Bedienungsanleitung Hikoki UB18DC (Seite 8 von 148) (Alle Sprachen)

816276

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

English

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○ Since the built-in micro computer takes about 3 seconds

to conﬁ rm that the battery being charged with charger

is taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

MOUNTING AND OPERATION

Action Figure Page

Inserting the battery 2-a 2

Removing the battery 2-b 2

Charging 3 2

Turning the work light on*142

Changing the angle of the work light 5 3

Mounting on a wall for use 6 3

Securing to a tripod*273

Remaining battery indicator*383

Charging a USB device*493

Selecting accessories ―139

*1 When the brightness reaches the maximum (4000 lm) or

the minimum (700 lm), the light brieﬂ y blinks twice.

NOTE

When using a tripod, ensure that it is stable so that it

does not fall over.

State of lamp Battery Remaining Power

Over 80%

60%–80%

40%–60%

20%–40%

Less than 20%

When the remaining battery becomes low, the light brieﬂ y

blinks about once every 3 minutes.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and battery

characteristics, read it as a reference.

NOTE

○ When using a Multi-volt battery, please refer to the

indicator lamp on the battery for the battery remaining

power.

○ Do not give a strong shock to the panel or break it. It may

lead to a trouble.

NOTE

○ If the remaining battery becomes low, USB output is

automatically stopped, and the work light cannot charge

USB devices.

○ The charging time diﬀ ers depending on the type of USB

device being used.

○ Do not use for any purpose other than charging a USB

device.

(Refer to “USB DEVICE CONNECTION

PRECAUTIONS”.)

MAINTENANCE AND INSPECTION

WARNING

When not using the work light for a long time, performing

maintenance on it, inspecting it, or storing it, be sure to

turn OFF the switch and pull out the battery.

1. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

2. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

3. Cleaning on the outside

When the cordless work light is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water.

Do not use chloric solvents, gasoline or paint thinner, for

they melt plastics.

4. Storage

Store the cordless work light and the battery in a place in

which the temperature is less than 40°C and out of reach

of children.

00BookUB18DC.indb800BookUB18DC.indb8 2023/05/2510:08:422023/05/2510:08:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki UB18DC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info