Bedienungsanleitung Hikoki UR18DA (Seite 8 von 168) (Alle Sprachen)

816256

Zoom out

Zoom in

Vorherige Seite

1/168

Nächste Seite

English

● Regarding the temperatures and charging time of the

battery.

The temperatures and charging time will become as

shown in Table 2.

Table 2

Charger UC18YFSL

Battery

Type of battery Li-ion

Temperatures at which the

battery can be recharged 0°C–50°C

Charging voltage V 18

Charging time,

approx. (At 20°C)

BSL36B18

(10 cells)

min 120

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate, and

the battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used,

the pilot lamp of the charger lights up green or lights

for 1 second, does not light for 0.5 seconds (oﬀ for

0.5 seconds). In such a case, ﬁ rst let the battery cool,

then start charging.

○ When the pilot lamp ﬂ ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects in

the charger’s battery connector. If there are no foreign

objects, it is probable that the battery or charger is

malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about 3 seconds

to conﬁ rm that the battery being charged with chargers

are taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

BATTERY INSTALLATION

CAUTION

Do not touch the terminals.

Doing so may result in cuts to the hand or other injuries.

Only HiKOKI battery model BSL36B18 can be used with this

device.

Installing the battery

Align the battery with the groove in tool and slip it into place.

Always insert it all the way until it locks in place with a little

click, If not, it may accidentally fall out of the tool, causing

injury to you or someone around you (Fig. 1).

Removing the battery

Withdraw battery from the tool while pressing the latch

(2 pcs) of the battery (Fig. 1).

NOTE

○ Do not apply any excessive pressure when inserting the

battery. If the battery does not easily slide into place, it is

not being inserted properly.

Check to see if the battery is facing the correct direction

and that there is nothing obstructing the path of insertion.

○ If is displayed when the device is switched on

following battery installation, the battery charge is low.

In this situation, either use the AC adapter or install a fully

charged battery.

AC ADAPTER INSTALLATION

Power can be supplied by plugging the AC adapter

(included) into a standard household outlet.

Pull back the rubber cover and connect the AC adapter to

the AC adapter port. (Fig. 2)

Next, plug the AC adapter into an electrical outlet.

NOTE

○ When used together with the battery, the AC adapter

is the main power source and no battery power is

consumed.

○ When used together with the AC adapter, the battery will

not recharge as this device has no recharge function.

USE

1. Switching On and Oﬀ

To switch on: Press button.

To switch oﬀ : Press button again.

2. Adjusting the volume

Increase volume: press “+” button.

Decrease volume: press “–” button.

3. Change between FM (ultra shortwave), AM (medium

wave), Bluetooth (BT) and DAB / DAB+

The set mode is shown in the display (FM / AM / BT/

DAB).

To change between FM (ultra shortwave / UKW), AM

(medium wave), BT (Bluetooth) and DAB / DAB+, press

the “MODE” button several times.

4. Searching for radio stations

Press “│<<” button or “>>│” button to change the

frequency. The current frequency is shown on the

display.

To search the next radio station with high signal

strength, press the “│<<” button or press the “>>│”

button and keep pressed brieﬂ y. The frequency of the

radio station found is shown on the display.

00BookUR18DAEU.indb800BookUR18DAEU.indb8 2022/12/1315:40:262022/12/1315:40:26

Hikoki UR18DA Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info