Bedienungsanleitung Hikoki NT1850DA (Seite 17 von 332) (Alle Sprachen)

816326

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

English

(1) Intermittent operation (Trigger ﬁ re)

Use the SINGLE SEQUENTIAL ACTUATION

MECHANISM setting. (See Fig. 12)

WARNING

○ For intermittent operation, Set the nailing operation

switch to SINGLE SEQUENTIAL ACTUATION

MECHANISM (Nailing operation indicator is light in

blue.) (i.e. Set to SINGLE ACTUATION MECHANISM.)

○ To avoid double ﬁ ring or accidental ﬁ ring due to recoil.

1) Set to SINGLE SEQUENTIAL ACTUATION

MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

Set the nailing operation switch to SINGLE SEQUENTIAL

ACTUATION MECHANISM (Nailing operation indicator

is light in blue.)

Position the nail outlet on the workpiece with ﬁ nger oﬀ

the trigger.

Depress the push lever ﬁ rmly until it is completely

depressed.

Pull the trigger to drive a nail.

Remove ﬁ nger from the trigger and lift the tool oﬀ the

wood surface completely.

To continue nailing in a separate location, move the nailer

along the wood, repeating steps – as required.

NOTE

Operations

and should be done within 4 seconds

of each other. If more than 4 seconds pass after , the

Nailer will not work properly. If this happens, retry from

(2) Continuous operation (Push lever ﬁ re)

Using CONTACT ACTUATION MECHANISM (See

Fig. 13)

WARNING

To avoid double ﬁ ring or accidental ﬁ ring due to recoil.

1) Do not press the nailer against the wood with

excessive force.

2) Separate the nailer from the wood as it recoils after

nailing.

Set the nailing operation switch to CONTACT

ACTUATION MECHANISM (Nailing operation indicator

is blink in blue.)

Pull the trigger with the Nailer oﬀ the workpiece.

Depress the push lever against the workpiece to drive a

nail.

Move the Nailer along the workpiece with a bouncing

motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been driven,

remove ﬁ nger from the trigger.

NOTE

Operations

and should be done within 2 seconds

of each other. If more than 2 seconds pass after , the

Nailer will not work properly. If this happens, retry from

WARNING

○ Keep your ﬁ nger oﬀ the trigger except during nailing

operation, because serious injury could result if the push

lever accidentally contacts you or others in work area.

○ Keep hands and body away from the discharge area.

This HiKOKI nailer may bounce from the recoil of driving

a nail and unwanted subsequent nail may be driven,

possibly causing injury.

NOTE

○ If all warnings and instructions are followed, safe

operation is possible with all two systems: SINGLE

SEQUENTIAL ACTUATION MECHANISM, CONTACT

ACTUATION MECHANISM.

○ Always handle nails and package carefully. If nails are

dropped, collating bond may be broken, which will cause

mis-feeding and jamming.

○ After nailing:

1) remove battery from the Nailer;

2) remove all nails from the Nailer;

2. Adjusting the nailing depth

To assure that each nail penetrates to the same depth,

be sure that the Nailer is always held ﬁ rmly against the

workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

Remove the battery from the Nailer.

If nails are driven too deep, turn the adjuster to the

shallow side. (See Fig. 14)

Adjustments are in half-turn increments.

If nails are driven too shallow, turn the adjuster to the

deep side. (See Fig. 15)

Stop turning the adjuster when a suitable position is

reached for a nailing test.

Connect the battery to the Nailer.

ALWAYS WEAR SAFETY GLASSES.

Perform a nailing test.

Remove the battery from the Nailer.

Choose a suitable position for adjuster.

3. Using the hook (See Fig. 16)

WARNING

When using the hook, turn oﬀ the power switch (green

light “OFF”). Pay suﬃ cient attention so that the main

equipment does not fall.

If the tool falls, there is a risk of accident.

Hook can be installed on the left or right side.

Remove the battery, then remove all remaining nails

from the magazine.

Securely hold the main unit and remove the screw using

a screwdriver.

Remove the hook.

Install the hook on the other side and securely fasten

with screw.

NOTE

Hook can be used as a hanger.

4. Using the nose cap (See Fig. 17)

WARNING

When attaching or detaching the nose cap, be sure

to remove your ﬁ nger from the trigger and remove all

remaining fasteners and the battery from the nailer.

If you like to protect the surface of workpiece against

scratches or markings made by the push lever, attach the

accessory nose cap to the push lever.

Remove all remaining fasteners and battery from nailer.

Put the nose cap to the toe of the push lever.

When not using the nose cap, secure in the storage

compartment located on the reverse side of the

magazine.

NOTE

The nose cap may reduce nailing depth due to its

thickness. Re-adjustment of nailing depth is required.

5. Clearing a jam

If nails are jammed in ﬁ ring head, remove it, and adjust

the nailing in the following order.

CAUTION

Remove the battery from the Nailer.

Remove all nails.

Release the Lock lever and open guide plate. (See

Fig. 18)

Remove the jammed nail with a slotted-head screwdriver.

(See Fig. 19)

CAUTION

○ NEVER hit the driver blade.

○ NEVER point the tool at yourself or another person, to

avoid risk of injury by mis-ﬁ ring.

Even if the battery is removed from the nailer, there is still

energy of compressed air remaining inside.

0000BookNT1850DA.indb170000BookNT1850DA.indb17 2022/09/0814:45:002022/09/0814:45:00

Hikoki NT1850DA Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info