staple strips. Use the staple packaging or

other materials for storage purposes.

5. Loading the Staples (Fig. 6)

WARNING

Lock the trigger and remove the battery from the

stapler when loading or removing staples.

(1) Press the stop lever and slide the magazine backward.

(2) Place the staples in the magazine with the prongs

facing upward.

(3) Slide the magazine back into position until the stop

lever locks into place.

NOTE

○ Close the magazine gently.

Using excessive force to close the magazine may result

in the joined staple strips being deformed, preventing

the magazine from being closed.

○ Check the magazine blade guide if it won’t close

smoothly.

HOW TO USE THE CORDLESS

STAPLER

There are two ways to discharge staples: Single Shot, in

which the push lever is placed against the area where the

staple is to be ﬁ red ﬁ rst and the trigger then pulled, and

Continual Shot, in which the trigger is pulled ﬁ rst and the

push lever then placed against the relevant area.

The single-shot mode places the emphasis on ﬁ nishing

and is used to ensure that the staple is driven into the

required place, while the continual-shot mode is used to

drive in staples repeatedly with the trigger constantly being

pulled.

The power tool is equipped with a mechanism to alternate

between single-shot and continual-shot operations to

ensure that work is carried out in the most eﬃ cient way.

Safety Devices

The power tool has been designed so that staples

cannot be ﬁ red unless both the push lever and the

trigger are simultaneously operated. In other words,

staples will not be discharged when only the trigger is

pulled, or when only the push lever (discharge outlet)

is placed against the required area. This is to prevent

the staples from being discharged when the trigger is

accidentally pulled or when the push lever (discharge

outlet) is accidently placed against something.

● Single-shot Stapling (Fig. 7)

(1) Make sure the discharge outlet is ﬁ rmly placed against

the place where the staple is to be discharged.

(2) Pull the trigger to ﬁ re the staple.

(3) Withdraw the power tool and release the trigger.

NOTE

○ Use the single-shot mode to accurately staple the

required location.

○ There are cases in which subsequent stapling will not

be possible if the trigger is released halfway through

being pulled.

To correct this, remove the battery and then replace it.

● Continual-shot Stapling (Fig. 8)

First pull the trigger then place the push lever (discharge

outlet) against the required area to repeatedly ﬁ re

staples.

(1) First pull the trigger.

(2) Place the push lever (discharge outlet) against the

required area to ﬁ re the staples.

(3) Withdraw the stapler with the trigger pressed, and

then repeat procedure from step (2) to repeatedly ﬁ re

staples.

English

0000Book_N14DSL.indb 200000Book_N14DSL.indb 20 2020/04/17 14:16:222020/04/17 14:16:22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki N 14DSL Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info