Bedienungsanleitung Hikoki NT1865DBAL (Seite 21 von 420) (Alle Sprachen)

816356

Zoom out

Zoom in

Vorherige Seite

1/420

Nächste Seite

English

○ To avoid double ﬁ ring or accidental ﬁ ring due to recoil.

1) Set to FULL SEQUENTIAL ACTUATION

MECHANISM.

2) Pull the trigger rapidly and ﬁ rmly.

Set the nailing operation switch to FULL SEQUENTIAL

ACTUATION MECHANISM (Nailing operation indicator

is light in blue.)

(to set to FULL SEQUENTIAL ACTUATION

MECHANISM).

(Set the switching device to the nailing operation

indicator light in blue mode completely as shown in

the Fig. 17. Otherwise, it will be set to CONTACT

ACTUATION MECHANISM.)

Position the nail outlet on the workpiece with ﬁ nger oﬀ

the trigger.

Depress the push lever ﬁ rmly until it is completely

depressed.

Pull the trigger to drive a nail.

Remove ﬁ nger from the trigger and lift the tool oﬀ the

wood surface completely.

To continue nailing in a separate location, move the nailer

along the wood, repeating steps - as required.

NOTE

Operations and should be done within 2 seconds

of each other. If more than 2 seconds pass after , the

Nailer will not work properly. If this happens, retry from

(2) Continuous operation (Push lever ﬁ re)

Using CONTACT ACTUATION MECHANISM (See Fig.

18)

WARNING

To avoid double ﬁ ring or accidental ﬁ ring due to recoil.

1) Do not press the nailer against the wood with

excessive force.

2) Separate the nailer from the wood as it recoils after

nailing.

Set the nailing operation switch to CONTACT

ACTUATION MECHANISM (Nailing operation indicator

is blink in blue.)

(to set to CONTACT ACTUATION MECHANISM).

(Set the switching device to the nailing operation

indicator blink in blue completely as shown in the

Fig. 18. Otherwise, it will not operate properly.)

Pull the trigger with the Nailer oﬀ the workpiece.

Depress the push lever against the workpiece to drive a

nail.

Move the Nailer along the workpiece with a bouncing

motion.

Each depression of the push lever will drive a nail.

As soon as the desired number of nails have been driven,

remove ﬁ nger from the trigger.

NOTE

Operations and should be done within 2 seconds

of each other. If more than 2 seconds pass after , the

Nailer will not work properly. If this happens, retry from

WARNING

○ Keep your ﬁ nger oﬀ the trigger except during nailing

operation, because serious injury could result if the push

lever accidentally contacts you or others in work area.

○ Keep hands and body away from the discharge area.

This HiKOKI nailer may bounce from the recoil of driving

a nail and unwanted subsequent nail may be driven,

possibly causing injury.

NOTE

○ If all warnings and instructions are followed, safe

operation is possible with all two systems: FULL

SEQUENTIAL ACTUATION MECHANISM, CONTACT

ACTUATION MECHANISM.

○ Always handle nails and package carefully. If nails are

dropped, collating bond may be broken, which will cause

mis-feeding and jamming.

○ After nailing:

1) remove battery from the Nailer;

2) remove all nails from the Nailer;

2. Adjusting the nailing depth

To assure that each nail penetrates to the same depth,

be sure that the Nailer is always held ﬁ rmly against the

workpiece.

If nails are driven too deep or shallow into the workpiece,

adjust the nailing in the following order.

Remove the battery from the Nailer.

If nails are driven too deep, turn the adjuster to the

shallow side. (See Fig. 19)

Adjustments are in half-turn increments.

If nails are driven too shallow, turn the adjuster to the

deep side. (See Fig. 20)

Stop turning the adjuster when a suitable position is

reached for a nailing test.

Connect the battery to the Nailer.

ALWAYS WEAR SAFETY GLASSES.

Perform a nailing test.

Remove the battery from the Nailer.

Choose a suitable position for adjuster.

3. Using the hook (See Fig. 21, 22, 23)

WARNING

When using the hook, turn oﬀ the power switch (green

light “OFF”). Pay suﬃ cient attention so that the main

equipment does not fall.

If the tool falls, there is a risk of accident.

Hook can be installed on the left or right side. (excluding

NT1865DBAL and NT1865DA)

Remove the battery, then remove all remaining nails

from the magazine.

Securely hold the main unit and remove the screw using

a screwdriver. (See Fig. 21)

Remove the hook and hook plate. (See Fig. 22)

Install the hook on the other side and securely fasten

with screw. (See Fig. 23)

NOTE

Hook can be used as a hanger.

4. Using the nose cap (See Fig. 24, 25)

WARNING

When attaching or detaching the nose cap, be sure

to remove your ﬁ nger from the trigger and remove all

remaining fasteners and the battery from the nailer.

If you like to protect the surface of workpiece against

scratches or markings made by the push lever, attach the

accessory nose cap to the push lever.

Remove all remaining fasteners and battery from nailer.

Put the nose cap to the toe of the push lever.

The nose cap is marked to indicate the exit point of the

nail, making alignment easier.

When not using the nose cap, secure in the storage

compartment located on the reverse side of the

magazine.

NOTE

The nose cap may reduce nailing depth due to its

thickness. Re-adjustment of nailing depth is required.

5. Clearing a jam

If nails are jammed in ﬁ ring head, remove it, and adjust

the nailing in the following order.

CAUTION

Remove the battery from the Nailer.

Remove all nails.

Release the Lock lever and open guide plate. (See

Fig. 26)

Remove the jammed nail with a slotted-head screwdriver.

(See Fig. 27)

000BookNT1865DBAL.indb21000BookNT1865DBAL.indb21 2022/06/2911:54:382022/06/2911:54:38

Hikoki NT1865DBAL Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info