Bedienungsanleitung Hikoki UB18DD (Seite 8 von 156) (Alle Sprachen)

816277

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

English

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○ Since the built-in micro computer takes about 3 seconds

to conﬁ rm that the battery being charged with charger

is taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

MOUNTING AND OPERATION

Action Figure Page

Inserting the battery 2-a 2

Removing the battery 2-b 2

Attaching and removing the AC cord*132

Changing 4 3

Opening the stand 5 3

Turning the work light on*263

Securing to a tripod*373

Remaining battery indicator*483

Charging a USB device*593

Selecting accessories ―147

Pull back the rubber cover and insert the plug of the AC

cord all the way into the socket. The lock ring rotates

simultaneously and secures the connection in place.

Next, plug the AC cord into an electrical outlet.

To detach the AC cord, turn the lock ring counter-

clockwise and hold it in that position while pulling out the

AC cord.

NOTE

○ When used together with the battery, the AC cord is the

main power source and no battery power is consumed.

○ The work light has no charging function. Using the AC

cord and rechargeable battery simultaneously will not

charge the battery.

○ Ensure that the rubber cover of the AC socket is securely

closed when the AC cord is not attached.

If any water or dust enters the body of the tool or the

terminals of the AC socket, a failure may occur.

*2 When the brightness reaches the maximum (10000 lm)

or the minimum (1000 lm), the light brieﬂ y blinks twice.

*3 If the screw of the tripod is less than 20 mm long, attach

the included adapter to the tripod before fastening the

work light.

NOTE

○ Use a tripod that can support a load of 5.5 kg or more.

○ When using a tripod, ensure that it is stable so that it

does not fall over.

Use a method to prevent the tripod from falling over that

is suitable for the usage environment, such as securing

its legs in place.

State of lamp Battery Remaining Power

Over 80%

60%–80%

40%–60%

20%–40%

Less than 20%

When the remaining battery becomes low, the light brieﬂ y

blinks about once every 3 minutes.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and battery

characteristics, read it as a reference.

NOTE

○ When the AC cord is connected, the remaining battery

indicator does not light up.

○ When using a Multi-volt battery, please refer to the

indicator lamp on the battery for the battery remaining

power.

○ Do not give a strong shock to the panel or break it. It may

lead to a trouble.

00BookUB18DD.indb800BookUB18DD.indb8 2023/05/2510:31:562023/05/2510:31:56

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikoki UB18DD Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info