Bedienungsanleitung Hikoki VB3616DA (Seite 18 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

816254

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

English

(1) Remove battery cover and battery (Fig. 5-a)

(2) Make sure the switch lock is in the lock position. (Fig. 17)

(3) Position the tool so that the turn table is facing upwards

(Fig. 24)

(4) Make sure the cutter’s cover is closed (Fig. 24)

(5) Attach the battery and battery cover (Fig. 5-b)

(6) Align the setting dial to the appropriate size color and

angle of the rebar to be bent. (Fig. 25)

[Adjusting for the sizes of rebars]

Although the bend angle is the same on the dial, the

angle will slightly change depending on the rebar’s

thickness.

Adjust the angle in accordance with the size color on the

setting dial.

Size of rebar Colors of indicated marks

ø10 mm White

ø12 mm Green

ø16 mm Silver

NOTE

Even at the same dial setting position, the bending angle

can sometimes diﬀ er if the diameter or hardness of the

rebar is diﬀ erent. Use the angle marks merely as a rough

guideline.

(7) Properly setup by placing the rebar against the guide’s

stopper (Fig. 26)

(8) Press the switch lock to release the lock and pull the

switch to bend the rebar. (Fig. 7)

Even after the rebar is bent, the motor will reverse-rotate

and the roller will return to position while the switch is

pulled.

When the roller begins returning to position, it will

continue to do so even if the switch is released.

(See “[OPERATION]; 1. Switch operation”)

2. Bending in Manual Mode

In addition to “bending according to dial setting”, this

tool uses a variable speed switch to allow the bending of

rebars according to “visual estimation”.

After steps (1) through (5) of “1. Normal bending

procedure” have been completed, follow the instructions

below.

(1) Set the setting dial to a larger angle Ⓛ than the one

desired Ⓡ (Fig. 27)

(2) Set the rebar and release the switch lock (See

“[OPERATION]; 1. Switch operation”) (Fig. 7)

(3) Pull the switch and release at the desired angle Ⓡ

(Fig. 30 )

The roller will move as long as the switch is pulled. Little

by little, pull the switch a few times to adjust until the

desired angle is reached.

(4) Verify the bent angle

Press the Manual Mode switch to slightly reverse-rotate

the bending roller. (Fig. 28)

If the desired bending angle Ⓡ is reached, go to step (5).

If the angle requires more bending, press the Manual

Mode switch to return to normal rotation and bend a little

more.) (Fig. 29) (Fig. 30 )

(5) When the rebar is bent to the desired angle, keep pulling

the switch in reverse-rotation mode, until the roller is

returned to its original position. (Fig. 30 )

(6) When the bending roller stops after returning to its

original position, press the Manual Mode switch once

again to cancel reverse-rotation. (Fig. 29)

3. Using holes to ﬁ x unit in place.

When using this product, place it in a stable position on

ﬂ oor or ground.

At the center of the tool is a hole for securing the unit in

place and a screw hole located on the notch part of the

inner cover.

Use these holes to secure the tool to a work bench or

other location. (Bolt size: M10) (Fig. 31)

3. Cutter Replacement

After following the steps for “1. Inspect the cutter and grip

rubber” (steps (1) through (5)), follow the instructions below.

Replace the upper and lower cutters as one set.

(1) Using the included hexagonal bar wrench, remove the

hexagon socket bolt and then remove the upper and

lower cutters.

Pushing the cutter guard upwards makes it easier to

remove the upper cutter. (Fig. 20)

Prying with a ﬂ athead screwdriver will make it easier to

remove the lower cutter. (Fig. 21)

(2) Clean away the iron ﬁ lings attached around the cutter

installation area (Fig. 22)

WARNING

Wear protective goggles.

(3) Align the hole of the cutter with the position of the pin and

attach the cutter.

Using the included hexagonal bar wrench, ﬁ rmly tighten

the hexagon socket bolt to secure the cutter.

Exchange the hexagon socket bolt with the new one

included with the cutter. (Fig. 23)

(4) Attach the battery and battery cover (Fig. 10)

HOW TO USE (BENDING)

1. Normal bending procedure

WARNING

○ Note that the unit is not a hand-held tool. Be absolutely

sure to use the unit only after placing it on a stable spots

such as ﬂ oor, ground, etc.

○ Never bring your hand close to the bending roller during

operation.

○ Never bend any materials other than the rebars. If you

attempt to do so, the material can splinter into pieces

and scatter.

○ Bend less than every 3 pieces of rebar with a 10 mm

diameter, less than every 2 pieces with a 12 mm

diameter, and every 1 piece with a 16 mm diameter.

○ Remember that the cutter moves even during the

bending operation, thereby, close the cutter cover

without fail. (Fig. 24)

○ Begin operation only after making

sure that there are no people within

the turning range of the material to be

bent.

○ Reserve an extra length of at least

200 mm on the bending length of the

rebar to be bent. (Fig. 26)

If the extra length is not long enough, the rebar can

come oﬀ during bending operation, or it can break into

fragments and scatter dangerously.

○ Place the rebar on the center plate and set it so that it is

horizontal with the turntable surface.

If the side that is to be bent is set inclined upward, the

rebar can come loose from the bending roller while

bending causing it to ﬂ y oﬀ .

○ When bending multiple rebars at one time, some may

come oﬀ the bending roller and guide, etc., and therefore

exercise caution and set them horizontally.

○ If you bend the rebar with a large angle

while placing your hand onto it, there is a

fear of getting your hand caught in by the

fold-back reaction of the rebar. Never

place your hand onto the position where

the rebar may fold back.

0000BookVB3616DA.indb180000BookVB3616DA.indb18 2023/02/1715:02:582023/02/1715:02:58

Hikoki VB3616DA Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info