Bedienungsanleitung Hikoki R 18DB (Seite 9 von 136) (Alle Sprachen)

742692

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

English

UNPACKING

Carefully unpack the power tool.

CHARGING

Battery and battery charger are not included with this

product.

For rechargeable batteries, please charge in according

to the handling instructions of the charger which you are

using.

MOUNTING AND OPERATION

Action Figure Page

Removing and inserting the battery

(sold separately)

Dismounting the dust case 3 2

Dismounting the ﬁ lter 4 2

Check the ﬁ lter

Mounting the ﬁ lter

Mounting the dust case

Switch operation

The indicator lamp

How to use

10 4

Emptying the dust case

11 5

Eﬀ ectively removing dust

12 5

Selecting accessories ― 130

*1 a. Filter free of debris and dust

b. Rubber not deteriorated

c. Connector free of damage

*2 If the ﬁ lter is not properly ﬁ tted, dirt or grime can enter

the fan unit and cause damage or malfunction.

*3 The dust case can also be installed with the nozzle

facing upwards. (Fig. 7-a)

Mode

Continuous operating time

BSL1850/BSL36A18

3 (HIGH) Approx. 40 min.

2 (MID) Approx. 48 min.

1 (LOW) Approx. 66 min.

∗ Continuous operating time will vary according

to battery condition. Please use the table as a

guideline.

NOTE

To suppress noise when using the appliance,

switch to 1 mode.

*5 When the battery supply is low during operation of the

appliance, the indicator lamp will light up. When this

occurs, please recharge the appliance.

*6 When attaching the nozzle or extension pipe, insert as

you twist in the direction indicated by the arrow.

Twist in the direction indicated by the arrow when

detaching as well. (Fig. 10-a)

Twisting in the opposite direction could result in

detaching the dust case from the housing.

*7 NOTE

○ Point the intake port downward as dust can spill

when removing the dust case.

○ If the suction does not recover after disposing the

dust, clean the ﬁ lter. (See “Cleaning the ﬁ lter” on

page 9.)

*8 The appliance has a built-in mechanism for scraping

oﬀ dust attached to the ﬁ lter when removing the dust

case.

To even more eﬀ ectively scrape oﬀ the dust, repeatedly

turn the dust case back and forth (2 to 3 times or more).

Holding the unit so that the dust case does not detach

from the housing, slightly and repeatedly turn the dust

case in the indicated directions.

MAINTENANCE AND INSPECTION

WARNING

○ For inspection and maintenance, be sure to turn oﬀ the

switch and disconnect the battery.

○ Do not work with wet hands. May cause electric shock

or injuries.

1. Cleaning the ﬁ lter

CAUTION

○ Do not wash the ﬁ lter in a washing machine.

○ Do not wash the ﬁ lter in hot water or dry it by ﬁ re.

○ Do not detach the fan ﬁ lter and the ﬁ lter holder.

If the vacuuming eﬃ ciency is poor even when the dust

case has been emptied, remove the ﬁ lter and wash it in

cold or warm water. (The water should not be hot to the

touch.)

After washing, dry out of direct sunlight. (Fig. 13-a)

If there is dust on the fan ﬁ lter, hold the cleaner with the

fan ﬁ lter pointing downwards to keep dust from entering

the motor and lightly clean with a small brush such as a

used toothbrush. Do not brush vigorously. (Fig. 13-b)

NOTE

○ Do not use gasoline, thinner, benzene or kerosene as

they can melt plastic.

○ Do not use an air gun or similar tool to clean the ﬁ lter,

fan ﬁ lter or the appliance itself. (Fig. 13-c)

Doing so could push dirt into the appliance and cause

malfunction.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspection of terminals

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

5. Cleaning of the outside

When the tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, as they melt

plastics.

6. Storage

Store the cordless cleaner in a place in which the

temperature is less than 50°C and out of reach of

children.

When storing the appliance in a vertical position, hook

the strap to a hanger.

000Book_R18DB_EU.indb 9000Book_R18DB_EU.indb 9 2020/07/10 9:49:392020/07/10 9:49:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki R 18DB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info