Bedienungsanleitung Hikvision DS-7216HVI-S (Seite 29 von 65) (Englisch)

629377

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

Hikvision EURO, Inc. – DS-7208&7216HVI-S Series Embedded Net DVR User Manual

frame can be selected.

6. Set the picture quality using the Picture Quality slider. Increasing the picture quality will also increase the

bit rate of the video feed. The resolution and frame rate of the feed will be adjusted automatically.

7. Select the Pre-record time. The pre-record time is the time in seconds to also record before a recording is

triggered. Setting the pre-record time to MAX will allow the DVR to use up to the maximum available buffer

space for recording.

8. Select the Post-record time. The post-record time is the time in seconds to also record after a recording has

ended.

9. Enter the erase video after time. The Erase Video After time denotes the amount of days that files will be

deleted after its initial recording. Setting the time to 0 will allow the DVR to only delete and overwrite files when

the HDD is full.

10. Repeat steps 3-9 for other Encoding Parameters mode.

11. Select the Save button to save the recording quality settings and select Exit to return to the previous menu.

Selecting the Exit button without clicking Save will quit out of the menu without saving settings.

Configuring a Quick Recording Schedule

A quick recording schedule allows you to set one time period per day for recording. To setup a quick recording

schedule:

1. Enter the Quick Schedule Configuration menu, shown in Figure 23 by going to Main Menu > Recording

Configuration > Quick Schedule Configuration.

Figure 23. Quick Schedule Configuration Menu

2. Select the camera to configure from the camera drop down menu. If all the cameras are to be configured

with the same settings, select All Cameras from the list.

3. Check the Enable checkbox to enable the recording schedule. If the checkbox is unchecked, the recording

schedule will be disabled.

4. Check the 24/7 checkbox if you would like to record continuously or on event for 24 hours a day, 7 days a

week. If you wish to schedule different frames for Monday through Sunday, leave the 24/7 checkbox unchecked

and skip to step 6.

5. Select Recording Type for 24/7 recording and move on to step 8. Recording type includes Continuous for

continuous recording or On Event for recording when an event is triggered (i.e. from detected motion).

6. Select the start and stop time for each day of the week. The start and stop time are listed using a 24 hr cycle

(i.e. 18:00 is equivalent to 6:00pm).

7. Select Recording Type for each day of the week. Recording type includes Continuous for continuous

recording or On Event for recording when an event is triggered (i.e. from detected motion) for the selected time

period.

8. Select the Save button to save the schedule settings and select Exit to return to the previous menu. Selecting

the Exit button without clicking Save will quit out of the menu without saving settings.

Note: On Event recordings are recordings that are triggered from motion detection and/or from an external

alarm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikvision DS-7216HVI-S Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info