662621
201
Zoom out
Zoom in
Vorherige Seite
1/225
Nächste Seite
Network Video Recorder
User Manual
UD.6L0202D2006A01
User Manual of Network Video Recorder
1
Quick Start Guide
COPYRIGHT ©2015 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou
Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user
manual (hereinafter referred to be the Manual) cannot be reproduced, changed, translated, or distributed,
partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated,
Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the
Manual.
About this Manual
This Manual is applicable to Network Video Recorder (NVR).
The Manual includes instructions for using and managing the product. Pictures, charts, images and all other
information hereinafter are for description and explanation only. The information contained in the Manual is
subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the
company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvisions trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH
ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED AS IS, WITH ALL FAULTS AND
ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATER PREVAILS.
User Manual of Network Video Recorder
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the EMC Directive
2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
User Manual of Network Video Recorder
3
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
Proper configuration of all passwords and other security settings is the responsibility of the installer and/or
end-user.
In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation
and region. Please refer to technical specifications for detailed information.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with
100~240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for
detailed information.
Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire
hazard.
Please make sure that the plug is firmly connected to the power socket.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the service center.
Warnings Follow these
safeguards to prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
User Manual of Network Video Recorder
4
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
Ensure unit is installed in a well-ventilated, dust-free environment.
Unit is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
A factory recommended HDD should be used for this device.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the manufacturer.
User Manual of Network Video Recorder
5
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
The figures in the manual are for reference only.
This manual is applicable to the models listed in the following table.
Series
Models
DS-7600NI-E1/E2 series
DS-7604NI-E1, DS-7608NI-E1, DS-7616NI-E1
DS-7604NI-E1/4P
DS-7604NI-E1/4N
DS-7608NI-E2, DS-7616NI-E2, DS-7632NI-E2
DS-7608NI-E2/8P, DS-7616NI-E2/8P, DS-7616NI-E2/16P,
DS-7632NI-E2/8P, DS-7632NI-E2/16P
DS-7608NI-E2/8N, DS-7616NI-E2/8N, DS-7632NI-E2/8N
DS-7616NI-E2/16N, DS-7632NI-E2/16N
DS-7700NI-E4 series
DS-7708NI-E4, DS-7716NI-E4, DS-7732NI-E4
DS-7708NI-E4/8P, DS-7716NI-E4/16P, DS-7732NI-E4/16P
DS-8600NI-E8 series
DS-8608NI-E8, DS-8616NI-E8, DS-8632NI-E8
User Manual of Network Video Recorder
6
Product Key Features
General
Connectable to network cameras, network dome and encoders.
Connectable to the third-party network cameras like ACTI, Arecont, AXIS, Bosch, Brickcom, Canon,
PANASONIC, Pelco, SAMSUNG, SANYO, SONY, Vivotek and ZAVIO, and cameras that adopt ONVIF
or PSIA protocol.
Connectable to the smart IP cameras.
PAL/NTSC adaptive video inputs.
Each channel supports dual-stream.
Up to 32 network cameras can be connected for DS-8600NI-E8, DS-7700NI-E4 and DS-7600NI-E2 series
NVR; 16 network cameras for other DS-7600NI models, series NVR.
Independent configuration for each channel, including resolution, frame rate, bit rate, image quality, etc.
The quality of the input and output record is configurable.
Local Monitoring
Simultaneous HDMI
TM
and VGA outputs.
HDMI
TM
and VGA outputs at up to 1920×1080 resolution.
Multiple screen display in live view is supported, and the display sequence of channels is adjustable.
Live view screen can be switched in group, and manual switch and automatic cycle live view are also
provided, and the interval of automatic cycle can be adjusted.
Quick setting menu is provided for live view.
Motion detection, video tampering, VCA (Video Content Analysis) alarm, video exception alert and video
loss alert functions.
Privacy mask.
Multiple PTZ protocols supported; PTZ preset, patrol and pattern.
Zooming in by clicking the mouse and PTZ tracing by dragging mouse.
The PTZ control is supported by the DS-8600NI-E8 and DS-7700NI-E4 series NVR only.
HDD Management
For DS-8600NI-E8 series, 8 SATA hard disks can be connected;
For DS-7700NI-E4 series, 4 SATA hard disks can be connected;
For DS-7600NI-E2 series, 2 SATA hard disks can be connected;
For DS-7600NI-E1 series, 1 SATA hard disk can be connected;
Each disk with a maximum of 6TB storage capacity for the DS-8600NI-E8. DS-7700NI-E4,
DS-7600-E1(E2) series NVR.
8 network disks (NAS /IP SAN disks) can be connected.
Support S.M.A.R.T. and bad sector detection.
HDD group management.
Support HDD standby function.
HDD property: redundancy, read-only, read/write (R/W).
HDD quota management; different capacity can be assigned to different channel.
Recording and Playback
Holiday recording schedule configuration.
Continuous and event video recording parameters.
User Manual of Network Video Recorder
7
Multiple recording types: manual, continuous, alarm, motion, motion | alarm, motion & alarm, and VCA.
8 recording time periods with separated recording types each day.
Pre-record and post-record for alarm, motion detection for recording, and pre-record time for schedule and
manual recording.
Searching record files by events (alarm input/motion detection/VCA).
Playback by sub-periods.
Tag adding for record files, searching and playing back by tags.
Locking and unlocking record files.
Local redundant recording.
Provide new playback interface with easy and flexible operation.
Searching and playing back record files by camera No., recording type, start time, end time, etc.
Smart search for the selected area in the video.
Zooming in when playback.
Reverse playback of multi-channel.
Supports pause, play reverse, speed up, speed down, skip forward, and skip backward when playback, and
locating by dragging the mouse.
Up to 4/816-ch synchronous playback.
Support enabling H.264+ to ensure high video quality with lowered bitrate.
Backup
Export video data by USB or SATA device.
Export video clips when playback.
Management and maintenance of backup devices.
Alarm and Exception
Configurable arming time of alarm input/output.
Alarm for video loss, motion detection, VCA, video tampering, HDD full, HDD error, network
disconnected, IP confliction, illegal login, abnormal record, and PoE power overload (for the models
support PoE interfaces only), etc.
Alarm triggers full screen monitoring, audio alarm, notifying surveillance center, sending email and alarm
output.
Automatic restore when system is abnormal.
Support VCA detection alarm and VCA search.
Other Local Functions
Operable by front panel (depends on model), mouse, and remote control.
Three-level user management; admin user is allowed to create many operating accounts and define their
operating permission, which includes the limit to access any channel.
Operation, alarm, exceptions and log recording and searching.
Manually triggering and clearing alarms.
Import and export of device configuration information.
Network Functions
The dual-NIC network 10 /100/1000 Mbps self-adaptive Ethernet interfaces are provided for the
DS-8600NI-E8 and DS-7700NI-E4 series NVR; one 10 /100 Mbps self-adaptive Ethernet interface for
DS-7604/7608NI-E1(E2) series NVR; and one 10 /100/1000 Mbps self-adaptive Ethernet interface for
other models.
1 self-adaptive 10M/100M/1000M network interfaces are provided for other models.
4 independent PoE network interfaces are provided for DS-7600NI-E1/P series.
User Manual of Network Video Recorder
8
Up to 8 independent PoE network interfaces are provided for DS-7600NI-E2/P series.
And up to 16 independent PoE network interfaces are provided for DS-7700NI-E4/P series.
4 independent built-in switch network interfaces are provided for DS-7600NI-E1/N series.
Up to 8 independent built-in switch network interfaces are provided for DS-7600NI-E2/N series;
IPv6 is supported.
TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and iSCSI are supported.
TCP, UDP and RTP for unicast.
Auto/Manual port mapping by UPnP
TM
.
Extranet access by HiDDNS.
Support access by EZVIZ Cloud P2P.
Remote reverse playback via RTSP.
Support accessing by the platform via ONVIF.
Remote search, playback, download, locking and unlocking of the record files, and the breakpoint resume
is supported for downloading files.
Remote parameters setup; remote import/export of device parameters.
Remote viewing of the device status, system logs and alarm status.
Remote keyboard operation.
Remote locking and unlocking of control panel and mouse.
Remote HDD formatting and program upgrading.
Remote system restart and shutdown.
RS-232, RS-485 transparent channel transmission (depending on models).
Alarm and exception information can be sent to the remote host
Remotely start/stop recording.
Remotely start/stop alarm output.
Remote PTZ control (depending on models).
Remote JPEG capture.
Two-way audio and voice broadcasting.
Embedded WEB server.
Development Scalability:
SDK for Windows and Linux system.
Source code of application software for demo.
Development support and training for application system.
User Manual of Network Video Recorder
9
TABLE OF CONTENTS
Product Key Features .............................................................................................................................. 6
Chapter 1 Introduction ........................................................................................................................ 13
1.1 Front Panel .................................................................................................................................... 14
DS-8600NI-E8 Series....................................................................................................................... 14
DS-7700NI-E4 Series....................................................................................................................... 16
DS-7600NI-E1(E2) Series ............................................................................................................... 18
1.2 IR Remote Control Operations ...................................................................................................... 19
1.2 USB Mouse Operation .................................................................................................................. 22
1.3 Input Method Description .............................................................................................................. 23
1.4 Rear Panel ..................................................................................................................................... 24
DS-8600NI-E8, DS-7700NI-E4 and DS-7700NI-E4/P Series ......................................................... 24
DS-7600NI-E1, DS-7600NI-E1/4N, DS-7600NI-E2 and DS-7600NI-E2/8N Series ....................... 25
DS-7600NI-E1/4P and DS-7600NI-E2/8P Series ............................................................................ 26
Chapter 2 Getting Started ................................................................................................................... 27
2.1 Starting Up and Shutting Down the NVR ...................................................................................... 28
2.2 Setting Admin Password ................................................................................................................ 30
2.3 Using the Wizard for Basic Configuration..................................................................................... 31
2.4 Login and Logout .......................................................................................................................... 35
2.4.1 User Login ........................................................................................................................ 35
2.4.2 User Logout ...................................................................................................................... 35
2.5 Adding and Connecting the IP Cameras ........................................................................................ 37
2.5.1 Activating the IP Camera .................................................................................................. 37
2.5.2 Adding the Online IP Cameras ......................................................................................... 38
2.5.3 Editing the Connected IP cameras and Configuring Customized Protocols ...................... 41
2.5.4 Editing IP Cameras Connected to the PoE Interfaces ....................................................... 44
Chapter 3 Live View ............................................................................................................................. 47
3.1 Introduction of Live View ............................................................................................................. 48
3.2 Operations in Live View Mode ...................................................................................................... 49
3.2.1 Front Panel Operation on Live View................................................................................. 49
3.2.2 Using the Mouse in Live View ......................................................................................... 49
3.2.3 Quick Setting Toolbar in Live View Mode ....................................................................... 50
3.3 Adjusting Live View Settings ........................................................................................................ 53
3.4 Channel-zero Encoding ................................................................................................................. 54
Chapter 4 PTZ Controls ...................................................................................................................... 55
4.1 Configuring PTZ Settings .............................................................................................................. 56
4.2 Setting PTZ Presets, Patrols & Patterns......................................................................................... 58
4.2.1 Customizing Presets .......................................................................................................... 58
4.2.2 Calling Presets .................................................................................................................. 58
4.2.3 Customizing Patrols .......................................................................................................... 59
4.2.4 Calling Patrols .................................................................................................................. 60
4.2.5 Customizing Patterns ........................................................................................................ 61
4.2.6 Calling Patterns ................................................................................................................. 61
User Manual of Network Video Recorder
10
4.2.7 Customizing Linear Scan Limit ........................................................................................ 62
4.2.8 Calling Linear Scan .......................................................................................................... 63
4.2.9 One-touch Park ................................................................................................................. 63
4.3 PTZ Control Panel ......................................................................................................................... 65
Chapter 5 Recording Settings.............................................................................................................. 66
5.1 Configuring Parameters ................................................................................................................. 67
5.2 Configuring Recording Schedule .................................................................................................. 70
5.3 Configuring Motion Detection Recording ..................................................................................... 73
5.4 Configuring Alarm Triggered Recording ....................................................................................... 75
5.5 Configuring VCA Event Recording ............................................................................................... 77
5.6 Manual Recording ......................................................................................................................... 78
5.7 Configuring Holiday Recording .................................................................................................... 79
5.8 Configuring Redundant Recording ................................................................................................ 80
5.9 Configuring HDD Group for Recording ........................................................................................ 82
5.10 Files Protection .............................................................................................................................. 83
5.10.1 Locking the Recording Files ............................................................................................. 83
5.10.2 Setting HDD Property to Read-only ................................................................................. 85
Chapter 6 Playback .............................................................................................................................. 87
6.1 Playing Back Record Files ............................................................................................................ 88
6.1.1 Instant Playback ................................................................................................................ 88
6.1.2 Playing Back by Normal Search ....................................................................................... 88
6.1.3 Playing Back by Event Search .......................................................................................... 91
6.1.4 Playing Back by Tag ......................................................................................................... 92
6.1.5 Playing back by Smart Playback ....................................................................................... 94
6.1.6 Playing Back by System Logs .......................................................................................... 97
6.1.7 Playing Back External File ............................................................................................... 98
6.1.8 Playing Back by Sub-periods ............................................................................................ 99
Chapter 7 Backup .............................................................................................................................. 100
7.1 Backing up Record Files ............................................................................................................. 101
7.1.1 Quick Export ................................................................................................................... 101
7.1.2 Backing up by Normal Video Search .............................................................................. 103
7.1.3 Backing up by Event Search ........................................................................................... 105
7.1.4 Backing up Video Clips .................................................................................................. 106
7.2 Managing Backup Devices .......................................................................................................... 107
Chapter 8 Alarm Settings .................................................................................................................. 108
8.1 Setting Motion Detection Alarm .................................................................................................. 109
8.2 Setting Sensor Alarms ................................................................................................................. 111
8.3 Detecting Video Loss Alarm ........................................................................................................ 114
8.4 Detecting Video Tampering Alarm .............................................................................................. 115
8.5 Handling Exceptions Alarm ......................................................................................................... 117
8.6 Setting Alarm Response Actions ................................................................................................. 118
8.7 Triggering or Clearing Alarm Output Manually .......................................................................... 121
Chapter 9 VCA Alarm ....................................................................................................................... 122
9.1 Face Detection ............................................................................................................................. 123
User Manual of Network Video Recorder
11
9.2 Vehicle Detection ........................................................................................................................ 124
9.3 Line Crossing Detection .............................................................................................................. 126
9.4 Intrusion Detection ...................................................................................................................... 128
9.5 Region Entrance Detection .......................................................................................................... 130
9.6 Region Exiting Detection ............................................................................................................ 131
9.7 Loitering Detection ...................................................................................................................... 131
9.8 People Gathering Detection ......................................................................................................... 131
9.9 Fast Moving Detection ................................................................................................................ 131
9.10 Parking Detection ........................................................................................................................ 132
9.11 Unattended Baggage Detection ................................................................................................... 132
9.12 Object Removal Detection........................................................................................................... 132
9.13 Audio Exception Detection ......................................................................................................... 133
9.14 Sudden Scene Change Detection ................................................................................................. 134
9.15 Defocus Detection ....................................................................................................................... 134
9.16 PIR Alarm ................................................................................................................................... 134
Chapter 10 VCA Search ...................................................................................................................... 135
10.1 Face Search ................................................................................................................................. 136
10.2 Behavior Search .......................................................................................................................... 138
10.3 Plate Search ................................................................................................................................. 139
10.4 People Counting .......................................................................................................................... 140
10.5 Heat Map ..................................................................................................................................... 142
Chapter 11 Network Settings .............................................................................................................. 143
11.1 Configuring General Settings ...................................................................................................... 144
11.2 Configuring Advanced Settings ................................................................................................... 146
11.2.1 PPPoE Settings ............................................................................................................... 146
11.2.2 Configuring EZVIZ Cloud P2P ...................................................................................... 146
11.2.3 Configuring DDNS ......................................................................................................... 147
11.2.4 Configuring NTP Server ................................................................................................. 152
11.2.5 Configuring SNMP ......................................................................................................... 153
11.2.6 Configuring Remote Alarm Host .................................................................................... 153
11.2.7 Configuring Multicast ..................................................................................................... 154
11.2.8 Configuring RTSP .......................................................................................................... 154
11.2.9 Configuring Server and HTTP Ports ............................................................................... 155
11.2.10 Configuring Email .......................................................................................................... 155
11.2.11 Configuring NAT ............................................................................................................ 157
11.3 Checking Network Traffic ........................................................................................................... 160
11.4 Configuring Network Detection .................................................................................................. 161
11.4.1 Testing Network Delay and Packet Loss......................................................................... 161
11.4.2 Exporting Network Packet .............................................................................................. 161
11.4.3 Checking the Network Status .......................................................................................... 162
11.4.4 Checking Network Statistics ........................................................................................... 163
Chapter 12 HDD Management............................................................................................................ 165
12.1 Initializing HDDs ........................................................................................................................ 166
12.2 Managing Network HDD ............................................................................................................ 168
User Manual of Network Video Recorder
12
12.3 Managing HDD Group ................................................................................................................ 171
12.3.1 Setting HDD Groups ....................................................................................................... 171
12.3.2 Setting HDD Property ..................................................................................................... 172
12.4 Configuring Quota Mode............................................................................................................. 174
12.5 Checking HDD Status ................................................................................................................. 176
12.6 HDD Detection ............................................................................................................................ 177
12.7 Configuring HDD Error Alarms .................................................................................................. 179
Chapter 13 Camera Settings ............................................................................................................... 180
13.1 Configuring OSD Settings ........................................................................................................... 181
13.2 Configuring Privacy Mask........................................................................................................... 182
13.3 Configuring Video Parameters .................................................................................................... 183
Chapter 14 NVR Management and Maintenance ............................................................................. 184
14.1 Viewing System Information ....................................................................................................... 185
14.2 Searching & Export Log Files ..................................................................................................... 186
14.3 Importing/Exporting IP Camera Info ........................................................................................... 189
14.4 Importing/Exporting Configuration Files .................................................................................... 190
14.5 Upgrading System ....................................................................................................................... 191
14.5.1 Upgrading by Local Backup Device ............................................................................... 191
14.5.2 Upgrading by FTP .......................................................................................................... 191
14.6 Restoring Default Settings ........................................................................................................... 193
Chapter 15 Others ................................................................................................................................ 194
15.1 Configuring RS-232 Serial Port................................................................................................... 195
15.2 Configuring General Settings ...................................................................................................... 196
15.3 Configuring DST Settings ........................................................................................................... 197
15.4 Configuring More Settings for Device Parameters ...................................................................... 198
15.5 Managing User Accounts............................................................................................................. 199
15.5.1 Adding a User ................................................................................................................. 199
15.5.2 Deleting a User ............................................................................................................... 201
15.5.3 Editing a User ................................................................................................................. 202
Chapter 16 Appendix ........................................................................................................................... 204
16.1 Glossary ....................................................................................................................................... 205
16.2 Troubleshooting ........................................................................................................................... 206
16.3 Summary of Changes .................................................................................................................. 212
16.4 List of Compatible IP Cameras .................................................................................................... 214
16.4.1 List of Hikvision IP Cameras .......................................................................................... 214
16.4.2 List of Third-party IP Cameras ....................................................................................... 221
User Manual of Network Video Recorder
13
Chapter 1 Introduction
User Manual of Network Video Recorder
14
1.1 Front Panel
DS-8600NI-E8 Series
Figure 1. 1 DS-8600NI-E8 Series
Table 1. 1 Description of Control Panel Buttons
No.
Name
1
Status
Indicators
ALARM
READY
STATUS
HDD
MODEM
Tx/Rx
GUARD
2
IR Receiver
3
DVD-R/W
4
Alphanumeric Buttons
5
USB Interfaces
6
Composite
Keys
ESC
REC/SHOT
User Manual of Network Video Recorder
15
No.
Name
PLAY/AUTO
ZOOM+
A/FOCUS+
EDIT/IRIS+
MAIN/SPOT/ZOO
M-
F1/ LIGHT
F2/ AUX
MENU/WIPER
PREV/FOCUS-
PTZ/IRIS-
7
Control
Buttons
DIRECTION
ENTER
User Manual of Network Video Recorder
16
No.
Name
8
JOG SHUTTLE Control
9
POWER ON/OFF
DS-7700NI-E4 Series
Figure 1. 2 DS-7700NI-E4 Series
Table 1. 2 Description of Control Panel Buttons
No.
Name
Function Description
1
Status
Indicators
POWER
Turns green when NVR is powered up.
READY
The indicator is green when the device is running normally.
STATUS
The light is green when the IR remote control is enabled;
The light is red when the function of the composite keys (SHIFT)
are used;
The light is out when none of the above condition is met.
ALARM
The light is red when there is an alarm occurring.
HDD
Blinks red when HDD is reading/writing.
Tx/Rx
Blinks green when network connection is functioning normally.
2
DVD-R/W
Slot for DVD-R/W.
3
Control
Buttons
DIRECTION
In menu mode, the direction buttons are used to navigate between
different fields and items and select setting parameters.
User Manual of Network Video Recorder
17
No.
Name
Function Description
In playback mode, the Up and Down buttons are used to speed up
and slow down record playing, and the Left and Right buttons are
used to move the recording 30s forwards or backwards.
In the image setting interface, the up and down button can adjust
the level bar of the image parameters.
In live view mode, these buttons can be used to switch channels.
ENTER
The Enter button is used to confirm selection in menu mode; or
used to check checkbox fields and ON/OFF switch.
In playback mode, it can be used to play or pause the video.
In single-frame play mode, pressing the Enter button will play the
video by a single frame.
In auto sequence view mode, the buttons can be used to pause or
resume auto sequence.
4
Composite
Keys
SHIFT
Switch between the numeric or letter input and functions of the
composite keys. (Input letter or numbers when the light is out;
Realize functions when the light is red.)
1/MENU
Enter numeral “1”;
Access the main menu interface.
2/ABC/F1
Enter numeral “2”;
Enter letters “ABC”;
The F1 button when used in a list field will select all items in the
list.
In PTZ Control mode, it will turn on/off PTZ light and when the
image is zoomed in, the key is used to zoom out.
3/DEF/F2
Enter numeral “3”;
Enter letters “DEF”;
The F2 button is used to change the tab pages.
In PTZ control mode, it zooms in the image.
4/GHI/ESC
Enter numeral “4”;
Enter letters “GHI”;
Exit and back to the previous menu.
5/JKL/EDIT
Enter numeral “5”;
Enter letters “JKL”;
Delete characters before cursor;
Check the checkbox and select the ON/OFF switch;
Start/stop record clipping in playback.
6/MNO/PLAY
Enter numeral “6”;
Enter letters “MNO”;
Playback, for direct access to playback interface.
7/PQRS/REC
Enter numeral “7”;
Enter letters “PQRS”;
Open the manual record interface.
8/TUV/PTZ
Enter numeral “8”;
Enter letters “TUV”;
Access PTZ control interface.
9/WXYZ/PRE
Enter numeral “9”;
User Manual of Network Video Recorder
18
No.
Name
Function Description
V
Enter letters “WXYZ”;
Multi-channel display in live view.
0/A
Enter numeral “0”;
Shift the input methods in the editing text field. (Upper and
lowercase, alphabet, symbols or numeric input).
Double press the button to switch the main and auxiliary output.
5
JOG SHUTTLE Control
Move the active selection in a menu. It will move the selection up
and down.
In Live View mode, it can be used to cycle through different
channels.
In the Playback mode, it can be used to jump 30s
forward/backward in video files.
In PTZ control mode, it can control the movement of the PTZ
camera.
6
POWER ON/OFF
Power on/off switch.
7
USB Interfaces
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
DS-7600NI-E1(E2) Series
Figure 1. 3 DS-7600NI-E1(E2) Series
Table 1. 3 Description of Control Panel Buttons
No.
Name
Description
1
Status
Indicator
Power
Power indicator turns yellow when system is running.
Status
Status indicator blinks red when data is being read from or written
to HDD.
Tx/Rx
Tx/Rx indictor blinks yellow when network connection is
functioning properly.
2
USB Interface
Universal Serial Bus (USB) ports for additional devices such as
USB mouse and USB Hard Disk Drive (HDD).
User Manual of Network Video Recorder
19
1.2 IR Remote Control Operations
The NVR may also be controlled with the included IR remote control, shown in Figure 1. 4.
Batteries (2×AAA) must be installed before operation.
Figure 1. 4 Remote Control
The keys on the remote control closely resemble the ones on the front panel.
Table 1. 4 Description of the Soft Keyboard Icons
No.
Name
Description
1
POWER
Power on/off the device.
2
DEV
Enables/Disables Remote Control.
3
Alphanumeric Buttons
Switch to the corresponding channel in Live view or PTZ Control mode.
Input numbers and characters in Edit mode.
Switch between different channels in the Playback mode.
4
EDIT Button
Edit text fields. When editing text fields, it will also function as a Backspace
button to delete the character in front of the cursor.
User Manual of Network Video Recorder
20
No.
Name
Description
On checkbox fields, pressing the button will check the checkbox.
In PTZ Control mode, the button adjusts the iris of the camera.
In Playback mode, it can be used to generate video clips for backup.
Enter/exit the folder of USB device.
5
A Button
Adjust focus in the PTZ Control menu.
It is also used to switch between input methods (upper and lowercase
alphabet, symbols and numeric input).
6
REC Button
Enter the Manual Record setting menu.
In PTZ control settings, press the button and then you can call a PTZ preset
by pressing Numeric button.
It is also used to turn audio on/off in the Playback mode.
7
PLAY Button
The button is used to enter the All-day Playback mode.
It is also used to auto scan in the PTZ Control menu.
8
INFO Button
Reserved.
9
VOIP Button
Switch between main and spot output.
In PTZ Control mode, it can be used to zoom out the image.
10
MENU Button
Press the button will help you return to the Main menu (after successful
login).
Press and hold the button for 5 seconds will turn off audible key beep.
In PTZ Control mode, the MENU button will start wiper (if applicable).
In Playback mode, it is used to show/hide the control interface.
11
PREV Button
Switch between single screen and multi-screen mode.
In PTZ Control mode, it is used to adjust the focus in conjunction with the
A/FOCUS+ button.
12
DIRECTION Button
Navigate between different fields and items in menus.
In the Playback mode, the Up and Down button is used to speed up and slow
down recorded video. The Left and Right button will select the next and
previous record files.
In Live View mode, these buttons can be used to cycle through channels.
In PTZ control mode, it can control the movement of the PTZ camera.
ENTER Button
Confirm selection in any of the menu modes.
It can also be used to tick checkbox fields.
In Playback mode, it can be used to play or pause the video.
In single-frame Playback mode, pressing the button will advance the video by
a single frame.
13
PTZ Button
In Auto-switch mode, it can be used to stop /start auto switch.
14
ESC Button
Back to the previous menu.
Press for Arming/disarming the device in Live View mode.
15
RESERVED
Reserved for future usage.
16
F1 Button
Select all items on the list when used in a list field.
In PTZ Control mode, it will turn on/off PTZ light (if applicable).
User Manual of Network Video Recorder
21
No.
Name
Description
In Playback mode, it is used to switch between play and reverse play.
17
PTZ Control Buttons
Buttons to adjust the iris, focus and zoom of a PTZ camera.
18
F2 Button
Cycle through tab pages.
In synchronous playback mode, it is used to switch between channels.
Troubleshooting Remote Control:
Make sure you have installed batteries properly in the remote control. And you have to aim the remote
control at the IR receiver in the front panel.
If there is no response after you press any button on the remote, follow the procedure below to troubleshoot.
Steps:
1. Go to Menu > Settings > General > More Settings by operating the front control panel or the mouse.
2. Check and remember NVR ID#. The default ID# is 255. This ID# is valid for all the IR remote controls.
3. Press the DEV button on the remote control.
4. Enter the NVR ID# you set in step 2.
5. Press the ENTER button on the remote.
If the Status indicator on the front panel turns blue, the remote control is operating properly. If the Status indicator
does not turn blue and there is still no response from the remote, please check the following:
1. Batteries are installed correctly and the polarities of the batteries are not reversed.
2. Batteries are fresh and not out of charge.
3. IR receiver is not obstructed.
If the remote still can’t function properly, please change a remote and try again, or contact the device provider.
User Manual of Network Video Recorder
22
1.2 USB Mouse Operation
A regular 3-button (Left/Right/Scroll-wheel) USB mouse can also be used with this NVR. To use a USB mouse:
1. Plug USB mouse into one of the USB interfaces on the front panel of the NVR.
2. The mouse should automatically be detected. If in a rare case that the mouse is not detected, the possible
reason may be that the two devices are not compatible, please refer to the recommended the device list from
your provider.
The operation of the mouse:
Table 1. 5 Description of the Mouse Control
Name
Action
Description
Left-Click
Single-Click
Live view: Select channel and show the quick set menu.
Menu: Select and enter.
Double-Click
Live view: Switch between single-screen and multi-screen.
Click and Drag
PTZ control: pan, tilt and zoom.
Video tampering, privacy mask and motion detection: Select target area.
Digital zoom-in: Drag and select target area.
Live view: Drag channel/time bar.
Right-Click
Single-Click
Live view: Show menu.
Menu: Exit current menu to upper level menu.
Scroll-Wheel
Scrolling up
Live view: Previous screen.
Menu: Previous item.
Scrolling down
Live view: Next screen.
Menu: Next item.
User Manual of Network Video Recorder
23
1.3 Input Method Description
Figure 1. 5 Soft Keyboard (1)
Figure 1. 6 Soft Keyboard (2)
Description of the buttons on the soft keyboard:
Table 1. 6 Description of the Soft Keyboard Icons
Figure 1. 7
Icon
Description
Icon
Description
~
Number
~
English letter
Lowercase/Uppercase
Backspace
Switch the keyboard
Space
Positioning the cursor
Exit
Symbols
Reserved
User Manual of Network Video Recorder
24
1.4 Rear Panel
The rear panel vaires according to different models.
DS-8600NI-E8, DS-7700NI-E4 and DS-7700NI-E4/P Series
Figure 1. 8 DS-8600NI-E8 and DS-7700NI-E4 Series
Figure 1. 9 DS-7700NI-E4/P Series
Table 1. 7 Description of Rear Panel Interfaces
No.
Item
Description
1
LAN Interface
1 network interface provided for DS-7700NI-E4/P and 2 network
interfaces for DS-7700NI-E4 and DS-8600NI-E8.
2
AUDIO OUT
RCA connector for audio output.
3
LINE IN
RCA connector for audio input.
4
HDMI
TM
HDMI
TM
video output connector.
5
USB 3.0 interface
Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).
6
RS-232 Interface
Connector for RS-232 devices.
7
VGA
DB9 connector for VGA output. Display local video output and menu.
8
RS-485 Interface
Half-duplex connector for RS-485 devices.
9
ALARM IN
Connector for alarm input.
ALARM OUT
Connector for alarm output.
10
GROUND
Ground (needs to be connected when NVR starts up).
11
AC 100V ~ 240V
AC 100V ~ 240V power supply.
12
Power Switch
Switch for turning on/off the device.
13
Network Interfaces with
Network interfaces for the cameras and to provide power over Ethernet.
User Manual of Network Video Recorder
25
No.
Item
Description
PoE function (supported
by DS-7700NI-E4/P)
DS-7600NI-E1, DS-7600NI-E1/4N, DS-7600NI-E2 and DS-7600NI-E2/8N Series
Figure 1. 10 DS-7600NI-E1/E2 Series
Figure 1. 11 DS-7600NI-E1/4N Series
Figure 1. 12 DS-7600NI-E2/8N Series
Table 1. 8 Description of Rear Panel Interfaces
No.
Item
Description
1
Power Supply
DC 12V power supply.
2
Audio In
RCA connector for audio input.
3
HDMI
TM
Interface
HDMI
TM
video output connector.
4
LAN Network Interface
1 10 /100 /1000 Mbps self-adaptive Ethernet interface
5
Audio Out
RCA connector for audio output.
6
VGA Interface
DB9 connector for VGA output. Display local video output and menu.
7
USB Interface
Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).
8
Ground
Ground (needs to be connected when NVR starts up).
9
Power Switch
Switch for turning on/off the device.
10
Network Interfaces with
built-in switch function
Built-in switch network interfaces for the cameras. (Supported by
DS-7600NI-E1/4N and DS-7600NI-E2/8N).
User Manual of Network Video Recorder
26
DS-7600NI-E1/4P and DS-7600NI-E2/8P Series
Figure 1. 13 DS-7600NI-E1/4P Series
Figure 1. 14 DS-7600NI-E2/8P Series
Table 1. 9 Description of Rear Panel Interfaces
No.
Item
Description
1
Power Supply
DC 48V power supply for DS-7600NI-E1/4P and AC 100~240V for
DS-7600NI-E2/8P.
2
Audio In
RCA connector for audio input.
3
HDMI
TM
Interface
HDMI
TM
video output connector.
4
LAN Network Interface
1 10 /100 /1000 Mbps self-adaptive Ethernet interface
5
Audio Out
RCA connector for audio output.
6
VGA Interface
DB9 connector for VGA output. Display local video output and menu.
7
USB Interface
Universal Serial Bus (USB) ports for additional devices such as USB
mouse and USB Hard Disk Drive (HDD).
8
Ground
Ground (needs to be connected when NVR starts up).
9
Power Switch
Switch for turning on/off the device.
10
Network Interfaces with
PoE function
Network interfaces for the cameras and to provide power over Ethernet.
User Manual of Network Video Recorder
27
Chapter 2 Getting Started
User Manual of Network Video Recorder
28
2.1 Starting Up and Shutting Down the NVR
Purpose:
Proper startup and shutdown procedures are crucial to expanding the life of the NVR.
Before you start:
Check that the voltage of the extra power supply is the same with the NVR’s requirement, and the ground
connection is working properly.
Starting up the NVR:
Steps:
1. Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device. The Power indicator LED on
the front panel should be red, indicating the device gets the power supply.
2. Turn on the power switch on the rear panel if the device starts up for the first time, or press the button
on the front panel. The Power indicator LED should turn blue indicating that the unit begins to start up.
3. After startup, the Power indicator LED remains blue. A splash screen with the status of the HDD appears on
the monitor. The row of icons at the bottom of the screen shows the HDD status. ‘X’ means that the HDD is
not installed or cannot be detected.
Shutting down the NVR
There are two proper ways to shut down the NVR.
OPTION 1: By Standard shutdown
Steps:
1. Enter the Shutdown menu.
Menu > Shutdown
Figure 2. 1 Shutdown Menu
2. Click the Shutdown button.
3. Click the Yes button.
4. For the DS-7600NI-E1(E2) series, turn off the power switch on the rear panel when the attention pops up.
Figure 2. 2 Shutdown Attention
User Manual of Network Video Recorder
29
OPTION 2: By operating the front panel (supported by DS-8600NI-E8 and DS-7700NI-E4(/P) series)
Steps:
1. Press and hold the button on the front panel for 3 seconds.
2. Enter the administrator’s username and password in the dialog box for authentication if required.
3. Click the Yes button.
Do not press the button again when the system is shutting down.
Rebooting the NVR
In the Shutdown menu, you can also reboot the NVR.
Steps:
1. Enter the Shutdown menu by clicking Menu > Shutdown.
2. Click the Logout button to lock the NVR or the Reboot button to reboot the NVR.
User Manual of Network Video Recorder
30
2.2 Setting Admin Password
Purpose:
For the first-time access, you need to activate the device by setting an admin password. No operation is allowed
before activation.
Steps:
1. Input the same password in the text field of Create New Password and Confirm New Password.
Figure 2. 3 Settings Admin Password
STRONG PASSWORD RECOMMENDED We highly recommend you create a strong
password of your own choosing (using a minimum of 8 characters, including upper case letters,
lower case letters, numbers, and special characters) in order to increase the security of your
product. And we recommend you reset your password regularly, especially in the high security
system, resetting the password monthly or weekly can better protect your product.
2. Click OK to save the password and activate the device.
For the old version device, if you update it to the new version, the following dialog box will pop up once the
device starts up. You can click YES and follow the wizard to set a strong password.
Figure 2. 4 Warning
User Manual of Network Video Recorder
31
2.3 Using the Wizard for Basic Configuration
Purpose:
After admin password is set, the setup wizard pops up automatically. It can walk you through some basic settings
of the NVR.
Figure 2. 5 Start Wizard Interface
Steps:
1. If you don’t want to use the setup wizard at that moment, click the Exit button. You can also choose to use
the Setup Wizard next time by leaving the “Start wizard when the device starts?” checkbox checked.
2. Click the Next button to enter the Date and Time Settings interface.
Figure 2. 6 Date and Time Settings
3. After the time settings, click Next button which takes you back to the Basic Network Setup Wizard
interface.
User Manual of Network Video Recorder
32
Figure 2. 7 Network Configuration (DS-8600NI-E8 and DS-7700NI-E4)
The dual-NIC network 10 /100/1000 Mbps self-adaptive Ethernet interfaces are provided for the
DS-8600NI-E8 and DS-7700NI-E4 series NVR;one 10 /100 Mbps self-adaptive Ethernet interface for
DS-7604/7608NI-E1(E2) series NVR; and one 10 /100/1000 Mbps self-adaptive Ethernet interface for
other models.
For the models have the PoE or built-in switch network interfaces, including DS-7600NI-E1(E2)/N,
DS-7600NI-E1(E2)/P and DS-7700NI-E4/P series NVR, the internal NIC IPv4 address should be
configured for the cameras connecting to the PoE or built-in switch network interface of the NVR.
4. Click Next button after you configured the basic network parameters. Then you will enter the EZVIZ Cloud
P2P interface. Configure the EZVIZ Cloud P2P according to your need.
Figure 2. 8 Advanced Network Parameters
User Manual of Network Video Recorder
33
5. Click Next button to enter the Advanced Network Parameter interface. You can enable PPPoE, enable
DDNS and set other ports according to your need.
Figure 2. 9 Advanced Network Parameters
6. After configuration finishes, click Next button to enter HDD Management interface.
Figure 2. 10 HDD Management
7. To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
8. Click Next button to enter the IP Camera Management interface.
9. Click Search to search the online IP Camera and the Security status shows whether it is active or inactive.
Before adding the camera, make sure the IP camera to be added is in active status.
If the camera is in inactive status, you can click the inactive icon of the camera to set the password to
activate it. You can also select multiple cameras from the list and click the One-touch Activate to activate
the cameras in batch.
Click the Add to add the camera.
User Manual of Network Video Recorder
34
Figure 2. 11 IP Camera Management
10. Click Next button. Configure the recording for the searched IP Cameras.
Figure 2. 12 Record Settings
11. Click OK to complete the startup Setup Wizard.
User Manual of Network Video Recorder
35
2.4 Login and Logout
2.4.1 User Login
Purpose:
If NVR has logged out, you must login the device before operating the menu and other functions.
Steps:
1. Select the User Name in the dropdown list.
Figure 2. 13 Login Interface
2. Input Password.
3. Click OK to log in.
The device gets locked for 60 seconds if the admin user performs 7 failed password attempts (5 attempts for the
guest/operator).
Figure 2. 14 User Account Protection
2.4.2 User Logout
Purpose:
After logging out, the monitor turns to the live view mode and if you want to do some operation, you need to enter
user name and password tog in again.
Steps:
1. Enter the Shutdown menu.
Menu>Shutdown
User Manual of Network Video Recorder
36
Figure 2. 15 Logout
2. Click Logout.
After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name
and password to unlock the system.
User Manual of Network Video Recorder
37
2.5 Adding and Connecting the IP Cameras
2.5.1 Activating the IP Camera
Purpose:
Before adding the camera, make sure the IP camera to be added is in active status.
Steps:
1. Select the Add IP Camera option from the right-click menu in live view mode or click Menu> Camera>
Camera to enter the IP camera management interface.
For the IP camera detected online in the same network segment, the Security status shows whether it is
active or inactive.
Figure 2. 16 IP Camera Management Interface
2. Click the inactive icon of the camera to enter the following interface to activate it. You can also select
multiple cameras from the list and click the One-touch Activate to activate the cameras in batch.
Figure 2. 17 Activate the Camera
3. Set the password of the camera to activate it.
Use Admin Password: when you check the checkbox, the camera (s) will be configured with the same
User Manual of Network Video Recorder
38
admin password of the operating NVR.
Figure 2. 18 Set New Password
Create New Password: If the admin password is not used, you must create the new password for the camera
and confirm it.
STRONG PASSWORD RECOMMENDED We highly recommend you create a strong
password of your own choosing (using a minimum of 8 characters, including upper case letters,
lower case letters, numbers, and special characters) in order to increase the security of your
product. And we recommend you reset your password regularly, especially in the high security
system, resetting the password monthly or weekly can better protect your product.
4. Click OK to finish the acitavting of the IP camera. And the security status of camera will be changed to
Active.
2.5.2 Adding the Online IP Cameras
Purpose:
The main function of the NVR is to connect the network cameras and record the video got from it. So before you
can get a live view or record of the video, you should add the network cameras to the connection list of the device.
Before you start:
Ensure the network connection is valid and correct. For detailed checking and configuring of the network, please
see Chapter Checking Network Traffic and Chapter Configuring Network Detection.
OPTION 1:
Steps:
1. Click to select an idle window in the live view mode.
2. Click the icon in the center of the windw to pop up the adding IP camera interface.
User Manual of Network Video Recorder
39
Figure 2. 19 Quick Adding IP Camera Interface
3. Select the detected IP camera and click the Add button to add it directly, and you can click the Search button
to refresh the online IP camera manually.
Or you can choose to custom add the IP camera by editing the parameters in the corresponding textfiled and
then click the Add button to add it.
OPTION 2:
Steps:
1. Select the Add IP Camera option from the right-click menu in live view mode or click Menu> Camera>
Camera to enter the IP camera management interface.
Figure 2. 20 Adding IP Camera Interface
2. The online cameras with same network segment will be detected and displayed in the camera list.
3. Select the IP camera from the list and click the button to add the camera. Or you can click the
One-touch Adding button to add all cameras from the list.
User Manual of Network Video Recorder
40
4. (For the encoders with multiple channels only) check the checkbox of Channel Port in the pop-up window, as
shown in the following figure, and click OK to add multiple channels.
Figure 2. 21 Selecting Multiple Channels
OPTION 3:
Steps:
1) On the IP Camera Management interface, click the Custom Adding button to pop up the Add IP Camera
(Custom) interface.
Figure 2. 22 Custom Adding IP Camera Interface
2) You can edit the IP address, protocol, management port, and other information of the IP camera to be
added.
If the IP camera to add has not been actiavted, you can activate it from the IP camera list on the
camera management interface.
3) (Optional) Check the checkbox of Continue to Add to add other IP cameras.
4) Click Add to add the camera.
For the successfully added IP cameras, the Security status shows the security level of the password of camera:
User Manual of Network Video Recorder
41
strong password, weak password and risk password.
Figure 2. 23 Successfully Added IP Cameras
Table 2. 1 Explanation of the icons
Icon
Explanation
Icon
Explanation
Edit basic parameters of the camera
Add the detected IP camera.
The camera is disconnected; you can
click the icon to get the exception
information of camera.
Delete the IP camera
Play the live video of the connected
camera.
Advanced settings of the camera.
Upgrade the connected IP camera.
Security
Show the security status of the
camera to be active/inactive or the
password strength (strong/weak/risk)
2.5.3 Editing the Connected IP cameras and Configuring
Customized Protocols
After the adding of the IP cameras, the basic information of the camera lists in the page, you can configure the
basic setting of the IP cameras.
Steps:
1. Click the icon to edit the parameters; you can edit the IP address, protocol and other parameters.
User Manual of Network Video Recorder
42
Figure 2. 24 Edit the Parameters
Channel Port: If the connected device is an encoding device with multiple channels, you can choose the
channel to connect by selecting the channel port No. in the dropdown list.
2. Click OK to save the settings and exit the editing interface.
To edit advanced parameters:
1. Drag the horizontal scroll bar to the right side and click the icon.
Figure 2. 25 Network Configuration of the Camera
2. You can edit the network information and the password of the camera.
User Manual of Network Video Recorder
43
Figure 2. 26 Password Configuration of the Camera
3. Click OK to save the settings and exit the interface.
Configuring the customized protocols
Purpose:
To connect the network cameras which are not configured with the standard protocols, you can configure the
customized protocols for them.
Steps:
1. Click the Protocol button in the custom adding IP camera interface to enter the protocol management
interface.
Figure 2. 27 Protocol Management Interface
There are 16 customized protocols provided in the system, you can edit the protocol name; and choose
whether to enable the sub-stream.
2. Choose the protocol type of transmission and choose the transfer protocols.
Before customizing the protocol for the network camera, you have to contact the manufacturer of the network
camera to consult the URL (uniform resource locator) for getting main stream and sub-stream.
The format of the URL is: [Type]://[IP Address of the network camera]:[Port]/[Path].
User Manual of Network Video Recorder
44
Example: rtsp://192.168.1.55:554/ch1/main/av_stream.
Protocol Name: Edit the name for the custom protocol.
Enable Substream: If the network camera does not support sub-stream or the sub-stream is not needed
leave the checkbox empty.
Type: The network camera adopting custom protocol must support getting stream through standard RTSP.
Transfer Protocol: Select the transfer protocol for the custom protocol.
Port: Set the port No. for the custom protocol.
Path: Set the resource path for the custom protocol. E.g., ch1/main/av_stream.
The protocol type and the transfer protocols must be supported by the connected network camera.
After adding the customized protocols, you can see the protocol name is listed in the dropdown list, please refer to
Figure 2. 28.
Figure 2. 28 Protocol Setting
3. Choose the protocols you just added to validate the connection of the network camera.
2.5.4 Editing IP Cameras Connected to the PoE Interfaces
This chapter is only applicable for DS-7600/7700NI-SP series NVR.
The PoE interfaces enables the NVR system to pass electrical power safely, along with data, on Ethernet cabling to
the connected network cameras.
The DS-7600/7700NI-SP series NVR provides up to 16 PoE interfaces which can connect to 16 network cameras
directly; and if you disable the PoE interface, you can also connect to the online network cameras. And the PoE
interface supports the Plug-and-Play function.
Example:
As for 7608/7708NI-SP NVR, when you want to connect 2 online cameras and connect 6 network cameras via
PoE interfaces, you must disable 2 PoE interfaces in the Edit IP Camera menu.
To add Cameras for NVR supporting PoE function:
Before you start:
User Manual of Network Video Recorder
45
Connect the network cameras via the PoE interfaces.
Steps:
1. Enter the Camera Management interface.
Menu> Camera> Camera
Figure 2. 29 List of Connected Cameras
The cameras connecting to the PoE interface cannot be deleted in this menu.
2. Click the button, and select the Adding Method in the drop-down list.
Plug-and-Play: It means that the camera is connected to the PoE interface, so in this case, the
parameters of the camera can’t be edited. The IP address of the camera can only be edited in the Network
Configuration interface, see Chapter 9.1 Configuring General Settings for detailed information.
Figure 2. 30 Edit IP Camera Interface - Plug-and-Play
Manual: You can disable the PoE interface by selecting the manual while the current channel can be
used as a normal channel and the parameters can also be edited.
Input the IP address, the user name and password of administrator manually, and click OK to add the IP
camera.
User Manual of Network Video Recorder
46
Figure 2. 31 Edit IP Camera Interface - Manual
User Manual of Network Video Recorder
47
Chapter 3 Live View
User Manual of Network Video Recorder
48
3.1 Introduction of Live View
Live view shows you the video image getting from each camera in real time. The NVR automatically enters Live
View mode when powered on. It is also at the very top of the menu hierarchy, thus pressing the ESC many times
(depending on which menu you’re on) brings you to the Live View mode.
Live View Icons
In the live view mode, there are icons at the upper-right of the screen for each channel, showing the status of the
record and alarm in the channel, so that you can know whether the channel is recorded, or whether there are alarms
occur as soon as possible.
Table 3. 1 Description of Live View Icons
Icons
Description
Alarm (video loss, video tampering, motion detection, sensor alarm or VCA alarm)
Record (manual record, continuous record, motion detection , sensor alarm or VCA alarm
triggered record)
Alarm & Record
Event/Exception (motion detection, sensor alarm, VCA alarm or exception information,
appears at the lower-left corner of the screen. Please refer to Chapter 8.6 Setting Alarm
Response Actions for details.)
User Manual of Network Video Recorder
49
3.2 Operations in Live View Mode
In live view mode, there are many functions provided. The functions are listed below.
Single Screen: showing only one screen on the monitor.
Multi-screen: showing multiple screens on the monitor simultaneously.
Auto-switch: the screen is auto switched to the next one. And you must set the dwell time for each screen on
the configuration menu before enabling the auto-switch.
Menu > Configuration > Live View > Dwell Time.
Start Recording: continuous record and motion detection record are supported.
Output Mode: select the output mode to Standard, Bright, Gentle or Vivid.
Add IP Camera: the shortcut to the IP camera management interface.
Playback: playback the recorded videos for current day.
3.2.1 Front Panel Operation on Live View
The front panel operation is supported by DS-8600NI-E8 and DS-7700NI-E4(/P) models only.
Table 3. 2 Front Panel Operation in Live View
Functions
Front Panel Operation
Show single screen
Press the corresponding Alphanumeric button. E.g. Press 2 to display only the
screen for channel 2.
Show multi-screen
Press the PREV/FOCUS- button.
Manually switch screens
Next screen: right/down direction button.
Previous screen: left/up direction button.
Auto-switch
Press Enter button.
Playback
Press Play button.
3.2.2 Using the Mouse in Live View
Table 3. 3 Mouse Operation in Live View
Name
Description
Common Menu
Quick access to the sub-menus which you frequently visit.
Menu
Enter the main menu of the system by right clicking the mouse.
Single Screen
Switch to the single full screen by choosing channel number from the dropdown
list.
Multi-screen
Adjust the screen layout by choosing from the dropdown list.
Previous Screen
Switch to the previous screen.
Next Screen
Switch to the next screen.
Start/Stop Auto-switch
Enable/disable the auto-switch of the screens.
User Manual of Network Video Recorder
50
Name
Description
Start Recording
Start continuous recording or motion detection recording of all channels.
Add IP Camera
Enter the IP Camera Management interface, and manage the cameras.
Playback
Enter the playback interface and start playing back the video of the selected
channel immediately.
Output Mode
Four modes of output supported, including Standard, Bright, Gentle and Vivid.
The dwell time of the live view configuration must be set before using Start Auto-switch.
If the corresponding camera supports intelligent function, the Reboot Intelligence option is included when
right-clicking mouse on this camera.
Figure 3. 1 Right-click Menu
The right-click menu varies according to different models, please refer to the actual GUI menu of the device.
3.2.3 Quick Setting Toolbar in Live View Mode
On the screen of each channel, there is a quick setting toolbar which shows when you single click the mouse in the
corresponding screen.
Figure 3. 2 Quick Setting Toolbar
Table 3. 4 Description of Quick Setting Toolbar Icons
Icon
Description
Icon
Description
Icon
Description
/
Enable/Disable
Manual Record
Instant Playback
/
Mute/Audio on
User Manual of Network Video Recorder
51
Icon
Description
Icon
Description
Icon
Description
PTZ Control
Digital Zoom
Image Settings
Face Detection
Live View
Strategy
Information
Close
Instant Playback only shows the record in last five minutes. If no record is found, it means there is no record
during the last five minutes.
Digital Zoom can zoom in the selected area to the full screen. You can left-click and draw to select the area
to zoom in, as shown in Figure 3. 3.
Figure 3. 3 Digital Zoom
Image Settings icon can be selected to enter the Image Settings menu.
Figure 3. 4 Image Settings- Preset
User Manual of Network Video Recorder
52
You can set the image parameters like brightness, contrast, saturation and hue.
Figure 3. 5 Image Settings- Customize
Live View Strategy can be selected to set strategy, including Real-time, Balanced, Fluency.
Figure 3. 6 Live View Strategy
Move the mouse onto the icon to show the real-time stream information, including the frame rate, bitrate,
resolution and stream type.
Figure 3. 7 Information
User Manual of Network Video Recorder
53
3.3 Adjusting Live View Settings
Purpose:
Live View settings can be customized according to different needs. You can configure the output interface, dwell
time for screen to be shown, mute or turning on the audio, the screen number for each channel, etc.
Steps:
1. Enter the Live View Settings interface.
Menu > Configuration > Live View
Figure 3. 8 Live View-General
The settings available in this menu include:
Video Output Interface: Designates the output to configure the settings for, and only VGA/ HDMI
TM
is
selectable by default.
Live View Mode: Designates the display mode to be used for Live View.
Dwell Time: The time in seconds to dwell between switching of channels when enabling auto-switch in
Live View.
Enable Audio Output: Enables/disables audio output for the selected video output.
Volume: Adjust the volume of live view, playback and two-way audio for the selected output interface.
Event Output: Designates the output to show event video.
Full Screen Monitoring Dwell Time: The time in seconds to show alarm event screen.
2. Setting Cameras Order
Figure 3. 9 Live View- Camera Order
User Manual of Network Video Recorder
54
1) Select a View mode in .
2) Select the small window, and double-click on the channel number to display the channel on the
window.
If you do not want the camera to be displayed on the live view interface, click the corresponding
to stop it.
You can also click button to start live view for all the channels and click to stop all the live
view.
3) Click the Apply button to save the setting.
3.4 Channel-zero Encoding
Purpose:
Sometimes you need to get a remote view of many channels in real time from web browser or CMS (Client
Management System) software, in order to decrease the bandwidth requirement without affecting the image quality,
channel-zero encoding is supported as an option for you.
Steps:
1. Enter the Live View Settings interface.
Menu > Configuration > Live View
2. Select the Channel-Zero Encoding tab.
Figure 3. 10 Live View- Channel-Zero Encoding
3. Check the checkbox after Enable Channel Zero Encoding.
4. Configure the Frame Rate, Max. Bitrate Mode and Max. Bitrate.
After you set the Channel-Zero encoding, you can get a view in the remote client or web browser of 16 channels in
one screen.
User Manual of Network Video Recorder
55
Chapter 4 PTZ Controls
User Manual of Network Video Recorder
56
4.1 Configuring PTZ Settings
Purpose:
Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before
you control the PTZ camera.
Steps:
1. Enter the PTZ Settings interface.
Menu > Camera > PTZ
Figure 4. 1 PTZ Settings
2. Click the RS-485 Settings button to set the RS-485 parameters.
Figure 4. 2 PTZ- General
3. Choose the camera for PTZ setting in the Camera dropdown list.
4. Enter the parameters of the PTZ camera.
User Manual of Network Video Recorder
57
All the parameters should be exactly the same as the PTZ camera parameters.
5. Click Apply button to save the settings.
User Manual of Network Video Recorder
58
4.2 Setting PTZ Presets, Patrols & Patterns
Before you start:
Please make sure that the presets, patrols and patterns should be supported by PTZ protocols.
4.2.1 Customizing Presets
Purpose:
Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place.
Steps:
1. Enter the PTZ Control interface.
Menu > Camera > PTZ
Figure 4. 3 PTZ Settings
2. Use the directional button to wheel the camera to the location where you want to set preset; and the zoom
and focus operations can be recorded in the preset as well.
3. Enter the preset No. (1~255) in the preset text field, and click the Set button to link the location to the preset.
Repeat the steps2-3 to save more presets.
You can click the Clear button to clear the location information of the preset, or click the Clear All button
to clear the location information of all the presets.
4.2.2 Calling Presets
Purpose:
This feature enables the camera to point to a specified position such as a window when an event takes place.
Steps:
1. Click the button PTZ in the lower-right corner of the PTZ setting interface;
User Manual of Network Video Recorder
59
Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar, or
select the PTZ option in the right-click menu to show the PTZ control panel.
2. Choose Camera in the dropdown list.
3. Click the button to show the general settings of the PTZ control.
Figure 4. 4 PTZ Panel - General
4. Click to enter the preset No. in the corresponding text field.
5. Click the Call Preset button to call it.
4.2.3 Customizing Patrols
Purpose:
Patrols can be set to move the PTZ to different key points and have it stay there for a set duration before moving
on to the next key point. The key points are corresponding to the presets. The presets can be set following the steps
above in Customizing Presets.
Steps:
1. Enter the PTZ Control interface.
Menu > Camera > PTZ
Figure 4. 5 PTZ Settings
2. Select patrol No. in the drop-down list of patrol.
User Manual of Network Video Recorder
60
3. Click the Set button to add key points for the patrol.
Figure 4. 6 Key point Configuration
4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of
patrol. The key point is corresponding to the preset. The Key Point No. determines the order at which the
PTZ will follow while cycling through the patrol. The Duration refers to the time span to stay at the
corresponding key point. The Speed defines the speed at which the PTZ will move from one key point to the
next.
5. Click the Add button to add the next key point to the patrol, and you can click the OK button to save the key
point to the patrol.
You can delete all the key points by clicking the Clear button for the selected patrol, or click the Clear All
button to delete all the key pints for all patrols.
4.2.4 Calling Patrols
Purpose:
Calling a patrol makes the PTZ to move according the predefined patrol path.
Steps:
1. Click the button PTZ in the lower-right corner of the PTZ setting interface;
Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar, or
select the PTZ option in the right-click menu to show the PTZ control panel.
2. Click the button to show the general settings of the PTZ control.
Figure 4. 7 PTZ Panel - General
3. Select a patrol in the dropdown list and click the Call Patrol button to call it.
4. You can click the Stop Patrol button to stop calling it.
User Manual of Network Video Recorder
61
4.2.5 Customizing Patterns
Purpose:
Patterns can be set by recording the movement of the PTZ. You can call the pattern to make the PTZ movement
according to the predefined path.
Steps:
1. Enter the PTZ Control interface.
Menu > Camera > PTZ
Figure 4. 8 PTZ Settings
2. Choose pattern number in the dropdown list.
3. Click the Start button and click corresponding buttons in the control panel to move the PTZ camera, and
click the Stop button to stop it.
The movement of the PTZ is recorded as the pattern.
4.2.6 Calling Patterns
Purpose:
Follow the procedure to move the PTZ camera according to the predefined patterns.
Steps:
1. Click the button PTZ in the lower-right corner of the PTZ setting interface;
Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar, or
select the PTZ option in the right-click menu to show the PTZ control panel.
2. Click the button to show the general settings of the PTZ control.
User Manual of Network Video Recorder
62
Figure 4. 9 PTZ Panel - General
3. Click the Call Pattern button to call it.
4. Click the Stop Pattern button to stop calling it.
4.2.7 Customizing Linear Scan Limit
Purpose:
The Linear Scan can be enabled to trigger the scan in the horizantal direction in the predefined range.
This function is supported by some certain models.
Steps:
1. Enter the PTZ Control interface.
Menu > Camera > PTZ
Figure 4. 10 PTZ Settings
2. Use the directional button to wheel the camera to the location where you want to set the limit, and click the
Left Limit or Right Limit button to link the location to the corresponding limit.
User Manual of Network Video Recorder
63
The speed dome starts linear scan from the left limit to the right limit, and you must set the left limit on
the left side of the right limit, as well the angle from the left limit to the right limit should be no more
than 180º.
4.2.8 Calling Linear Scan
Before operating this function, make sure the connected camera supports the linear scan and is in HIKVISION
protocol.
Purpose:
Follow the procedure to call the linear scan in the predefined scan range.
Steps:
1. Click the button PTZ in the lower-right corner of the PTZ setting interface;
Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar to
enter the PTZ setting menu in live view mode.
2. Click the button to show the one-touch function of the PTZ control.
Figure 4. 11 PTZ Panel - One-touch
3. Click Linear Scan button to start the linear scan and click the Linear Scan button again to stop it.
You can click the Restore button to clear the defined left limit and right limit data and the dome needs to
reboot to make settings take effect.
4.2.9 One-touch Park
Before operating this function, make sure the connected camera supports the linear scan and is in HIKVISION
protocol.
Purpose:
For some certain model of the speed dome, it can be configured to start a predefined park action (scan, preset,
User Manual of Network Video Recorder
64
patrol and etc.) automatically after a period of inactivity (park time).
Steps:
1. Click the button PTZ in the lower-right corner of the PTZ setting interface;
Or press the PTZ button on the front panel or click the PTZ Control icon in the quick setting bar to
enter the PTZ setting menu in live view mode.
2. Click the button to show the one-touch function of the PTZ control.
Figure 4. 12 PTZ Panel - One-touch
3. There are 3 one-touch park types selectable, click the corresponding button to activate the park action.
Park (Quick Patrol): The dome starts patrol from the predefined preset 1 to preset 32 in order after the park
time. The undefined preset will be skipped.
Park (Patrol 1): The dome starts move according to the predefined patrol 1 path after the park time.
Park (Preset 1): The dome moves to the predefined preset 1 location after the park time.
The park time can only be set through the speed dome configuration interface, by default the value is 5s.
4. Click the button again to inactivate it.
User Manual of Network Video Recorder
65
4.3 PTZ Control Panel
To enter the PTZ control panel, there are two ways supported.
OPTION 1:
In the PTZ settings interface, click the PTZ button on the lower-right corner which is next to the Back button.
OPTION 2:
In the Live View mode, you can press the PTZ Control button on the front panel or on the remote control, or
choose the PTZ Control icon , or select the PTZ option in the right-click menu.
Click the Configuration button on the control panel, and you can enter the PTZ Settings interface.
In PTZ control mode, the PTZ panel will be displayed when a mouse is connected with the device. If no
mouse is connected, the icon appears in the lower-left corner of the window, indicating that this
camera is in PTZ control mode.
Figure 4. 13 PTZ Panel
Table 4. 1 Description of the PTZ panel icons
Icon
Description
Icon
Description
Icon
Description
Direction button and
the auto-cycle button
Zoom+, Focus+,
Iris+
Zoom-, Focus-, Iris-
The speed of the
PTZ movement
Light on/off
Wiper on/off
3D-Zoom
Image Centralization
Menu
Switch to the PTZ
control interface
Switch to the
one-touch control
interface
Switch to the general
settings interface
Previous item
Next item
Start pattern / patrol
Stop the patrol /
pattern movement
Exit
Minimize windows
User Manual of Network Video Recorder
66
Chapter 5 Recording Settings
User Manual of Network Video Recorder
67
5.1 Configuring Parameters
Purpose:
By configuring the parameters you can define the parameters which affect the image quality, such as the
transmission stream type, the resolution and so on.
Before you start:
1. Make sure that the HDD has already been installed. If not, please install a HDD and initialize it. (Menu >
HDD > General)
Figure 5. 1 HDD- General
2. Check the storage mode of the HDD.
1) Click Advanced to check the storage mode of the HDD.
2) If the HDD mode is Quota, please set the maximum record capacity For detailed information, see
Chapter 12.4 Configuring Quota Mode.
3) If the HDD mode is Group, you should set the HDD group. For detailed information, see Chapter
Configuring HDD Group for Recording.
Figure 5. 2 HDD- Advanced
Steps:
1. Enter the Record settings interface to configure the recording parameters:
Menu > Record > Parameters
Figure 5. 3 Recording Parameters
User Manual of Network Video Recorder
68
2. Parameters Setting for Recording
1) Select Record tab page to configure. You can configure the stream type, the resolution, and other
parameters on your demand.
Enable H.264+ Mode: check the checkbox to enable. Once enabled, the Max. Bitrate Mode,
Max. Bitrate(Kbps) and Max. Bitrate Range Recommend are not configurable. Enabling it
helps to ensure the high video quality with a lowered bitrate.
The function is only available for IP cameras which support H.264+ stream.
2) Click the More Settings button to set the advanced parameters for recording and then click OK button to
finish editing.
Figure 5. 4 Recording Parameters-More Settings
Pre-record: The time you set to record before the scheduled time or event. For example, when an
alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the camera records
it at 9:59:55.
Post-record: The time you set to record after the event or the scheduled time. For example, when an
alarm triggered the recording ends at 11:00, if you set the post-record time as 5 seconds, it records till
11:00:05.
Expired Time: The expired time is the longest time for a record file to be kept in the HDD, if the
deadline is reached, the file will be deleted. You can set the expired time to 0, and then the file will
not be deleted. The actual keeping time for the file should be determined by the capacity of the HDD.
Redundant Record: Enabling redundant record means you save the recording files in the redundant
HDD. See Chapter Configuring Redundant Recording.
Record Audio: Check the checkbox to enable or disable audio recording.
Video Stream: Main stream and sub-stream are selectable for recording. When you select
sub-stream, you can record for a longer time with the same storage space.
3) Click Apply to save the settings.
The redundant record is to decide whether you want the camera to save the recording files in the
redundant HDD. You must configure the redundant HDD in HDD settings. For detailed information,
see Chapter12.3.2 Setting HDD Property.
The parameters of Main Stream (Event) are read-only.
User Manual of Network Video Recorder
69
3. Parameters Settings for Sub-stream
1) Enter the Sub-stream tab page.
Figure 5. 5 Sub-stream Parameters
2) Configure the parameters of the camera.
3) Click Apply to save the settings.
User Manual of Network Video Recorder
70
5.2 Configuring Recording Schedule
Purpose:
Set the recording schedule, and then the camera automatically starts/stops recording according to the configured
schedule.
Steps:
1. Enter the Record Schedule interface.
Menu > Record > Schedule
2. Configure Record Schedule
1) Select Record Schedule.
Figure 5. 6 Record Schedule
Different recording types are marked in different color icons.
Continous: scheduled recording.
Event: recording triggered by all event triggered alarm.
Motion: recording triggered by motion detection.
Alarm: recording triggered by alarm.
M/A: recording triggered by either motion detection or alarm.
M&A: recording triggered by motion detection and alarm.
2) Choose the camera you want to configure.
3) Select the check box after the Enable Schedule item.
4) Click Edit button or click on the color icon under the edit button and draw the schedule line on the
panel.
Edit the schedule:
I. In the message box, you can choose the day to which you want to set schedule.
User Manual of Network Video Recorder
71
Figure 5. 7 Recording Schedule Interface
You can click the button to set the accurate time of the schedule.
II. To schedule an all-day recording, check the checkbox after the All Day item.
Figure 5. 8 Edit Schedule
III. To arrange other schedule, leave the All Day checkbox blank and set the Start/End time.
Up to 8 periods can be configured for each day. And the time periods cannot be overlapped each other.
IV. Select the record type in the dropdown list.
To enable Motion, Alarm, M | A (motion or alarm), M & A (motion and alarm) and VCA (Video
Content Analysis) triggered recording and capture, you must configure the motion detection
settings, alarm input settings or VCA settings as well. For detailed information, refer to Chapter
8.1, Chapter 8.2 and Chapter 5.5.
The VCA settings are only available to the smart IP cameras.
Repeat the above edit schedule steps to schedule recording for other days in the week. You can click
Copy to enter the Copy to interface to copy the schedule settings to other days
V. Click Apply in the Record Schedule interface to save the settings.
Draw the schedule:
I. Click on the color icons, you can choose the schedule type as continuous or event.
User Manual of Network Video Recorder
72
Figure 5. 9 Draw the Schedule
II. Click the Apply button to validate the settings.
3. (Optional) If the settings can also be used to other channels, click Copy, and then choose the channel to
which you want to copy.
4. Click Apply to save the settings.
User Manual of Network Video Recorder
73
5.3 Configuring Motion Detection Recording
Purpose:
Follow the steps to set the motion detection parameters. In the live view mode, once a motion detection event takes
place, the NVR can analyze it and do many actions to handle it. Enabling motion detection function can trigger
certain channels to start recording, or trigger full screen monitoring, audio warning, notify the surveillance center
and so on. In this chapter, you can follow the steps to schedule a record which triggered by the detected motion.
Steps:
1. Enter the Motion Detection interface.
Menu > Camera > Motion
2. Configure Motion Detection
1) Choose camera you want to configure.
2) Check the checkbox after Enable Motion Detection.
3) Drag and draw the area for motion detection by mouse. If you want to set the motion detection for all the
area shot by the camera, click Full Screen. To clear the motion detection area, click Clear.
Figure 5. 10 Motion Detection- Mask
4) Click Settings, and the message box for channel information pop up.
Figure 5. 11 Motion Detection Handling
5) Select the channels which you want the motion detection event to trigger recording.
6) Click Apply to save the settings.
User Manual of Network Video Recorder
74
7) Click OK to back to the upper level menu.
8) Exit the Motion Detection menu.
3. Edit the Motion Detection Record Schedule. For the detailed information of schedule configuration, see
Chapter 5.2 Configuring Recording Schedule.
User Manual of Network Video Recorder
75
5.4 Configuring Alarm Triggered Recording
Purpose:
Follow the procedure to configure alarm triggered recording.
Steps:
1. Enter the Alarm setting interface.
Menu > Configuration > Alarm
Figure 5. 12 Alarm Settings
2. Click Alarm Input tab and set the alarm parameters.
Figure 5. 13 Alarm Settings- Alarm Input
1) Select Alarm Input number and configure alarm parameters.
2) Choose N.O (normally open) or N.C (normally closed) for alarm type.
3) Check the checkbox for Enable.
4) Click Settings.
User Manual of Network Video Recorder
76
Figure 5. 14 Alarm Settings
5) Choose the alarm triggered recording channel.
6) Check the checkbox to select channel.
7) Click Apply to save settings.
8) Click OK to back to the upper level menu.
Repeat the above steps to configure other alarm input parameters.
If the settings can also be applied to other alarm inputs, click Copy and choose the alarm input number.
Figure 5. 15 Copy Alarm Input
3. Edit the Alarm triggered record in the Record Schedule setting interface. For the detailed information of
schedule configuration, see Chapter 5.2 Configuring Recording Schedule.
User Manual of Network Video Recorder
77
5.5 Configuring VCA Event Recording
Purpose:
The event triggered recording can be configured through the menu. Then events include the motion detection,
alarm and VCA events (face detection/face capture, line crossing detection, intrusion detection, region entrance
detection, region exiting detection, loitering detection, people gathering detection, fast moving detection, parking
detection, unattended baggage detection, object removal detection, audio loss exception detection, sudden change
of sound intensity detection, and defocus detection).
Steps:
1. Enter the VCA settings interface and select a camera for the VCA settings.
Menu > Camera > VCA
Figure 5. 16 VCA Settings
2. Configure the detection rules for VCA events. For details, see the step 2 in Chapter 9 VCA Alarm.
3. Click the icon to configure the alarm linkage actions for the VCA events.
Select Trigger Channel tab and select one or more channels which will start to record when VCA alarm is
triggered.
Click Apply to save the settings
User Manual of Network Video Recorder
78
Figure 5. 17 Set Trigger Camera of VCA Alarm
The PTZ Linking function is only available for the VCA settings of IP cameras.
4. Enter Record Schedule settings interface (Menu > Record > Schedule > Record Schedule), and then set VCA
as the record type. For details, see step 2 in Chapter 5.2 Configuring Recording Schedule.
5.6 Manual Recording
Purpose:
Follow the steps to set parameters for the manual record. Using manual record, you need to manually cancel the
record. The manual recording is prior to the scheduled recording.
Steps:
1. Enter the Manual settings interface.
Menu > Manual
Or press the REC/SHOT button on the front panel.
Figure 5. 18 Manual Record
2. Enable the Manual Record.
1) Select Record on the left bar.
2) Click the status button before camera number to change to .
3. Disable manual record.
Click the status button to change to .
Green icon means that the channel is configured the record schedule. After rebooting, all the manual
records enabled will be canceled.
User Manual of Network Video Recorder
79
5.7 Configuring Holiday Recording
Purpose:
Follow the steps to configure the record schedule on holiday for that year. You may want to have different plan for
recording on holiday.
Steps:
1. Enter the Record setting interface.
Menu > Record > Holiday
Figure 5. 19 Holiday Settings
2. Enable Edit Holiday schedule.
1) Click to enter the Edit interface.
Figure 5. 20 Edit Holiday Settings
2) Check the checkbox after Enable Holiday.
3) Select Mode from the dropdown list.
There are three different modes for the date format to configure holiday schedule.
4) Set the start and end date.
5) Click Apply to save settings.
6) Click OK to exit the Edit interface.
3. Enter Record Schedule settings interface to edit the holiday recording schedule. See Chapter 5.2 Configuring
Recording Schedule.
User Manual of Network Video Recorder
80
5.8 Configuring Redundant Recording
Purpose:
Enabling redundant recording, which means saving the recording files not only in the R/W HDD but also in the
redundant HDD, will effectively enhance the data safety and reliability. .
Steps:
1. Enter HDD Information interface.
Menu > HDD
Figure 5. 21 HDD General
2. Select the HDD and click to enter the Local HDD Settings interface.
1) Set the HDD property to Redundancy.
Figure 5. 22 HDD General-Editing
2) Click Apply to save the settings.
3) Click OK to back to the upper level menu.
You must set the Storage mode in the HDD advanced settings to Group before you set the HDD property to
Redundant. For detailed information, please refer to Chapter 12.3.2 Setting HDD Property. There should
be at least another HDD which is in Read/Write status.
3. Enter the Record setting interface.
Menu > Record > Parameters
1) Select Record tab.
1) Click More Settings to enter the following interface.
User Manual of Network Video Recorder
81
Figure 5. 23 Record Parameters
2) Check the checkbox of Redundant Record.
3) Click OK to save settings and back to the upper level menu.
Repeat the above steps for configuring other channels.
User Manual of Network Video Recorder
82
5.9 Configuring HDD Group for Recording
Purpose:
You can group the HDDs and save the record files in certain HDD group.
Steps:
1. Enter HDD setting interface.
Menu > HDD
Figure 5. 24 HDD General
2. Select Advanced on the left side menu.
Figure 5. 25 Storage Mode
Check whether the storage mode of the HDD is Group. If not, set it to Group. For detailed information,
please refer to Chapter 12.3 Managing HDD Group.
3. Select General in the left side menu.
4. Click to enter editing interface.
5. Configuring HDD group.
1) Choose a group number for the HDD group.
2) Click Apply and then in the pop-up message box, click Yes to save your settings.
3) Click OK to back to the upper level menu.
Repeat the above steps to configure more HDD groups.
6. Choose the Channels which you want to save the record files in the HDD group.
1) Select Advanced on the left bar.
2) Choose Group number in the dropdown list of Record on HDD Group
3) Check the channels you want to save in this group.
4) Click Apply to save settings.
After having configured the HDD groups, you can configure the Recording settings following the
procedure provided in Chapter 5.2-5.7.
User Manual of Network Video Recorder
83
5.10 Files Protection
Purpose:
You can lock the recording files or set the HDD property to Read-only to protect the record files from being
overwritten.
5.10.1 Locking the Recording Files
Lock File when Playback
Steps:
1. Enter Playback interface.
Menu> Playback
2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar.
Figure 5. 26 Normal Playback
3. During playback, click the button to lock the current recording file.
In the multi-channel playback mde, clicking the button will lock all the record files related to the
playback channels.
4. You can click the button to pop up the file management interface. Click the Locked File tab to check
and export the locked files.
User Manual of Network Video Recorder
84
Figure 5. 27 Locked File Management
In the File Management interface, you can also click to change it to to unlock the file and the file
is not protected.
Lock File when Export
Steps:
1. Enter Export setting interface.
Menu > Export
Figure 5. 28 Export
2. Select the channels you want to investigate by checking the checkbox to .
3. Configure the record type, file type start/end time.
4. Click Search to show the results.
User Manual of Network Video Recorder
85
Figure 5. 29 Export- Search Result
5. Protect the record files.
1) Find the record files you want to protect, and then click the icon which will turn to , indicating
that the file is locked.
The record files of which the recording is still not completed cannot be locked.
2) Click to change it to to unlock the file and the file is not protected.
Figure 5. 30 Unlocking Attention
5.10.2 Setting HDD Property to Read-only
Steps:
1. Enter HDD setting interface.
Menu > HDD
Figure 5. 31 HDD General
2. Click to edit the HDD you want to protect.
User Manual of Network Video Recorder
86
Figure 5. 32 HDD General- Editing
To edit HDD property, you need to set the storage mode of the HDD to Group. See Chapter 12.3 Managing HDD
Group.
3. Set the HDD property to Read-only.
4. Click OK to save settings and back to the upper level menu.
You cannot save any files in a Read-only HDD. If you want to save files in the HDD, change the
property to R/W.
If there is only one HDD and is set to Read-only, the NVR can’t record any files. Only live view mode is
available.
If you set the HDD to Read-only when the NVR is saving files in it, then the file will be saved in next
R/W HDD. If there is only one HDD, the recording will be stopped.
User Manual of Network Video Recorder
87
Chapter 6 Playback
User Manual of Network Video Recorder
88
6.1 Playing Back Record Files
6.1.1 Instant Playback
Purpose:
Play back the recorded video files of a specific channel in the live view mode. Channel switch is supported.
Instant playback by channel
Step:
Choose a channel in live view mode and click the button in the quick setting toolbar.
In the instant playback mode, only record files recorded during the last five minutes on this channel will be played
back.
Figure 6. 1 Instant Playback Interface
6.1.2 Playing Back by Normal Search
Playback by Channel
1. Enter the Playback interface.
Mouse: right click a channel in live view mode and select Playback from the menu, as shown in Figure 6. 2.
User Manual of Network Video Recorder
89
Figure 6. 2 Right-click Menu under Live View
Pressing numerical buttons will switch playback to the corresponding channels during playback process.
Playback by Time
Purpose:
Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel switch
are supported.
Steps:
1. Enter playback interface.
Menu > Playback
2. Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar.
Figure 6. 3 Playback Calendar
If there are record files for that camera in that day, in the calendar, the icon for that day is displayed as .
User Manual of Network Video Recorder
90
Otherwise it is displayed as
Playback Interface
You can use the toolbar in the bottom part of Playback interface to control playing progress.
Figure 6. 4 Playback Interface
Click the channel(s) to execute simultaneous playback of multiple channels.
Figure 6. 5 Toolbar of Playback
The indicates the start/end time of the record.
Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to
locate specific frames.
Table 6. 1 Detailed Explanation of Playback Toolbar
Button
Operation
Button
Operation
Button
Operation
/
Audio on/ Mute
/
Start/Stop clipping
Lock File
Add default tag
Add customized tag
File management for
video clips, captured
pictures, locked files
and tags
/
Reverse play/ Pause
Stop
Digital Zoom
30s forward
30s reverse
/
Pause / Play
Fast forward
Previous day
Slow forward
Full Screen
Exit
Next day
User Manual of Network Video Recorder
91
Button
Operation
Button
Operation
Button
Operation
Save the clips
Process bar
/
Scaling up/down the
time line
6.1.3 Playing Back by Event Search
Purpose:
Play back record files on one or several channels searched out by event type (e.g., alarm input, motion detection
and VCA).
Steps:
1. Enter the Playback interface.
Menu > Playback
2. Select the Event in the drop-down list on the top-left side.
3. Select Alarm Input, Motion or VCA as the event type.
Here we take playback by VCA as the example.
Figure 6. 6 Motion Search Interface
4. Select the minor type of VCA from the drop-down list.
For configuring the VCA recording, please refer to Chapter 5.5 Configuring VCA Event Recording.
5. Select the camera (s) for searching, and set the Start time and End time.
6. Click Search button to get the search result information. You may refer to the right-side bar for the result.
7. Click button to play back the file.
Pre-play and post-play can be configured.
8. Playback interface.
User Manual of Network Video Recorder
92
The toolbar in the bottom part of Playback interface can be used to control playing process.
Figure 6. 7 Interface of Playback by Event
You can click or button to select the previous or next event. Please refer to Table 6. 1 for the description
of buttons on the toolbar.
6.1.4 Playing Back by Tag
Purpose:
Video tag allows you to record related information like people and location of a certain time point during playback.
You can use video tag(s) to search for record files and position time point.
Before playing back by tag:
1. Enter Playback interface.
Menu > Playback
2. Search and play back the record file(s). Refer to Chapter 6.1 for the detailed information about searching and
playback of the record files.
User Manual of Network Video Recorder
93
Figure 6. 8 Interface of Playback by Time
Click button to add default tag.
Click button to add customized tag and input tag name.
Max. 64 tags can be added to a single video file.
3. Tag management.
Click button to enter the File Management interface and click Tag to manage the tags. You can check,
edit and delete tag(s).
Figure 6. 9 Tag Management Interface
User Manual of Network Video Recorder
94
Playing back by Tag
Steps:
1. Select the Tag from the drop-down list in the Playback interface.
2. Choose channels, edit start time and end time, and then click Search to enter Search Result interface.
You can enter keyword in the textbox to search the tag on your command.
3. Click button to play back the selected tag file.
You can click the Back button to back to the search interface.
Figure 6. 10 Interface of Playback by Tag
Pre-play and post-play can be configured.
You can click or button to select the previous or next tag. Please refer to Table 6. 1 for the description of
buttons on the toolbar.
6.1.5 Playing back by Smart Playback
Purpose:
The smart playback function provides an easy way to get through the less effective information. When you select
the smart playback mode, the system will analyze the video containing the motion or VCA information, mark it
with green color and play it in the normal speed while the video without motion will be played in the 16-time
speed. The smart playback rules and areas are configurable.
Before you start:
To get the smart search result, the corresponding event type must be enabled and configured on the IP camera.
Here we take the intrusion detection as an example.
1. Log in the IP camera by the web browser, and enable the intrusion detection by checking the checkbox of it.
You may enter the motion detection configuration interface by Configuration > Advanced Configuration >
User Manual of Network Video Recorder
95
Events > Intrusion Detection.
Figure 6. 11 Setting Intrusion Detection on IP Camera
2. Configure the required parameters of intrusion detection, including area, arming schedule and linkage
methods. Refer to the user manual of smart IP camera for detailed instructions.
Steps:
1. Enter Playback interface.
Menu > Playback
2. Select the Smart in the drop-down list on the top-left side.
3. Select a camera in the camera list.
4. Select a date in the calendar and click the button on the left toolbar to play the video file.
Figure 6. 12 Smart Playback Interface
Table 6. 2 Detailed Explanation of Smart Playback Toolbar
Button
Operation
Button
Operation
Button
Operation
Draw line for the
line crossing
detection
Draw quadrilateral
for the intrusion
detection
Draw rectangle
for the intrusion
detection
Set full screen for
motion detection
Clear all
/
Start/Stop
clipping
File management for
video clips
Stop playing
/
Pause playing /
Play
Smart settings
Search matched
video files
Filter video files
by setting the
target characters
5. Set the rules and areas for smart search of VCA event or motion event.
User Manual of Network Video Recorder
96
Line Crossing Detection
Select the button , and click on the image to specify the start point and end point of the line.
Intrusion Detection
Click the button, and specify 4 points to set a quadrilateral region for intrusion detection. Only one
region can be set.
Motion Detection
Click the button and then click and draw the mouse to set the detection area manually. You can also
click the button to set the full screen as the detection area.
6. You can click to configure the smart settings.
Figure 6. 13 Smart Settings
Skip the Non-Related Video: The non-related video will not be played if this function is enabled.
Play Non-Related Video at: Set the speed to play the non-related video. Max./8/4/1 are selectable.
Play Related Video at: Set the speed to play the related video. Max./8/4/1 are selectable.
Pre-play and post-play is not available for the motion event type.
7. Click to search and play the matched video files.
8. (Optional) You can click to filter the searched video files by setting the target characters, including the
gender and age of the human and whether he/she wears glasses.
Figure 6. 14 Set Result Filter
User Manual of Network Video Recorder
97
6.1.6 Playing Back by System Logs
Purpose:
Play back record file(s) associated with channels after searching system logs.
Steps:
1. Enter Log Information interface.
Menu > Maintenance > Log Information
2. Click Log Search tab to enter Playback by System Logs.
Set search time and type and click Search button.
Figure 6. 15 System Log Search Interface
3. Choose a log with record file and click button to enter Playback interface.
Figure 6. 16 Result of System Log Search
4. Playback interface.
The toolbar in the bottom part of Playback interface can be used to control playing process.
User Manual of Network Video Recorder
98
Figure 6. 17 Interface of Playback by Log
6.1.7 Playing Back External File
Purpose:
Perform the following steps to look up and play back files in the external devices.
Steps:
1. Enter Tag Search interface.
Menu > Playback
2. Select the External File in the drop-down list on the top-left side.
The files are listed in the right-side list.
You can click the button to refresh the file list.
3. Select and click the button to play back it. And you can adjust the playback speed by clicking and
.
Figure 6. 18 Interface of External File Playback
User Manual of Network Video Recorder
99
6.1.8 Playing Back by Sub-periods
The DS-8600NI-E8, DS-7700/E4, DS-7600-E1(E2) series NVR supports playback by sub-periods.
Purpose:
The video files can be played in multiple sub-periods simultaneously on the screens.
Steps:
1. Enter Playback interface.
Menu > Playback
2. Select Sub-periods from the drop-down list in the upper-left corner of the page to enter the Sub-periods
Playback interface.
3. Select a date and start playing the video file.
4. Select the Split-screen Number from the dropdown list. Up to 16 screens are configurable.
Figure 6. 19 Interface of Sub-periods Playback
According to the defined number of split-screens, the video files on the selected date can be divided into average
segments for playback. E.g., if there are video files existing between 16:00 and 22:00, and the 6-screen display
mode is selected, then it can play the video files for 1 hour on each screen simultaneously.
User Manual of Network Video Recorder
100
Chapter 7 Backup
User Manual of Network Video Recorder
101
7.1 Backing up Record Files
7.1.1 Quick Export
Purpose:
Export record files to backup device(s) quickly.
Steps:
1. Enter Video Export interface.
Menu > Export > Normal
Choose the channel(s) you want to back up and click Quick Export button.
The time duration of record files on a specified channel cannot exceed one day. Otherwise, the message box
“Max. 24 hours are allowed for quick export.” will pop up.
Figure 7. 1 Quick Export Interface
2. Select the format of the log files to be exported. Up to 9 formats are selectable.
3. Click the Export to start exporting.
Here we use USB Flash Drive and please refer to the next section Normal Backup for more backup devices
supported by the NVR.
User Manual of Network Video Recorder
102
Figure 7. 2 Quick Export using USB1-1
Stay in the Exporting interface until all record files are exported.
Figure 7. 3 Export Finished
4. Check backup result.
The Player player.exe will be exported automatically during record file export.
Figure 7. 4 Checkup of Quick Export Result Using USB1-1
User Manual of Network Video Recorder
103
7.1.2 Backing up by Normal Video Search
Purpose:
The record files can be backup to various devices, such as USB devices (USB flash drives, USB HDDs, USB
writer), SATA writer and e-SATA HDD.
Backup using USB flash drives and USB HDDs
Steps:
1. Enter Export interface.
Menu>Export>Normal
2. Select the cameras to search.
3. Set search condition and click Search button to enter the search result interface. The matched video files are
displayed in Chart or List display mode.
Figure 7. 5 Normal Video Search for Backup
4. Select video files or pictures from the Chart or List to export.
Click to play the record file if you want to check it.
Check the checkbox before the record files you want to back up.
The size of the currently selected files is displayed in the lower-left corner of the window.
User Manual of Network Video Recorder
104
Figure 7. 6 Result of Normal Video Search for Backup
5. Export the video files or picture files.
Click Export All button to export all the files.
Or you can select recording files you want to back up, and click Export button to enter Export interface.
If the inserted USB device is not recognized:
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
You can also format USB flash drives or USB HDDs via the device.
Figure 7. 7 Export by Normal Video Search using USB Flash Drive
Stay in the Exporting interface until all record files are exported with pop-up message box “Export finished”.
User Manual of Network Video Recorder
105
Figure 7. 8 Export Finished
The backup of video files using USB writer or SATA writer has the same operating instructions. Please refer to
steps described above.
7.1.3 Backing up by Event Search
Purpose:
Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA writer
or eSATA HDD. Quick Backup and Normal Backup are supported.
Steps:
1. Enter Export interface.
Menu > Export > Event
2. Select the cameras to search.
3. Select the event type to alarm input, motion or VCA.
Figure 7. 9 Event Search for Backup
4. Set search condition and click Search button to enter the search result interface. The matched video files are
displayed in Chart or List display mode.
5. Select video files from the Chart or List interface to export.
User Manual of Network Video Recorder
106
Figure 7. 10 Result of Event Search
6. Export the video files. Please refer to step5 of Chapter 7.1.2 Backing up by Normal Video Search for details.
7.1.4 Backing up Video Clips
Purpose:
You may also select video clips in playback mode to export directly during Playback, using USB devices (USB
flash drives, USB HDDs, USB writer), SATA writer or eSATA HDD.
Steps:
1. Enter Playback interface.
Please refer to Chapter 6.1 Playing Back Record Files.
2. During playback, use buttons or in the playback toolbar to start or stop clipping record file(s).
3. Click the to enter the file management interface.
Figure 7. 11 Video Clips Export Interface
7. Export the video clips in playback. Please refer to step5 of Chapter 7.1.2 Backing up by Normal Video
Search for details.
User Manual of Network Video Recorder
107
7.2 Managing Backup Devices
Management of USB flash drives, USB HDDs and eSATA HDDs
Steps:
1. Enter the Export interface.
Figure 7. 12 Storage Device Management
2. Backup device management.
Click New Folder button if you want to create a new folder in the backup device.
Select a record file or folder in the backup device and click button if you want to delete it.
Click Erase button if you want to erase the files from a re-writable CD/DVD.
Click Format button to format the backup device.
If the inserted storage device is not recognized:
Click the Refresh button.
Reconnect device.
Check for compatibility from vendor.
User Manual of Network Video Recorder
108
Chapter 8 Alarm Settings
User Manual of Network Video Recorder
109
8.1 Setting Motion Detection Alarm
Steps:
1. Enter Motion Detection interface of Camera Management and choose a camera you want to set up motion
detection.
Menu > Camera > Motion
2. Set up detection area and sensitivity.
Tick Enable Motion Detection, and use the mouse to draw detection area(s) and drag the sensitivity bar to
set sensitivity.
By default, the motion detection is enabled and configured in full screen.
Click button and set alarm response actions.
Figure 8. 1 Motion Detection Setup Interface
3. Click Trigger Channel tab and select one or more channels which will start to record or become full-screen
monitoring when motion alarm is triggered, and click Apply to save the settings.
Figure 8. 2 Set Trigger Camera of Motion Detection
4. Set up arming schedule of the channel.
1) Select Arming Schedule tab to set the arming schedule of handling actions for the motion detection.
2) Choose one day of a week and up to eight time periods can be set within each day.
3) Click Apply to save the settings
User Manual of Network Video Recorder
110
Time periods shall not be repeated or overlapped.
Figure 8. 3 Set Arming Schedule of Motion Detection
5. Click Handling tab to set up alarm response actions of motion alarm (please refer to Chapter 8.6 Setting
Alarm Response Actions).
6. If you want to set motion detection for another channel, repeat the above steps or just click Copy in the
Motion Detection interface to copy the above settings to it.
User Manual of Network Video Recorder
111
8.2 Setting Sensor Alarms
Purpose:
Set the handling action of an external sensor alarm.
Steps:
1. Enter Alarm Settings of System Configuration and select an alarm input.
Menu> Configuration> Alarm
Select Alarm Input tab to enter Alarm Input Settings interface.
Figure 8. 4 Alarm Status Interface of System Configuration
2. Set up the handling action of the selected alarm input.
Check the Enable checkbox and click Settings button to set up its alarm response actions.
Figure 8. 5 Alarm Input Setup Interface
3. Select Trigger Channel tab and select one or more channels which will start to record or become full-screen
monitoring when an external alarm is input, and click Apply to save the settings.
4. Select Arming Schedule tab to set the arming schedule of handling actions.
User Manual of Network Video Recorder
112
Figure 8. 6 Set Arming Schedule of Alarm Input
Choose one day of a week and Max. eight time periods can be set within each day, and click Apply to save
the settings.
Time periods shall not be repeated or overlapped.
Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
5. Select Linkage Action tab to set up alarm response actions of the alarm input (please refer to Chapter 8.6
Setting Alarm Response Actions).
6. If necessary, select PTZ Linking tab and set PTZ linkage of the alarm input.
Set PTZ linking parameters and click OK to complete the settings of the alarm input.
Please check whether the PTZ or speed dome supports PTZ linkage.
One alarm input can trigger presets, patrol or pattern of more than one channel. But presets, patrols and
patterns are exclusive.
Figure 8. 7 Set PTZ Linking of Alarm Input
7. If you want to set handling action of another alarm input, repeat the above steps.
Or you can click the Copy button on the Alarm Input Setup interface and check the checkbox of alarm
User Manual of Network Video Recorder
113
inputs to copy the settings to them.
Figure 8. 8 Copy Settings of Alarm Input
User Manual of Network Video Recorder
114
8.3 Detecting Video Loss Alarm
Purpose:
Detect video loss of a channel and take alarm response action(s).
Steps:
1. Enter Video Loss interface of Camera Management and select a channel you want to detect.
Menu > Camera > Video Loss
Figure 8. 9 Video Loss Setup Interface
2. Set up handling action of video loss.
Check the checkbox of “Enable Video Loss Alarm”, and click button to set up handling action of video
loss.
3. Set up arming schedule of the handling actions.
1) Select Arming Schedule tab to set the channel’s arming schedule.
2) Choose one day of a week and up to eight time periods can be set within each day.
3) Click Apply button to save the settings.
Time periods shall not be repeated or overlapped.
Figure 8. 10 Set Arming Schedule of Video Loss
4. Select Linkage Action tab to set up alarm response action of video loss (please refer to Chapter 8.6 Setting
Alarm Response Actions).
5. Click the OK button to complete the video loss settings of the channel.
User Manual of Network Video Recorder
115
8.4 Detecting Video Tampering Alarm
Purpose:
Trigger alarm when the lens is covered and take alarm response action(s).
Steps:
1. Enter Video Tampering interface of Camera Management and select a channel you want to detect video
tampering.
Menu> Camera> Video Tampering
Figure 8. 11 Video Tampering Setup Interface
2. Set the video tampering handling action of the channel.
Check the checkbox of Enable Video Tampering Detection.
Drag the sensitivity bar to set a proper sensitivity level. Use the mouse to draw an area you want to detect
video tampering.
Click button to set up handling action of video tampering.
3. Set arming schedule and alarm response actions of the channel.
1) Click Arming Schedule tab to set the arming schedule of handling actions.
2) Choose one day of a week and max. eight time periods can be set within each day.
3) Click Apply button to save the settings.
Time periods shall not be repeated or overlapped.
User Manual of Network Video Recorder
116
Figure 8. 12 Set Arming Schedule of Video Tampering
4. Select Linkage Action tab to set up alarm response actions of video tampering alarm (please refer to
Chapter 8.6 Setting Alarm Response Actions).
5. Click the OK button to complete the video tampering settings of the channel.
User Manual of Network Video Recorder
117
8.5 Handling Exceptions Alarm
Purpose:
Exception settings refer to the handling action of various exceptions, e.g.
HDD Full: The HDD is full.
HDD Error: Writing HDD error or unformatted HDD.
Network Disconnected: Disconnected network cable.
IP Conflicted: Duplicated IP address.
Illegal Login: Incorrect user ID or password.
Record Exception: No space for saving recorded files.
PoE Power Overload: The power consumption of the connected cameras via the PoE interface exceeds the
maximum PoE power.
PoE Power Overload is only supported by DS-7600NI-E1/4P, DS-7600NI-E2/8P and DS-7700NI-E4/P series
NVR.
Steps:
Enter Exception interface of System Configuration and handle various exceptions.
Menu> Configuration> Exceptions
Please refer to Chapter 8.6 Setting Alarm Response Actions for detailed alarm response actions.
Figure 8. 13 Exceptions Setup Interface
User Manual of Network Video Recorder
118
8.6 Setting Alarm Response Actions
Purpose:
Alarm response actions will be activated when an alarm or exception occurs, including Event Hint Display, Full
Screen Monitoring, Audible Warning (buzzer), Notify Surveillance Center, Upload Picture to FTP, Trigger Alarm
Output and Send Email.
Event Hint Display
When an event or exception happens, a hint can be displayed on the lower-left corner of live view image. And you
can click the hint icon to check the details. Besides, the event to be displayed is configurable.
Steps:
1. Enter the Exception settings interface.
Menu > Configuration > Exceptions
2. Check the checkbox of Enable Event Hint.
Figure 8. 14 Event Hint Settings Interface
3. Click the to set the type of event to be displayed on the image.
Figure 8. 15 Event Hint Settings Interface
4. Click the OK button to finish settings.
Full Screen Monitoring
When an alarm is triggered, the local monitor (VGA and HDMI
TM
monitor) display in full screen the video image
from the alarming channel configured for full screen monitoring.
If alarms are triggered simultaneously in several channels, their full-screen images will be switched at an interval
of 10 seconds (default dwell time). A different dwell time can be set by going to Menu >Configuration>Live
View > Full Screen Monitoring Dwell Time.
Auto-switch will terminate once the alarm stops and you will be taken back to the Live View interface.
User Manual of Network Video Recorder
119
You must select during “Trigger Channel” settings the channel(s) you want to make full screen monitoring.
Audible Warning
Trigger an audible beep when an alarm is detected.
Notify Surveillance Center
Sends an exception or alarm signal to remote alarm host when an event occurs. The alarm host refers to the PC
installed with Remote Client.
The alarm signal will be transmitted automatically at detection mode when remote alarm host is configured. Please
refer to Chapter 11.2.6 Configuring Remote Alarm Host for details of alarm host configuration.
Email Linkage
Send an email with alarm information to a user or users when an alarm is detected.
Please refer to Chapter 11.2.10 for details of Email configuration.
Trigger Alarm Output
Trigger an alarm output when an alarm is triggered.
1. Enter Alarm Output interface.
Menu> Configuration> Alarm> Alarm Output
Select an alarm output and set alarm name and dwell time. Click Schedule button to set the arming schedule
of alarm output.
If “Manually Clear” is selected in the dropdown list of Dwell Time, you can clear it only by going to Menu>
Manual> Alarm.
Figure 8. 16 Alarm Output Setup Interface
2. Set up arming schedule of the alarm output.
Choose one day of a week and up to 8 time periods can be set within each day.
Time periods shall not be repeated or overlapped.
User Manual of Network Video Recorder
120
Figure 8. 17 Set Arming Schedule of Alarm Output
3. Repeat the above steps to set up arming schedule of other days of a week. You can also use Copy button to
copy an arming schedule to other days.
Click the OK button to complete the video tampering settings of the alarm output No.
4. You can also copy the above settings to another channel.
Figure 8. 18 Copy Settings of Alarm Output
User Manual of Network Video Recorder
121
8.7 Triggering or Clearing Alarm Output
Manually
Purpose:
Sensor alarm can be triggered or cleared manually. If “Manually Clear” is selected in the dropdown list of dwell
time of an alarm output, the alarm can be cleared only by clicking Clear button in the following interface.
Steps:
Select the alarm output you want to trigger or clear and make related operations.
Menu> Manual> Alarm
Click Trigger/Clear button if you want to trigger or clear an alarm output.
Click Trigger All button if you want to trigger all alarm outputs.
Click Clear All button if you want to clear all alarm output.
Figure 8. 19 Clear or Trigger Alarm Output Manually
User Manual of Network Video Recorder
122
Chapter 9 VCA Alarm
User Manual of Network Video Recorder
123
All VCA detection must be supported by the connected IP camera.
Face detection and vehicle detection are supported by DS-8600NI-E8 and DS-7700NI-E4 series.
9.1 Face Detection
Purpose:
Face detection function detects the face appears in the surveillance scene, and some certain actions can be taken
when the alarm is triggered.
Steps:
1. Enter the VCA settings interface.
Menu> Camera> VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
Figure 9. 1 Face Detection
3. Select the VCA detection type to Face Detection.
4. Click to enter the face detection settings interface. Configure the trigger channel, arming schedule and
linkage action for the face detection alarm. Please refer to step3~step5 of Chapter 8.1 Setting Motion
Detection Alarm for detailed instructions.
5. Click the Rule Settings button to set the face detection rules. You can click-and-drag the slider to set the
detection sensitivity.
Sensitivity: Range [1-5]. The higher the value is, the more easily the face can be detected.
Figure 9. 2 Set Face Detection Sensitivity
6. Click Apply to activate the settings.
User Manual of Network Video Recorder
124
9.2 Vehicle Detection
Purpose:
Vehicle Detection is available for the road traffic monitoring. In Vehicle Detection, the passed vehicle can be
detected and the picture of its license plate can be captured. You can send alarm signal to notify the surveillance
center and upload the captured picture to FTP server.
Steps:
1. Enter the VCA settings interface.
Menu > Camera > VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
3. Select the VCA detection type to Vehicle Detection.
4. Check the Enable checkbox to enable this function.
Figure 9. 3 Set Vehicle Detection
5. Click to configure the trigger channel, arming schedule and linkage actions for the Blacklist,
Whitelist and Others.
6. Click the Rule Settings to enter the rule settings interface. Configure the lane, upload picture and overlay
content settings. Up to 4 lanes are selectable.
User Manual of Network Video Recorder
125
Figure 9. 4 Rule Settings
7. Click Save to save the settings.
Please refer to the User Manual of Network Camera for the detailed instructions for the vehicle detection.
User Manual of Network Video Recorder
126
9.3 Line Crossing Detection
Purpose:
This function can be used for detecting people, vehicles and objects cross a set virtual line. The line crossing
direction can be set as bidirectional, from left to right or from right to left. And you can set the duration for the
alarm response actions, such as full screen monitoring, audible warning, etc.
Steps:
1. Enter the VCA settings interface.
Menu> Camera> VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
3. Select the VCA detection type to Line Crossing Detection.
4. Check the Enable checkbox to enable this function.
5. Click to configure the trigger channel, arming schedule and linkage actions for the line crossing
detection alarm.
6. Click the Rule Settings button to set the line crossing detection rules.
1) Select the direction to A<->B, A->B or A<-B.
A<->B: Only the arrow on the B side shows; when an object going across the configured line with both
direction can be detected and alarms are triggered.
A->B: Only the object crossing the configured line from the A side to the B side can be detected.
B->A: Only the object crossing the configured line from the B side to the A side can be detected.
2) Click-and-drag the slider to set the detection sensitivity.
Sensitivity: Range [1-100]. The higher the value is, the more easily the detection alarm can be triggered.
3) Click-OK to save the rule settings and back to the line crossing detection settings interface.
Figure 9. 5 Set Line Crossing Detection Rules
7. Click and set two points in the preview window to draw a virtual line.
You can use the to clear the existing virtual line and re-draw it.
User Manual of Network Video Recorder
127
Up to 4 rules can be configured.
Figure 9. 6 Draw Line for Line Crossing Detection
8. Click Apply to activate the settings.
User Manual of Network Video Recorder
128
9.4 Intrusion Detection
Purpose:
Intrusion detection function detects people, vehicle or other objects which enter and loiter in a pre-defined virtual
region, and some certain actions can be taken when the alarm is triggered.
Steps:
1. Enter the VCA settings interface.
Menu> Camera> VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
3. Select the VCA detection type to Intrusion Detection.
4. Check the Enable checkbox to enable this function.
5. Click to configure the trigger channel, arming schedule and linkage actions for the line crossing
detection alarm.
6. Click the Rule Settings button to set the intrusion detection rules. Set the following parameters.
1) Threshold: Range [1s-10s], the threshold for the time of the object loitering in the region. When the
duration of the object in the defined detection area is longer than the set time, the alarm will be
triggered.
2) Click-and-drag the slider to set the detection sensitivity.
Sensitivity: Range [1-100]. The value of the sensitivity defines the size of the object which can trigger
the alarm. The higher the value is, the more easily the detection alarm can be triggered.
3) Percentage: Range [1-100]. Percentage defines the ratio of the in-region part of the object which can
trigger the alarm. For example, if the percentage is set as 50%, when the object enters the region and
occupies half of the whole region, the alarm is triggered.
Figure 9. 7 Set Intrusion Crossing Detection Rules
4) Click-OK to save the rule settings and back to the line crossing detection settings interface.
7. Click and draw a quadrilateral in the preview window by specifying four vertexes of the detection
region, and right click to complete drawing. Only one region can be configured.
You can use the to clear the existing virtual line and re-draw it.
Up to 4 rules can be configured.
User Manual of Network Video Recorder
129
Figure 9. 8 Draw Area for Intrusion Detection
8. Click Apply to save the settings.
User Manual of Network Video Recorder
130
9.5 Region Entrance Detection
Purpose:
Region entrance detection function detects people, vehicle or other objects which enter a pre-defined virtual region
from the outside place, and some certain actions can be taken when the alarm is triggered.
Steps:
1. Enter the VCA settings interface.
Menu > Camera > VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
3. Select the VCA detection type to Region Entrance Detection.
4. Check the Enable checkbox to enable this function.
5. Click to configure the trigger channel, arming schedule and linkage actions for the line crossing
detection alarm.
6. Click the Rule Settings button to set the sensitivity of the region entrance detection.
Sensitivity: Range [0-100]. The higher the value is, the more easily the detection alarm can be triggered.
7. Click and draw a quadrilateral in the preview window by specifying four vertexes of the detection
region, and right click to complete drawing. Only one region can be configured.
You can use the to clear the existing virtual line and re-draw it.
Figure 9. 9 Set Region Entrance Detection
Up to 4 rules can be configured.
8. Click Apply to save the settings.
User Manual of Network Video Recorder
131
9.6 Region Exiting Detection
Purpose:
Region exiting detection function detects people, vehicle or other objects which exit from a pre-defined virtual
region, and some certain actions can be taken when the alarm is triggered.
Please refer to the Chapter 9.5 Region Entrance Detection for operating steps to configure the region exiting
detection.
Up to 4 rules can be configured.
9.7 Loitering Detection
Purpose:
Loitering detection function detects people, vehicle or other objects which loiter in a pre-defined virtual region for
some certain time, and a series of actions can be taken when the alarm is triggered.
Please refer to the Chapter 9.4 Intrusion Detection for operating steps to configure the loitering detection.
The Threshold [1s-10s] in the Rule Settings defines the time of the object loitering in the region. If you set
the value as 5, alarm is triggered after the object loitering in the region for 5s; and if you set the value as 0,
alarm is triggered immediately after the object entering the region.
Up to 4 rules can be configured.
9.8 People Gathering Detection
Purpose:
People gathering detection alarm is triggered when people gather around in a pre-defined virtual region, and a
series of actions can be taken when the alarm is triggered.
Please refer to the Chapter 9.4 Intrusion Detection for operating steps to configure the people gathering
detection.
The Percentage in the Rule Settings defines the gathering density of the people in the region. Usually, when
the percentage is small, the alarm can be triggered when small number of people gathered in the defined
detection region.
Up to 4 rules can be configured.
9.9 Fast Moving Detection
Purpose:
Fast moving detection alarm is triggered when people, vehicle or other objects move fast in a pre-defined virtual
region, and a series of actions can be taken when the alarm is triggered.
User Manual of Network Video Recorder
132
Please refer to the Chapter 9.4 Intrusion Detection for operating steps to configure the fast moving detection.
The Sensitivity in the Rule Settings defines the moving speed of the object which can trigger the alarm. The
higher the value is, the more easily a moving object can trigger the alarm.
Up to 4 rules can be configured.
9.10 Parking Detection
Purpose:
Parking detection function detects illegal parking in places such as highway, one-way street, etc., and a series of
actions can be taken when the alarm is triggered.
Please refer to the Chapter 9.4 Intrusion Detection for operating steps to configure the parking detection.
The Threshold[5s-20s] in the Rule Settings defines the time of the vehicle parking in the region. If you set
the value as 10, alarm is triggered after the vehicle stay in the region for 10s.
Up to 4 rules can be configured.
9.11 Unattended Baggage Detection
Purpose:
Unattended baggage detection function detects the objects left over in the pre-defined region such as the baggage,
purse, dangerous materials, etc., and a series of actions can be taken when the alarm is triggered.
Please refer to the Chapter 9.4 Intrusion Detection for operating steps to configure the unattended baggage
detection.
The Threshold[5s-20s] in the Rule Settings defines the time of the objects left over in the region. If you set
the value as 10, alarm is triggered after the object is left and stay in the region for 10s. And the Sensitivity
defines the similarity degree of the background image. Usually, when the sensitivity is high, a very small
object left in the region can trigger the alarm.
Up to 4 rules can be configured.
9.12 Object Removal Detection
Purpose:
Object removal detection function detects the objects removed from the pre-defined region, such as the exhibits on
display, and a series of actions can be taken when the alarm is triggered.
User Manual of Network Video Recorder
133
Please refer to the Chapter 9.4 Intrusion Detection for operating steps to configure the object removal
detection.
The Threshold [5s-20s] in the Rule Settings defines the time of the objects removed from the region. If you
set the value as 10, alarm is triggered after the object disappears from the region for 10s. And the Sensitivity
defines the similarity degree of the background image. Usually, when the sensitivity is high, a very small
object taken from the region can trigger the alarm.
Up to 4 rules can be configured.
9.13 Audio Exception Detection
Purpose:
Audio exception detection function detects the abnormal sounds in the surveillance scene, such as the sudden
increase / decrease of the sound intensity, and some certain actions can be taken when the alarm is triggered.
Steps:
1. Enter the VCA settings interface.
Menu> Camera> VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
3. Select the VCA detection type to Audio Exception Detection.
4. Click to configure the trigger channel, arming schedule and linkage action for the face detection alarm.
5. Click the Rule Settings button to set the audio exception rules.
Figure 9. 10 Set Audio Exception Detection Rules
1) Check the checkbox of Audio Input Exception to enable the audio loss detection function.
2) Check the checkbox of Sudden Increase of Sound Intensity Detection to detect the sound steep rise in
the surveillance scene. You can set the detection sensitivity and threshold for sound steep rise.
Sensitivity: Range [1-100], the smaller the value is, the more severe the change should be to trigger the
detection.
Sound Intensity Threshold: Range [1-100], it can filter the sound in the environment, the louder the
environment sound, the higher the value should be. You can adjust it according to the real environment.
3) Check the checkbox of Sudden Decrease of Sound Intensity Detection to detect the sound steep drop
in the surveillance scene. You can set the detection sensitivity[1-100] for sound steep drop.
User Manual of Network Video Recorder
134
6. Click Apply to activate the settings.
9.14 Sudden Scene Change Detection
Purpose:
Scene change detection function detects the change of surveillance environment affected by the external factors;
such as the intentional rotation of the camera, and some certain actions can be taken when the alarm is triggered.
Please refer to the Chapter 9.1 Face Detection for operating steps to configure the scene change detection.
The Sensitivity in the Rule Settings ranges from 1 to 100, and the higher the value is, the more easily the
change of scene can trigger the alarm.
9.15 Defocus Detection
Purpose:
The image blur caused by defocus of the lens can be detected, and some certain actions can be taken when the
alarm is triggered.
Please refer to the Chapter 9.1 Face Detection for operating steps to configure the defocus detection.
The Sensitivity in the Rule Settings ranges from 1 to 100, and the higher the value is, the more easily the
defocus image can trigger the alarm.
9.16 PIR Alarm
Purpose:
A PIR (Passive Infrared) alarm is triggered when an intruder moves within the detector's field of view. The heat
energy dissipated by a person, or any other warm blooded creature such as dogs, cats, etc., can be detected.
Steps:
1. Enter the VCA settings interface.
Menu> Camera> VCA
2. Select the camera to configure the VCA.
You can click the checkbox of Save VCA Picture to save the captured pictures of VCA detection.
3. Select the VCA detection type to PIR Alarm.
4. Click to configure the trigger channel, arming schedule and linkage action for the PIR alarm.
5. Click the Rule Settings button to set the rules. Please refer to the Chapter 9.1 Face Detection for
instructions.
6. Click Apply to activate the settings.
User Manual of Network Video Recorder
135
Chapter 10 VCA Search
User Manual of Network Video Recorder
136
With the configured VCA detection, the NVR supports the VCA search for the behavior analysis, face capture,
people counting and heat map results.
The DS-7600 series NVR supports the behavior search only.
10.1 Face Search
Purpose:
When there are detected face picture captured and saved in HDD, you can enter the Face Search interface to search
the picture and play the picture related video file according to the specified conditions.
Before you start:
Please refer to Section 9.1 Face Detection for configuring the face detection.
Steps:
1. Enter the Face Search interface.
Menu>VCA Search> Face Search
2. Select the camera (s) for the face search.
Figure 10. 1 Face Search
3. Specify the start time and end time for search the captured face pictures or video files.
4. Click Search to start searching. The search results of face detection pictures are displayed in list or in chart.
User Manual of Network Video Recorder
137
Figure 10. 2 Face Search Interface
5. Play the face picture related video file.
You can double click on a face picture to play its related video file in the view window on the top right, or
select a picture item and click to play it.
You can also click to stop the playing, or click / to play the previous/next file.
6. If you want to export the captured face pictures to local storage device, connect the storage device to the
device and click Export All to enter the Export interface.
Click Export to export all face pictures to the storage device.
Please refer to Chapter 7 Backup for the operation of exporting files.
Figure 10. 3 Export Files
User Manual of Network Video Recorder
138
10.2 Behavior Search
Purpose:
The behavior analysis detects a series of suspicious behavior based on VCA detection, and certain linkage methods
will be enabled if the alarm is triggered.
Steps:
1. Enter the Behavior Search interface.
Menu>VCA Search> Behavior Search
2. Select the camera (s) for the behavior search.
3. Specify the start time and end time for searching the matched pictures.
Figure 10. 4 Behavior Search Interface
4. Select the VCA detection type from the dropdown list, including the line crossing detection, intrusion
detection, unattended baggage detection, object removal detection, region entrance detection, region exiting
detection, parking detection, loitering detection, people gathering detection and fast moving detection.
5. Click Search to start searching. The search results of pictures are displayed in list or in chart.
User Manual of Network Video Recorder
139
Figure 10. 5 Behavior Search Results
6. Play the behavior analysis picture related video file.
You can double click on a picture from the list to play its related video file in the view window on the top
right, or select a picture item and click to play it.
You can also click to stop the playing, or click / to play the previous/next file.
7. If you want to export the captured pictures to local storage device, connect the storage device to the device
and click Export All to enter the Export interface.
Click Export to export all pictures to the storage device.
10.3 Plate Search
Purpose: You can search and view the matched captured vehicle plate picture and related information according to
the plate searching conditions including the start time/end time, country and plate No..
Steps:
1. Enter the Plate Search interface.
Menu > VCA Search > Plate Search
2. Select the camera (s) for the plate search.
3. Specify the start time and end time for searching the matched plate pictures.
User Manual of Network Video Recorder
140
Figure 10. 6 Plate Search
4. Select the country from the drop-down list for searching the location of the vehicle plate.
5. Input the plate No. in the field for search.
7. Click Search to start searching. The search results of detected vehicle plate pictures are displayed in list or in
chart.
Please refer to the Step7-Step8 of Section 10.1 Face Search for the operation of the search results.
10.4 People Counting
Purpose:
The People Counting is used to calculate the number of people entered or left a certain configured area and form in
daily/weekly/monthly/annual reports for analysis.
Steps:
1. Enter the People Counting interface.
Menu>VCA Search> People Counting
2. Select the camera for the people counting.
3. Select the report type to Daily Report, Weekly Report, Monthly Report or Annual Report.
4. Set the statistics time.
5. Click the Counting button to start people counting statistics.
User Manual of Network Video Recorder
141
Figure 10. 7 People Counting Interface
6. You can click the Export button to export the statistics report in excel format.
User Manual of Network Video Recorder
142
10.5 Heat Map
Purpose:
Heat map is a graphical representation of data represented by colors. The heat map function is usually used to
analyze the visit times and dwell time of customers in a configured area.
The heat map function must be supported by the connected IP camera and the corresponding configuration must be
set.
Steps:
1. Enter the Heat Map interface.
Menu>VCA Search> Heat Map
2. Select the camera for the heat map processing.
3. Select the report type to Daily Report, Weekly Report, Monthly Report or Annual Report.
4. Set the statistics time.
Figure 10. 8 Heat Map Interface
5. Click the Counting button to export the report data and start heat map statistics, and the results are displayed
in graphics marked in different colors.
As shown in the figure above, red color block (255, 0, 0) indicates the most welcome area, and blue color
block (0, 0, 255) indicates the less-popular area.
You can click the Export button to export the statistics report in excel format.
User Manual of Network Video Recorder
143
Chapter 11 Network Settings
User Manual of Network Video Recorder
144
11.1 Configuring General Settings
Purpose:
Network settings must be properly configured before you operate NVR over network.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the General tab.
Figure 11. 1 Network Settings Interface of DS-8600NI-E8 and DS-7700NI-E4
The dual-NIC network 10 /100/1000 Mbps self-adaptive Ethernet interfaces are provided for the
DS-8600NI-E8 and DS-7700NI-E4 series NVR; one 10 /100 Mbps self-adaptive Ethernet interface for
DS-7604/7608NI-E1(E2) series NVR; and one 10 /100/1000 Mbps self-adaptive Ethernet interface for
other models.
3. In the General Settings interface, you can configure the following settings: Working Mode, NIC Type, IPv4
Address, IPv4 Gateway, MTU and DNS Server.
If the DHCP server is available, you can click the checkbox of DHCP to automatically obtain an IP address
and other network settings from that server.
For the models which have the PoE or built-in switch network interfaces, including
DS-7600NI-E1(E2)/N, DS-7600NI-E1(E2)/P and DS-7700NI-E4/P series NVR, the internal NIC IPv4
address should be configured for the cameras connecting to the PoE or built-in switch network
interface of the NVR.
The valid value range of MTU is 500 ~ 9676.
4. After having configured the general settings, click Apply button to save the settings.
Working Mode
Two 10M/100M/1000M NIC cards are provided by the DS-8600NI-E8 and DS-7700NI-E4 series device, which
allows the device to work in the Multi-address and Net-fault Tolerance modes.
Multi-address Mode: The parameters of the two NIC cards can be configured independently. You can select
LAN1 or LAN2 in the NIC type field for parameter settings.
User Manual of Network Video Recorder
145
You can select one NIC card as default route. And then the system is connecting with the extranet the data will be
forwarded through the default route.
Net-fault Tolerance Mode: The two NIC cards use the same IP address, and you can select the Main NIC to
LAN1 or LAN2. By this way, in case of one NIC card failure, the device will automatically enable the other
standby NIC card so as to ensure the normal running of the whole system.
Figure 11. 2 Net Fault-tolerance Working Mode
User Manual of Network Video Recorder
146
11.2 Configuring Advanced Settings
11.2.1 PPPoE Settings
Purpose:
Your NVR also allows access by Point-to-Point Protocol over Ethernet (PPPoE).
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the PPPoE tab to enter the PPPoE Settings interface, as shown in Figure 11. 3.
Figure 11. 3 PPPoE Settings Interface
3. Check the PPPoE checkbox to enable this feature.
4. Enter User Name and Password for PPPoE access.
The User Name and Password should be assigned by your ISP.
5. Click the Apply button to save and exit the interface.
6. After successful settings, the system asks you to reboot the device to enable the new settings, and the PPPoE
dial-up is automatically connected after reboot.
You can go to Menu >Maintenance>System Info >Network interface to view the status of PPPoE connection.
Please refer to Chapter 14.1 Viewing System Information for PPPoE status.
11.2.2 Configuring EZVIZ Cloud P2P
Purpose:
EZVIZ Cloud P2P provides the mobile phone application and as well the service platform page to access and
manage your connected NVR, which enables you to get a convenient remote access to the surveillance system.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the Platform Access tab to enter the EZVIZ Cloud P2P Settings interface.
3. Check the Enable checkbox to activate this feature.
4. If required, select the checkbox of Custom and input the Server Address.
5. To turn the Enable Stream Encryption on, you can select its checkbox.
6. Enter the Verification Code of the device.
The verification code consists of 6 capital letters and is located at the bottom of the DVR. You can also use the
User Manual of Network Video Recorder
147
scanning tool of your phone to quickly get the code by scanning the QR code below.
Figure 11. 4 EZVIZ Cloud P2P Settings Interface
7. Click the Apply button to save and exit the interface.
After configuration, you can access and manage the NVR by your mobile phone on which the EZVIZ Cloud P2P
application is installed or by the EZVIZ website (www.ezviz7.com).
For more operation instructions, please refer to the help file on the EZVIZ official website (www.ezviz7.com).
11.2.3 Configuring DDNS
Purpose:
If your NVR is set to use PPPoE as its default network connection, you may set Dynamic DNS (DDNS) to be used
for network access.
Prior registration with your ISP is required before configuring the system to use DDNS.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the DDNS tab to enter the DDNS Settings interface.
3. Check the Enable DDNS checkbox to enable this feature.
4. Select DDNS Type. Five different DDNS types are selectable: IPServer, DynDNS, PeanutHull, NO-IP and
HiDDNS.
IPServer: Enter Server Address for IPServer.
User Manual of Network Video Recorder
148
Figure 11. 5 IPServer Settings Interface
DynDNS:
1) Enter Server Address for DynDNS (i.e. members.dyndns.org).
2) In the NVR Domain Name text field, enter the domain obtained from the DynDNS website.
3) Enter the User Name and Password registered in the DynDNS website.
Figure 11. 6 DynDNS Settings Interface
PeanutHull: Enter the User Name and Password obtained from the PeanutHull website.
Figure 11. 7 PeanutHull Settings Interface
NO-IP:
Enter the account information in the corresponding fields. Refer to the DynDNS settings.
1) Enter Server Address for NO-IP.
User Manual of Network Video Recorder
149
2) In the NVR Domain Name text field, enter the domain obtained from the NO-IP website
(www.no-ip.com).
3) Enter the User Name and Password registered in the NO-IP website.
Figure 11. 8 NO-IP Settings Interface
HiDDNS:
1) Select the continent/country of the server on which the device is registered.
2) The Server Address of the HiDDNS server appears by default: www.hik-online.com.
3) Enter the Device Domain Name. You can use the alias you registered in the HiDDNS server or
define a new device domain name. If a new alias of the device domain name is defined in the NVR,
it will replace the old one registered on the server. You can register the alias of the device domain
name in the HiDDNS server first and then enter the alias to the Device Domain Name in the NVR;
you can also enter the domain name directly on the NVR to create a new one.
Figure 11. 9 HiDDNS Settings Interface
Register the device on the HiDDNS server.
1) Go to the HiDDNS website: www.hik-online.com.
User Manual of Network Video Recorder
150
Figure 11. 10 Register an Account
2) Click to register an account if you do not have one and use the account to log in.
Figure 11. 11 Register an Account
3) In the Device Management interface, click to register the device.
User Manual of Network Video Recorder
151
Figure 11. 12 Register the Device
4) Input Device Serial No., Device Domain (Device Name) and HTTP Port. And click OK to
add the device.
Access the Device via Web Browser or Client Software
After having successfully registered the device on the HiDDNS server, you can access your device
via web browser or Client Software with the Device Domain Name (Device Name).
OPTION 1: Access the Device via Web Browser
Open a web browser, and enter http://www.hik-online.com/alias in the address bar. Alias refers to
the Device Domain Name on the device or the Device Name on the HiDDNS server.
Example: http://www.hik-online.com/nvr
If you mapped the HTTP port on your router and changed it to port No. except 80, you have to
enter http://www.hik-online.com/alias:HTTP port in the address bar to access the device. You can
refer to Chapter 9.2.11 for the mapped HTTP port No.
OPTION 2: Access the devices via iVMS-4200
For iVMS-4200, in the Add Device window, select and then edit the device
information.
Nickname: Edit a name for the device as you want.
Server Address: www.hik-online.com
Device Domain Name: It refers to the Device Domain Name on the device or the Device Name
on the HiDDNS server you created.
User Name: Enter the user name of the device.
Password: Enter the password of the device.
User Manual of Network Video Recorder
152
Figure 11. 13 Access Device via iVMS-4200
5. Click the Apply button to save the settings.
After setting all the required parameters for the DDNS, you can view the connecting status of the device by
checking the Status information.
11.2.4 Configuring NTP Server
Purpose:
Ensure the network connection of the PC (running FTP server) and the device is valid and correct. Run the FTP
server on the PC and copy the firmware into the corresponding directory of your PC.
Refer to the user manual of the FTP server to set the FTP server on your PC and put the firmware file into the
directory as required.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the NTP tab to enter the NTP Settings interface, as shown in Figure 11. 14.
Figure 11. 14 NTP Settings Interface
3. Check the Enable NTP checkbox to enable this feature.
4. Configure the following NTP settings:
Interval: Time interval between the two synchronizing actions with NTP server. The unit is minute.
NTP Server: IP address of NTP server.
NTP Port: Port of NTP server.
5. Click the Apply button to save and exit the interface.
User Manual of Network Video Recorder
153
The time synchronization interval can be set from1 to 10080min, and the default value is 60min. If the NVR is
connected to a public network, you should use a NTP server that has a time synchronization function, such as the
server at the National Time Center (IP Address: 210.72.145.44). If the NVR is setup in a more customized network,
NTP software can be used to establish a NTP server used for time synchronization.
11.2.5 Configuring SNMP
Purpose:
You can use SNMP protocol to get device status and parameters related information.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the SNMP tab to enter the SNMP Settings interface, as shown in Figure 11. 15.
Figure 11. 15 SNMP Settings Interface
3. Check the SNMP checkbox to enable this feature.
4. Configure the following SNMP settings:
Trap Address: IP Address of SNMP host.
Trap Port: Port of SNMP host.
5. Click the Apply button to save and exit the interface.
Before setting the SNMP, please download the SNMP software and manage to receive the device information via
SNMP port. By setting the Trap Address, the NVR is allowed to send the alarm event and exception message to
the surveillance center.
11.2.6 Configuring Remote Alarm Host
Purpose:
With a remote alarm host configured, the NVR will send the alarm event or exception message to the host when an
alarm is triggered. The remote alarm host must have the Network Video Surveillance software installed.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 11. 16.
User Manual of Network Video Recorder
154
Figure 11. 16 More Settings Interface
3. Enter Alarm Host IP and Alarm Host Port in the text fields.
The Alarm Host IP refers to the IP address of the remote PC on which the Network Video Surveillance
Software (e.g., iVMS-4200) is installed, and the Alarm Host Port must be the same as the alarm monitoring
port configured in the software.
4. Click the Apply button to save and exit the interface.
11.2.7 Configuring Multicast
Purpose:
The multicast can be configured to realize live view for more than 128 connections through network for the device.
A multicast address spans the Class-D IP range of 224.0.0.0 to239.255.255.255. It is recommended to use the IP
address ranging from 239.252.0.0 to 239.255.255.255.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 11. 16.
3. Set Multicast IP, as shown in Figure 11. 17. When adding a device to the Network Video Surveillance
Software, the multicast address must be the same as the NVR’s multicast IP.
Figure 11. 17 Configure Multicast
4. Click the Apply button to save and exit the interface.
The multicast function should be supported by the network switch to which the NVR is connected.
11.2.8 Configuring RTSP
Purpose:
The RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in communication
systems to control streaming media servers.
Steps:
User Manual of Network Video Recorder
155
1. Enter the Network Settings menu
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings menu, as shown in Figure 11. 16.
Figure 11. 18 RTSP Settings Interface
3. Enter the RTSP port in the text field of RTSP Service Port. The default RTSP port is 554, and you can
change it according to different requirements.
4. Click the Apply button to save and exit the menu.
11.2.9 Configuring Server and HTTP Ports
Purpose:
You can change the server and HTTP ports in the Network Settings menu. The default server port is 8000 and the
default HTTP port is 80.
Steps:
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Select the More Settings tab to enter the More Settings interface, as shown in Figure 11. 16.
3. Enter new Server Port and HTTP Port.
Figure 11. 19 Host/Others Settings Menu
4. Enter the Server Port and HTTP Port in the text fields. The default Server Port is 8000 and the HTTP Port is
80, and you can change them according to different requirements.
5. Click the Apply button to save and exit the interface.
The Server Port should be set to the range of 2000-65535 and it is used for remote client software access. The
HTTP port is used for remote web browser access.
11.2.10 Configuring Email
Purpose:
The system can be configured to send an Email notification to all designated users if an alarm event is detected,
etc., an alarm or motion event is detected or the administrator password is changed.
Before configuring the Email settings, the NVR must be connected to a local area network (LAN) that maintains
an SMTP mail server. The network must also be connected to either an intranet or the Internet depending on the
location of the e-mail accounts to which you want to send notification.
Steps:
User Manual of Network Video Recorder
156
1. Enter the Network Settings interface.
Menu >Configuration> Network
2. Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS Server in the Network
Settings men.
Figure 11. 20 Network Settings Interface
3. Click Apply to save the settings.
4. Select the Email tab to enter the Email Settings interface.
Figure 11. 21 Email Settings Interface
5. Configure the following Email settings:
Enable Server Authentication (optional): Check the checkbox to enable the server authentication feature.
User Name: The user account of sender’s Email for SMTP server authentication.
Password: The password of sender’s Email for SMTP server authentication.
SMTP Server: The SMTP Server IP address or host name (e.g., smtp.263xmail.com).
SMTP Port No.: The SMTP port. The default TCP/IP port used for SMTP is 25.
Enable SSL (optional): Click the checkbox to enable SSL if required by the SMTP server.
Sender: The name of sender.
Sender’s Address: The Email address of sender.
Select Receivers: Select the receiver. Up to 3 receivers can be configured.
Receiver: The name of user to be notified.
Receiver’s Address: The Email address of user to be notified.
Enable Attached Pictures: Check the checkbox of Enable Attached Picture if you want to send email
with attached alarm images. The interval is the time of two adjacent alarm images. You can also set SMTP
port and enable SSL here.
Interval: The interval refers to the time between two actions of sending attached pictures.
User Manual of Network Video Recorder
157
E-mail Test: Sends a test message to verify that the SMTP server can be reached.
6. Click Apply button to save the Email settings.
7. You can click Test button to test whether your Email settings work. The corresponding Attention message
box will pop up. Refer to Figure 11. 22.
Figure 11. 22 Email Testing Attention
11.2.11 Configuring NAT
Purpose:
Two ways are provided for port mapping to realize the remote access via the cross-segment network, UPnP and
manual mapping.
UPnP
TM
Universal Plug and Play (UPnP™) can permit the device seamlessly discover the presence of other network
devices on the network and establish functional network services for data sharing, communications, etc. You can
use the UPnP™ function to enable the fast connection of the device to the WAN via a router without port mapping.
Before you start:
If you want to enable the UPnP™ function of the device, you must enable the UPnP™ function of the router to
which your device is connected. When the network working mode of the device is set as multi-address, the Default
Route of the device should be in the same network segment as that of the LAN IP address of the router.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the NAT tab to enter the port mapping interface.
Figure 11. 23 UPnP™ Settings Interface
3. Check checkbox to enable UPnP™.
4. Select the Mapping Type as Manual or Auto in the drop-down list.
OPTION 1: Auto
If you select Auto, the Port Mapping items are read-only, and the external ports are set by the router
automatically.
Steps:
1) Select Auto in the drop-down list of Mapping Type.
User Manual of Network Video Recorder
158
2) Click Apply button to save the settings.
3) You can click Refresh button to get the latest status of the port mapping.
Figure 11. 24 UPnP™ Settings Finished-Auto
OPTION 2: Manual
If you select Manual as the mapping type, you can edit the external port on your demand by clicking to
activate the External Port Settings dialog box.
Steps:
1) Select Manual in the drop-down list of Mapping Type.
2) Click to activate the External Port Settings dialog box. Configure the external port No. for server
port, http port, RTSP port and https port respectively.
You can use the default port No., or change it according to actual requirements.
External Port indicates the port No. for port mapping in the router.
The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the
other ports should be between 1 and 65535 and the value must be different from each other. If
multiple devices are configured for the UPnP™ settings under the same router, the value of the
port No. for each device should be unique.
Figure 11. 25 External Port Settings Dialog Box
3) Click Apply button to save the settings.
4) You can click Refresh button to get the latest status of the port mapping.
User Manual of Network Video Recorder
159
Figure 11. 26 UPnP™ Settings Finished-Manual
Manual Mapping
If your router does not support the UPnP
TM
function, perform the following steps to map the port manually in an
easy way.
Before you start:
Make sure the router support the configuration of internal port and external port in the interface of Forwarding.
Steps:
1. Enter the Network Settings interface.
Menu > Configuration > Network
2. Select the NAT tab to enter the port mapping interface.
3. Leave the Enable UPnP checkbox unchecked.
4. Click to activate the External Port Settings dialog box. Configure the external port No. for server port,
http port, RTSP port and https port respectively.
The value of the RTSP port No. should be 554 or between 1024 and 65535, while the value of the other ports
should be between 1 and 65535 and the value must be different from each other. If multiple devices are configured
for the UPnP™ settings under the same router, the value of the port No. for each device should be unique.
Figure 11. 27 External Port Settings Dialog Box
5. Click OK to save the setting for the current port and return to the upper-level menu.
6. Click Apply button to save the settings.
7. Enter the virtual server setting page of router; fill in the blank of Internal Source Port with the internal port
value, the blank of External Source Port with the external port value, and other required contents.
Each item should be corresponding with the device port, including server port, http port, RTSP port and https port.
User Manual of Network Video Recorder
160
Figure 11. 28 Setting Virtual Server Item
The above virtual server setting interface is for reference only, it may be different due to different router
manufactures. Please contact the manufacture of router if you have any problems with setting virtual server.
11.3 Checking Network Traffic
Purpose:
You can check the network traffic to obtain real-time information of NVR such as linking status, MTU,
sending/receiving rate, etc.
Steps:
1. Enter the Network Traffic interface.
Menu > Maintenance > Net Detect
Figure 11. 29 Network Traffic Interface
2. You can view the sending rate and receiving rate information on the interface. The traffic data is refreshed
every 1 second.
User Manual of Network Video Recorder
161
11.4 Configuring Network Detection
Purpose:
You can obtain network connecting status of NVR through the network detection function, including network
delay, packet loss, etc.
11.4.1 Testing Network Delay and Packet Loss
Steps:
1. Enter the Network Traffic interface.
Menu >Maintenance>Net Detect
2. Click the Network Detection tab to enter the Network Detection menu, as shown in Figure 11. 30.
Figure 11. 30 Network Detection Interface
3. Enter the destination address in the text field of Destination Address.
4. Click Test button to start testing network delay and packet loss. The testing result pops up on the window. If
the testing is failed, the error message box will pop up as well. Refer to Figure 11. 31.
Figure 11. 31 Testing Result of Network Delay and Packet Loss
11.4.2 Exporting Network Packet
Purpose:
By connecting the NVR to network, the captured network data packet can be exported to USB-flash disk, SATA,
DVD-R/W and other local backup devices.
Steps:
1. Enter the Network Traffic interface.
Menu >Maintenance>Net Detect
2. Click the Network Detection tab to enter the Network Detection interface.
3. Select the backup device from the dropdown list of Device Name, as shown in Figure 11. 32.
User Manual of Network Video Recorder
162
Click Refresh button if the connected local backup device cannot be displayed. When it fails to detect the backup
device, please check whether it is compatible with the NVR. You can format the backup device if the format is
incorrect.
Figure 11. 32 Export Network Packet
4. Click Export button to start exporting.
5. After the exporting is complete, click OK to finish the packet export, as shown in Figure 11. 33.
Figure 11. 33 Packet Export Attention
Up to 1M data can be exported each time.
11.4.3 Checking the Network Status
Purpose:
You can also check the network status and quick set the network parameters in this interface.
Step:
Click the Status button on the lower- right corner of the page.
User Manual of Network Video Recorder
163
Figure 11. 34 Network Status Checking
If the network is normal the following message box pops out.
Figure 11. 35 Network status checking result
If the message box pops out with other information instead of this one, you can click Network button to
show the quick setting interface of the network parameters.
11.4.4 Checking Network Statistics
Purpose:
You can check the network status to obtain the real-time information of NVR.
Steps:
1. Enter the Network Detection interface.
Menu>Maintenance>Net Detect
2. Choose the Network Stat. tab.
User Manual of Network Video Recorder
164
Figure 11. 36 Network Stat. Interface
3. Check the bandwidth of IP Camera, bandwidth of Remote Live View, bandwidth of Remote Playback,
bandwidth of Net Receive Idle and bandwidth of Net Send Idle.
4. You can click Refresh to get the newest status.
User Manual of Network Video Recorder
165
Chapter 12 HDD Management
User Manual of Network Video Recorder
166
12.1 Initializing HDDs
Purpose:
A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR.
A message box pops up when the NVR starts up if there exits any uninitialized HDD.
Figure 12. 1 Message Box of Uninitialized HDD
Click Yes button to initialize it immediately or you can perform the following steps to initialize the HDD.
Steps:
1. Enter the HDD Information interface.
Menu > HDD> General
Figure 12. 2 HDD Information Interface
2. Select HDD to be initialized.
3. Click the Init button.
Figure 12. 3 Confirm Initialization
4. Select the OK button to start initialization.
Figure 12. 4 Status changes to Initializing
5. After the HDD has been initialized, the status of the HDD will change from Uninitialized to Normal.
User Manual of Network Video Recorder
167
Figure 12. 5 HDD Status Changes to Normal
Initializing the HDD will erase all data on it.
User Manual of Network Video Recorder
168
12.2 Managing Network HDD
Purpose:
You can add the allocated NAS or disk of IP SAN to NVR, and use it as network HDD.
Steps:
1. Enter the HDD Information interface.
Menu > HDD>General
Figure 12. 6 HDD Information Interface
2. Click the Add button to enter the Add NetHDD interface, as shown in Figure 12. 7.
Figure 12. 7 HDD Information Interface
3. Add the allocated NetHDD.
4. Select the type to NAS or IP SAN.
5. Configure the NAS or IP SAN settings.
Add NAS disk:
1) Enter the NetHDD IP address in the text field.
2) Click the Search button to search the available NAS disks.
3) Select the NAS disk from the list shown below.
Or you can just manually enter the directory in the text field of NetHDD Directory.
4) Click the OK button to add the configured NAS disk.
Up to 8 NAS disks can be added.
User Manual of Network Video Recorder
169
Figure 12. 8 Add NAS Disk
Add IP SAN:
1) Enter the NetHDD IP address in the text field.
2) Click the Search button to search the available IP SAN disks.
3) Select the IP SAN disk from the list shown below.
4) Click the OK button to add the selected IP SAN disk.
Up to 1 IP SAN disk can be added.
Figure 12. 9 Add IP SAN Disk
6. After having successfully added the NAS or IP SAN disk, return to the HDD Information menu. The added
NetHDD will be displayed in the list.
If the added NetHDD is uninitialized, please select it and click the Init button for initialization.
User Manual of Network Video Recorder
170
Figure 12. 10 Initialize Added NetHDD
User Manual of Network Video Recorder
171
12.3 Managing HDD Group
12.3.1 Setting HDD Groups
Purpose:
Multiple HDDs can be managed in groups. Video from specified channels can be recorded onto a particular HDD
group through HDD settings.
Steps:
1. Enter the Storage Mode interface.
Menu > HDD > Advanced
2. Set the Mode to Group, as shown in Figure 12. 11.
Figure 12. 11 Storage Mode Interface
3. Click the Apply button and the following Attention box will pop up.
Figure 12. 12 Attention for Reboot
4. Click the Yes button to reboot the device to activate the changes.
5. After reboot of device, enter the HDD Information interface.
Menu > HDD> General
6. Select HDD from the list and click icon to enter the Local HDD Settings interface, as shown in Figure
12. 13.
User Manual of Network Video Recorder
172
Figure 12. 13 Local HDD Settings Interface
7. Select the Group number for the current HDD.
The default group No. for each HDD is 1.
8. Click the OK button to confirm the settings.
Figure 12. 14 Confirm HDD Group Settings
9. In the pop-up Attention box, click the Yes button to finish the settings.
12.3.2 Setting HDD Property
Purpose:
The HDD property can be set to redundancy, read-only or read/write (R/W). Before setting the HDD property,
please set the storage mode to Group (refer to step1-4 of Chapter 12.3.1 Setting HDD Groups ).
A HDD can be set to read-only to prevent important recorded files from being overwritten when the HDD becomes
full in overwrite recording mode.
When the HDD property is set to redundancy, the video can be recorded both onto the redundancy HDD and the
R/W HDD simultaneously so as to ensure high security and reliability of video data.
Steps:
1. Enter the HDD Information interface.
Menu > HDD> General
2. Select HDD from the list and click the icon to enter the Local HDD Settings interface, as shown in
Figure 12. 15.
User Manual of Network Video Recorder
173
Figure 12. 15 Set HDD Property
3. Set the HDD property to R/W, Read-only or Redundancy.
4. Click the OK button to save the settings and exit the interface.
5. In the HDD Information menu, the HDD property will be displayed in the list.
At least 2 hard disks must be installed on your NVR when you want to set a HDD to Redundancy, and there is one
HDD with R/W property.
User Manual of Network Video Recorder
174
12.4 Configuring Quota Mode
Purpose:
Each camera can be configured with allocated quota for the storage of recorded files.
Steps:
1. Enter the Storage Mode interface.
Menu > HDD > Advanced
2. Set the Mode to Quota, as shown in Figure 12. 16.
The NVR must be rebooted to enable the changes to take effect.
Figure 12. 16 Storage Mode Settings Interface
3. Select a camera for which you want to configure quota.
4. Enter the storage capacity in the text fields of Max. Record Capacity (GB), as shown in Figure 12. 17.
Figure 12. 17 Configure Record Quota
5. You can copy the quota settings of the current camera to other cameras if required. Click the Copy button to
enter the Copy Camera menu, as shown in Figure 12. 18.
User Manual of Network Video Recorder
175
Figure 12. 18 Copy Settings to Other Camera(s)
6. Select the camera (s) to be configured with the same quota settings. You can also click the checkbox of IP
Camera to select all cameras.
7. Click the OK button to finish the Copy settings and back to the Storage Mode interface.
8. Click the Apply button to apply the settings.
If the quota capacity is set to 0, then all cameras will use the total capacity of HDD for record.
User Manual of Network Video Recorder
176
12.5 Checking HDD Status
Purpose:
You may check the status of the installed HDDs on NVR so as to take immediate check and maintenance in case
of HDD failure.
Checking HDD Status in HDD Information Interface
Steps:
1. Enter the HDD Information interface.
Menu > HDD>General
2. Check the status of each HDD which is displayed on the list, as shown in Figure 12. 19.
Figure 12. 19 View HDD Status (1)
If the status of HDD is Normal or Sleeping, it works normally. If the status is Uninitialized or Abnormal, please
initialize the HDD before use. And if the HDD initialization is failed, please replace it with a new one.
Checking HDD Status in HDD Information Interface
Steps:
1. Enter the System Information interface.
Menu >Maintenance > System Info
2. Click the HDD tab to view the status of each HDD displayed on the list, as shown in Figure 12. 20.
Figure 12. 20 View HDD Status (2)
User Manual of Network Video Recorder
177
12.6 HDD Detection
Purpose:
The device provides the HDD detection function such as the adopting of the S.M.A.R.T. and the Bad Sector
Detection technique. The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring
system for HDD to detect and report on various indicators of reliability in the hopes of anticipating failures.
S.M.A.R.T. Settings
Steps:
1. Enter the S.M.A.R.T Settings interface.
Menu > Maintenance >HDD Detect
2. Select the HDD to view its S.M.A.R.T information list, as shown in Figure 12. 21.
Figure 12. 21 S.M.A.R.T Settings Interface
The related information of the S.M.A.R.T. is shown on the interface.
You can choose the self-test types as Short Test, Expanded Test or the Conveyance Test.
Click the start button to start the S.M.A.R.T. HDD self-evaluation.
If you want to use the HDD even when the S.M.A.R.T. checking is failed, you can check the checkbox of the
Continue to use the disk when self-evaluation is failed item.
Bad Sector Detection
Steps:
1. Click the Bad Sector Detection tab.
2. Select the HDD No. in the dropdown list you want to configure, and choose All Detection or Key Area
Detection as the detection type.
3. Click the Detect button to start the detection.
User Manual of Network Video Recorder
178
Figure 12. 22 Bad Sector Detection
And you can click Error info button to see the detailed damage information.
And you can also pause/resume or cancel the detection.
User Manual of Network Video Recorder
179
12.7 Configuring HDD Error Alarms
Purpose:
You can configure the HDD error alarms when the HDD status is Uninitialized or Abnormal.
Steps:
1. Enter the Exception interface.
Menu > Configuration > Exceptions
2. Select the Exception Type to HDD Error from the dropdown list.
3. Click the checkbox(s) below to select the HDD error alarm type (s), as shown in Figure 12. 23.
The alarm type can be selected to: Audible Warning, Notify Surveillance Center, Send Email and Trigger Alarm
Output. Please refer to Chapter 8.6 Setting Alarm Response Actions.
Figure 12. 23 Configure HDD Error Alarm
4. When the Trigger Alarm Output is selected, you can also select the alarm output to be triggered from the list
below.
5. Click the Apply button to save the settings
User Manual of Network Video Recorder
180
Chapter 13 Camera Settings
User Manual of Network Video Recorder
181
13.1 Configuring OSD Settings
Purpose:
You can configure the OSD (On-screen Display) settings for the camera, including date /time, camera name, etc.
Steps:
1. Enter the OSD Configuration interface.
Menu > Camera > OSD
2. Select the camera to configure OSD settings.
3. Edit the Camera Name in the text field.
4. Configure the Display Name, Display Date and Display Week by clicking the checkbox.
5. Select the Date Format, Time Format and Display Mode.
Figure 13. 1 OSD Configuration Interface
6. You can use the mouse to click and drag the text frame on the preview window to adjust the OSD position.
7. Click the Apply button to apply the settings.
User Manual of Network Video Recorder
182
13.2 Configuring Privacy Mask
Purpose:
You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy
mask can prevent certain surveillance areas to be viewed or recorded.
Steps:
1. Enter the Privacy Mask Settings interface.
Menu > Camera >Privacy Mask
2. Select the camera to set privacy mask.
3. Click the checkbox of Enable Privacy Mask to enable this feature.
Figure 13. 2 Privacy Mask Settings Interface
4. Use the mouse to draw a zone on the window. The zones will be marked with different frame colors.
Up to 4 privacy masks zones can be configured and the size of each area can be adjusted.
5. The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear
Zone1-4 icons on the right side of the window, or click Clear All to clear all zones.
Figure 13. 3 Set Privacy Mask Area
6. Click the Apply button to save the settings.
User Manual of Network Video Recorder
183
13.3 Configuring Video Parameters
Steps:
1. Enter the Image Settings interface.
Menu > Camera >Image
Figure 13. 4 Image Settings Interface
2. Select the camera to set image parameters.
3. You can click on the arrow to change the value of each parameter.
4. Click the Apply button to save the settings.
User Manual of Network Video Recorder
184
Chapter 14 NVR Management and
Maintenance
User Manual of Network Video Recorder
185
14.1 Viewing System Information
Steps:
1. Enter the System Information interface.
Menu >Maintenance>System Info
2. You can click the Device Info, Camera, Record, Alarm, Network and HDD tabs to view the system
information of the device.
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
Figure 14. 1 Device Information Interface
User Manual of Network Video Recorder
186
14.2 Searching & Export Log Files
Purpose:
The operation, alarm, exception and information of the NVR can be stored in log files, which can be viewed and
exported at any time.
Steps:
1. Enter the Log Search interface.
Menu > Maintenance > Log Information
Figure 14. 2 Log Search Interface
2. Set the log search conditions to refine your search, including the Start Time, End Time, Major Type and
Minor Type.
3. Click the Search button to start search log files.
4. The matched log files will be displayed on the list shown below.
User Manual of Network Video Recorder
187
Figure 14. 3 Log Search Results
Up to 2000 log files can be displayed each time.
5. You can click the button of each log or double click it to view its detailed information, as shown in
Figure 14. 4. And you can also click the button to view the related video files if available.
Figure 14. 4 Log Details
6. If you want to export the log files, click the Export button on the Search Result interface to enter the Export
menu, as shown in Figure 14. 5.
User Manual of Network Video Recorder
188
Figure 14. 5 Export Log Files
7. Select the backup device from the dropdown list of Device Name.
8. Select the format of the log files to be exported. Up to 9 formats are selectable.
9. Click the Export to export the log files to the selected backup device.
You can click the New Folder button to create new folder in the backup device, or click the Format button
to format the backup device before log export.
Please connect the backup device to NVR before operating log export.
User Manual of Network Video Recorder
189
14.3 Importing/Exporting IP Camera Info
Purpose:
The information of added IP camera can be generated into an excel file and exported to the local device for backup,
including the IP address, manage port, password of admin, etc.. And the exported file can be edited on your PC,
like adding or deleting the content, and copy the setting to other devices by importing the excel file to it.
Steps:
1. Enter the camera management interface.
Menu > Camera > IP Camera Import/Export
2. Click the IP Camera Import/Export tab, the content of detected plugged external device appears.
3. Click the Export button to export configuration files to the selected local backup device.
4. To import a configuration file, select the file from the selected backup device and click the Import button.
After the importing process is completed, you must reboot the NVR.
User Manual of Network Video Recorder
190
14.4 Importing/Exporting Configuration Files
Purpose:
The configuration files of the NVR can be exported to local device for backup; and the configuration files of one
NVR can be imported to multiple NVR devices if they are to be configured with the same parameters.
Steps:
1. Enter the Import/Export Configuration File interface.
Menu > Maintenance >Import/Export
Figure 14. 6 Import/Export Config File
2. Click the Export button to export configuration files to the selected local backup device.
3. To import a configuration file, select the file from the selected backup device and click the Import button.
After the import process is completed, you must reboot the NVR.
After having finished the import of configuration files, the device will reboot automatically.
User Manual of Network Video Recorder
191
14.5 Upgrading System
Purpose:
The firmware on your NVR can be upgraded by local backup device or remote FTP server.
14.5.1 Upgrading by Local Backup Device
Steps:
1. Connect your NVR with a local backup device where the update firmware file is located.
2. Enter the Upgrade interface.
Menu >Maintenance>Upgrade
3. Click the Local Upgrade tab to enter the local upgrade menu, as shown in Figure 14. 7.
Figure 14. 7 Local Upgrade Interface
4. Select the update file from the backup device.
5. Click the Upgrade button to start upgrading.
6. After the upgrading is complete, reboot the NVR to activate the new firmware.
14.5.2 Upgrading by FTP
Purpose:
Ensure the network connection of the PC (running FTP server) and the device is valid and correct. Run the FTP
server on the PC and copy the firmware into the corresponding directory of your PC.
Refer to the user manual of the FTP server to set the FTP server on your PC and put the firmware file into the
User Manual of Network Video Recorder
192
directory as required.
Steps:
1. Enter the Upgrade interface.
Menu >Maintenance>Upgrade
2. Click the FTP tab to enter the local upgrade interface, as shown in Figure 14. 8.
Figure 14. 8 FTP Upgrade Interface
3. Enter the FTP Server Address in the text field.
4. Click the Upgrade button to start upgrading.
5. After the upgrading is complete, reboot the NVR to activate the new firmware.
User Manual of Network Video Recorder
193
14.6 Restoring Default Settings
Steps:
1. Enter the Default interface.
Menu > Maintenance > Default
Figure 14. 9 Restore Defaults
2. Select the restoring type from the following three options.
Restore Defaults: Restore all parameters, except the network (including IP address, subnet mask, gateway, MTU,
NIC working mode, default route, server port, etc.) and user account parameters, to the factory default settings.
Factory Defaults: Restore all parameters to the factory default settings.
Restore to Inactive: Restore the device to the inactive status.
3. Click the OK button to restore the default settings.
The device will reboot automatically after restoring to the default settings.
User Manual of Network Video Recorder
194
Chapter 15 Others
User Manual of Network Video Recorder
195
15.1 Configuring RS-232 Serial Port
The RS-232 is provided by the DS-8600NI-E8 and DS-7700NI-E4 series NVR only.
Purpose:
The RS-232 port can be used in two ways:
Parameters Configuration: Connect a PC to the NVR through the PC serial port. Device parameters can be
configured by using software such as HyperTerminal. The serial port parameters must be the same as the
NVR’s when connecting with the PC serial port.
Transparent Channel: Connect a serial device directly to the NVR. The serial device will be controlled
remotely by the PC through the network and the protocol of the serial device.
Steps:
1. Enter the RS-232 Settings interface.
Menu >Configuration> RS-232
Figure 15. 1 RS-232 Settings Interface
2. Configure RS-232 parameters, including baud rate, data bit, stop bit, parity, flow control and usage.
3. Click the Apply button to save the settings.
User Manual of Network Video Recorder
196
15.2 Configuring General Settings
Purpose:
You can configure the BNC output standard, VGA output resolution, mouse pointer speed through the Menu >
Configuration > General interface.
Steps:
1. Enter the General Settings interface.
Menu >Configuration> General
2. Select the General tab.
Figure 15. 2 General Settings Interface
3. Configure the following settings:
Language: The default language used is English.
Resolution: Select the resolution for the video output, which must be the same with the resolution of the
monitor screen.
Time Zone: Select the time zone.
Date Format: Select the date format.
System Date: Select the system date.
System Time: Select the system time.
Mouse Pointer Speed: Set the speed of mouse pointer; 4 levels are configurable.
Enable Wizard: Enable/disable the Wizard when the device starts up.
Enable Password: Enable/disable the use of the login password.
4. Click the Apply button to save the settings.
User Manual of Network Video Recorder
197
15.3 Configuring DST Settings
Steps:
1. Enter the General Settings interface.
Menu >Configuration>General
2. Choose DST Settings tab.
Figure 15. 3 DST Settings Interface
You can check the checkbox before the Auto DST Adjustment item.
Or you can manually check the Enable DST checkbox, and then you choose the date of the DST period.
User Manual of Network Video Recorder
198
15.4 Configuring More Settings for Device
Parameters
Steps:
1. Enter the General Settings interface.
Menu >Configuration>General
2. Click the More Settings tab to enter the More Settings interface, as shown in Figure 15. 4.
Figure 15. 4 More Settings Interface
3. Configure the following settings:
Device Name: Edit the name of NVR.
Device No.: Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the
default No. is 255. The number is used for the remote and keyboard control.
Auto Logout: Set timeout time for menu inactivity. E.g., when the timeout time is set to 5 Minutes, then
the system will exit from the current operation menu to live view screen after 5 minutes of menu
inactivity.
Menu Output Mode: You can choose the menu display on different video output. By default, only
HDMI
TM
/VGA is selectable.
4. Click the Apply button to save the settings.
User Manual of Network Video Recorder
199
15.5 Managing User Accounts
Purpose:
There is a default account in the NVR: Administrator. The Administrator user name is admin and the password is
set when you start the device for the first time. The Administrator has the permission to add and delete user and
configure user parameters.
15.5.1 Adding a User
Steps:
1. Enter the User Management interface.
Menu >Configuration>User
Figure 15. 5 User Management Interface
2. Click the Add button to enter the Add User interface.
Figure 15. 6 Add User Menu
3. Enter the information for new user, including User Name, Password, Confirm, Level and User’s MAC
User Manual of Network Video Recorder
200
Address.
Password: Set the password for the user account.
STRONG PASSWORD RECOMMENDED We highly recommend you create a strong
password of your own choosing (using a minimum of 8 characters, including upper case letters,
lower case letters, numbers, and special characters) in order to increase the security of your
product. And we recommend you reset your password regularly, especially in the high security
system, resetting the password monthly or weekly can better protect your product.
Level: Set the user level to Operator or Guest. Different user levels have different operating permission.
Operator: The Operator user level has permission of Two-way Audio in Remote Configuration and all
operating permission in Camera Configuration by default.
Guest: The Guest user has no permission of Two-way Audio in Remote Configuration and only has the
local/remote playback in the Camera Configuration by default.
User’s MAC Address: The MAC address of the remote PC which logs onto the NVR. If it is configured and
enabled, it only allows the remote user with this MAC address to access the NVR.
4. Click the OK button to save the settings and go back to the User Management interface. The added new user
will be displayed on the list, as shown in Figure 15. 7.
Figure 15. 7 Added User Listed in User Management Interface
5. Select the user from the list and then click the button to enter the Permission settings interface, as shown in
Figure 15. 8.
Figure 15. 8 User Permission Settings Interface
User Manual of Network Video Recorder
201
6. Set the operating permission of Local Configuration, Remote Configuration and Camera Configuration for
the user.
Local Configuration
Local Log Search: Searching and viewing logs and system information of NVR.
Local Parameters Settings: Configuring parameters, restoring factory default parameters and
importing/exporting configuration files.
Local Camera Management: The adding, deleting and editing of IP cameras.
Local Advanced Operation: Operating HDD management (initializing HDD, setting HDD property),
upgrading system firmware, clearing I/O alarm output.
Local Shutdown Reboot: Shutting down or rebooting the NVR.
Remote Configuration
Remote Log Search: Remotely viewing logs that are saved on the NVR.
Remote Parameters Settings: Remotely configuring parameters, restoring factory default parameters and
importing/exporting configuration files.
Remote Camera Management: Remote adding, deleting and editing of the IP cameras.
Remote Serial Port Control: Configuring settings for RS-232 and RS-485 ports.
Remote Video Output Control: Sending remote button control signal.
Two-Way Audio: Realizing two-way radio between the remote client and the NVR.
Remote Alarm Control: Remotely arming (notify alarm and exception message to the remote client) and
controlling the alarm output.
Remote Advanced Operation: Remotely operating HDD management (initializing HDD, setting HDD
property), upgrading system firmware, clearing I/O alarm output.
Remote Shutdown/Reboot: Remotely shutting down or rebooting the NVR.
Camera Configuration
Remote Live View: Remotely viewing live video of the selected camera (s).
Local Manual Operation: Locally starting/stopping manual recording and alarm output of the selected
camera (s).
Remote Manual Operation: Remotely starting/stopping manual recording and alarm output of the
selected camera (s).
Local Playback: Locally playing back recorded files of the selected camera (s).
Remote Playback: Remotely playing back recorded files of the selected camera (s).
Local PTZ Control: Locally controlling PTZ movement of the selected camera (s).
Remote PTZ Control: Remotely controlling PTZ movement of the selected camera (s).
Local Video Export: Locally exporting recorded files of the selected camera (s).
7. Click the OK button to save the settings and exit interface.
Only the admin user account has the permission of restoring factory default parameters.
15.5.2 Deleting a User
Steps:
1. Enter the User Management interface.
Menu >Configuration>User
2. Select the user to be deleted from the list, as shown in Figure 15. 9.
User Manual of Network Video Recorder
202
Figure 15. 9 User List
3. Click the icon to delete the selected user account.
15.5.3 Editing a User
For the added user accounts, you can edit the parameters.
Steps:
1. Enter the User Management interface.
Menu >Configuration>User
2. Select the user to be edited from the list, as shown in Figure 15. 9.
3. Click the icon to enter the Edit User interface, as shown in Figure 15. 10.
Figure 15. 10 Edit User Interface
4. Edit the corresponding parameters.
Operator and Guest
You can edit the user information, including user name, password, permission level and MAC address.
Check the checkbox of Change Password if you want to change the password, and input the new
password in the text field of Password and Confirm. A strong password is recommended.
Admin
You are only allowed to edit the password and MAC address. Check the checkbox of Change Password
if you want to change the password, and the input the correct old password, and the new password in the
text field of Password and Confirm.
User Manual of Network Video Recorder
203
STRONG PASSWORD RECOMMENDED We highly recommend you create a strong
password of your own choosing (using a minimum of 8 characters, including upper case letters,
lower case letters, numbers, and special characters) in order to increase the security of your
product. And we recommend you reset your password regularly, especially in the high security
system, resetting the password monthly or weekly can better protect your product.
5. Click the OK button to save the settings and exit the menu.
6. For the Operator or Guest user account, you can also click the button on te user management interface
to edit the permission.
User Manual of Network Video Recorder
204
Chapter 16 Appendix
User Manual of Network Video Recorder
205
16.1 Glossary
Dual Stream: Dual stream is a technology used to record high resolution video locally while transmitting
a lower resolution stream over the network. The two streams are generated by the DVR, with the main
stream having a maximum resolution of 4CIF and the sub-stream having a maximum resolution of CIF.
HDD: Acronym for Hard Disk Drive. A storage medium which stores digitally encoded data on platters
with magnetic surfaces.
DHCP: Dynamic Host Configuration Protocol (DHCP) is a network application protocol used by devices
(DHCP clients) to obtain configuration information for operation in an Internet Protocol network.
HTTP: Acronym for Hypertext Transfer Protocol. A protocol to transfer hypertext request and information
between servers and browsers over a network
PPPoE: PPPoE, Point-to-Point Protocol over Ethernet, is a network protocol for encapsulating
Point-to-Point Protocol (PPP) frames inside Ethernet frames. It is used mainly with ADSL services where
individual users connect to the ADSL transceiver (modem) over Ethernet and in plain Metro Ethernet
networks.
DDNS: Dynamic DNS is a method, protocol, or network service that provides the capability for a
networked device, such as a router or computer system using the Internet Protocol Suite, to notify a
domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured
hostnames, addresses or other information stored in DNS.
Hybrid DVR: A hybrid DVR is a combination of a DVR and NVR.
NTP: Acronym for Network Time Protocol. A protocol designed to synchronize the clocks of computers
over a network.
NTSC: Acronym for National Television System Committee. NTSC is an analog television standard used
in such countries as the United States and Japan. Each frame of anNTSC signal contains 525 scan lines at
60Hz.
NVR: Acronym for Network Video Recorder. An NVR can be a PC-based or embedded system used for
centralized management and storage for IP cameras, IP Domes and other DVRs.
PAL: Acronym for Phase Alternating Line. PAL is also another video standard used in broadcast
televisions systems in large parts of the world. PAL signal contains 625 scan lines at 50Hz.
PTZ: Acronym for Pan, Tilt, Zoom. PTZ cameras are motor driven systems that allow the camera to pan
left and right, tilt up and down and zoom in and out.
USB: Acronym for Universal Serial Bus. USB is a plug-and-play serial bus standard to interface devices to
a host computer.
User Manual of Network Video Recorder
206
16.2 Troubleshooting
No image displayed on the monitor after starting up normally.
Possible Reasons
a) No VGA or HDMI
TM
connections.
b) Connection cable is damaged.
c) Input mode of the monitor is incorrect.
Steps
1. Verify the device is connected with the monitor via HDMI
TM
or VGA cable.
If not, please connect the device with the monitor and reboot.
2. Verify the connection cable is good.
If there is still no image display on the monitor after rebooting, please check if the connection cable is
good, and change a cable to connect again.
3. Verify Input mode of the monitor is correct.
Please check the input mode of the monitor matches with the output mode of the device (e.g. if the
output mode of NVR is HDMI
TM
output, then the input mode of monitor must be the HDMI
TM
input).
And if not, please modify the input mode of monitor.
4. Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
There is an audible warning sound “Di-Di-Di-DiDi” after a new bought NVR starts up.
Possible Reasons
a) No HDD is installed in the device.
b) The installed HDD has not been initialized.
c) The installed HDD is not compatible with the NVR or is broken-down.
Steps
1. Verify at least one HDD is installed in the NVR.
1) If not, please install the compatible HDD.
Please refer to the “Quick Operation Guide” for the HDD installation steps.
2) If you don’t want to install a HDD, select “Menu>Configuration > Exceptions”, and uncheck the
Audible Warning checkbox of “HDD Error”.
2. Verify the HDD is initialized.
1) Select “Menu>HDD>General”.
2) If the status of the HDD is “Uninitialized”, please check the checkbox of corresponding HDD and
click the “Init” button.
3. Verify the HDD is detected or is in good condition.
1) Select “Menu>HDD>General”.
2) If the HDD is not detected or the status is “Abnormal”, please replace the dedicated HDD according
to the requirement.
4. Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
The status of the added IP camera displays as “Disconnected” when it is connected through Private
Protocol. Select “Menu>Camera>Camera>IP Camera” to get the camera status.
User Manual of Network Video Recorder
207
Possible Reasons
a) Network failure, and the NVR and IP camera lost connections.
b) The configured parameters are incorrect when adding the IP camera.
c) Insufficient bandwidth.
Steps
1. Verify the network is connected.
1) Connect the NVR and PC with the RS-232 cable.
2) Open the Super Terminal software, and execute the ping command. Input “ping IP” (e.g. ping
172.6.22.131).
Simultaneously press Ctrl and C to exit the ping command.
If there exists return information and the time value is little, the network is normal.
2. Verify the configuration parameters are correct.
1) Select “Menu>Camera>Camera>IP Camera”.
2) Verify the following parameters are the same with those of the connected IP devices, including IP
address, protocol, management port, user name and password.
3. Verify the whether the bandwidth is enough.
1) Select “Menu >Maintenance > Net Detect > Network Stat.”.
2) Check the usage of the access bandwidth, and see if the total bandwidth has reached its limit.
4. Check if the fault is solved by the step 1 to step 3.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
The IP camera frequently goes online and offline and the status of it displays as “Disconnected”.
Possible Reasons
a) The IP camera and the NVR versions are not compatible.
b) Unstable power supply of IP camera.
c) Unstable network between IP camera and NVR.
d) Limited flow by the switch connected with IP camera and NVR.
Steps
1. Verify the IP camera and the NVR versions are compatible.
1) Enter the IP camera Management interface “Menu > Camera > Camera>IP Camera”, and view the
firmware version of connected IP camera.
2) Enter the System Info interface “Menu>Maintenance>System Info>Device Info”, and view the
firmware version of NVR.
2. Verify power supply of IP camera is stable.
1) Verify the power indicator is normal.
2) When the IP camera is offline, please try the ping command on PC to check if the PC connects with
the IP camera.
3. Verify the network between IP camera and NVR is stable.
1) When the IP camera is offline, connect PC and NVR with the RS-232 cable.
2) Open the Super Terminal, use the ping command and keep sending large data packages to the
connected IP camera, and check if there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
Example: Input ping 172.6.22.131 l 1472 f.
4. Verify the switch is not flow control.
User Manual of Network Video Recorder
208
Check the brand, model of the switch connecting IP camera and NVR, and contact with the manufacturer
of the switch to check if it has the function of flow control. If so, please turn it down.
5. Check if the fault is solved by the step 1 to step 4.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
No monitor connected with the NVR locally and when you manage the IP camera to connect with the
device by web browser remotely, of which the status displays as Connected. And then you connect the
device with the monitor via VGA or HDMI
TM
interface and reboot the device, there is black screen with
the mouse cursor.
Connect the NVR with the monitor before startup via VGA or HDMI
TM
interface, and manage the IP
camera to connect with the device locally or remotely, the status of IP camera displays as Connect.
Possible Reasons:
After connecting the IP camera to the NVR, the image is output via the main spot interface by default.
Steps:
1. Enable the output channel.
2. Select “Menu > Configuration > Live View > View”, and select video output interface in the drop-down
list and configure the window you want to view.
The view settings can only be configured by the local operation of NVR.
Different camera orders and window-division modes can be set for different output interfaces
separately, and digits like “D1”and “D2” stands for the channel number, and “X” means the selected
window has no image output.
3. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
Live view stuck when video output locally.
Possible Reasons:
a) Poor network between NVR and IP camera, and there exists packet loss during the transmission.
b) The frame rate has not reached the real-time frame rate.
Steps:
1. Verify the network between NVR and IP camera is connected.
1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232
cable.
2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 l 1472 f (the IP address
may change according to the real condition), and check if there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
2. Verify the frame rate is real-time frame rate.
Select “Menu > Record > Parameters > Record”, and set the Frame rate to Full Frame.
3. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
Live view stuck when video output remotely via the Internet Explorer or platform software.
Possible Reasons:
a) Poor network between NVR and IP camera, and there exists packet loss during the transmission.
b)Poor network between NVR and PC, and there exists packet loss during the transmission.
User Manual of Network Video Recorder
209
c) The performances of hardware are not good enough, including CPU, memory, etc..
Steps:
1. Verify the network between NVR and IP camera is connected.
1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232
cable.
2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 l 1472 f (the IP address
may change according to the real condition), and check if there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
2. Verify the network between NVR and PC is connected.
1) Open the cmd window in the Start menu, or you can press “windows+R” shortcut key to open it.
2) Use the ping command to send large packet to the NVR, execute the command of “ping
192.168.0.0 l 1472 –f” (the IP address may change according to the real condition), and check if
there exists packet loss.
Simultaneously press Ctrl and C to exit the ping command.
3. Verify the hardware of the PC is good enough.
Simultaneously press Ctrl, Alt and Delete to enter the windows task management interface, as shown in
the following figure.
Windows task management interface
Select the “Performance” tab; check the status of the CPU and Memory.
If the resource is not enough, please end some unnecessary processes.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
When using the NVR to get the live view audio, there is no sound or there is too much noise, or the
volume is too low.
Possible Reasons:
a) Cable between the pickup and IP camera is not connected well; impedance mismatches or incompatible.
b) The stream type is not set as “Video & Audio”.
User Manual of Network Video Recorder
210
c) The encoding standard is not supported with NVR.
Steps:
1. Verify the cable between the pickup and IP camera is connected well; impedance matches and
compatible.
Log in the IP camera directly, and turn the audio on, check if the sound is normal. If not, please contact
the manufacturer of the IP camera.
2. Verify the setting parameters are correct.
Select “Menu > Record > Parameters > Record”, and set the Stream Type as “Audio & Video”.
3. Verify the audio encoding standard of the IP camera is supported by the NVR.
NVR supports G722.1 and G711 standards, and if the encoding parameter of the input audio is not one of
the previous two standards, you can log in the IP camera to configure it to the supported standard.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
The image gets stuck when NVR is playing back by single or multi-channel.
Possible Reasons:
a) Poor network between NVR and IP camera, and there exists packet loss during the transmission.
b) The frame rate is not the real-time frame rate.
c) The NVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a
16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads to
a slight stuck.
Steps:
1. Verify the network between NVR and IP camera is connected.
1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232
cable.
2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 l 1472 f (the IP address
may change according to the real condition), and check if there exists packet loss.
Simultaneously press the Ctrl and C to exit the ping command.
2. Verify the frame rate is real-time frame rate.
Select “Menu > Record > Parameters > Record”, and set the Frame Rate to “Full Frame”.
3. Verify the hardware can afford the playback.
Reduce the channel number of playback.
Select “Menu > Record > Encoding > Record”, and set the resolution and bitrate to a lower level.
4. Reduce the number of local playback channel.
Select “Menu > Playback”, and uncheck the checkbox of unnecessary channels.
5. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
No record file found in the NVR local HDD, and prompt “No record file found”.
Possible Reasons:
a) The time setting of system is incorrect.
b) The search condition is incorrect.
c) The HDD is error or not detected.
User Manual of Network Video Recorder
211
Steps:
1. Verify the system time setting is correct.
Select “Menu > Configuration > General > General”, and verify the “Device Time” is correct.
2. Verify the search condition is correct.
Select “Playback”, and verify the channel and time are correct.
3. Verify the HDD status is normal.
Select “Menu > HDD > General” to view the HDD status, and verify the HDD is detected and can be
read and written normally.
4. Check if the fault is solved by the above steps.
If it is solved, finish the process.
If not, please contact the engineer from our company to do the further process.
User Manual of Network Video Recorder
212
16.3 Summary of Changes
Version 3.3.2
Added:
1. Support H.264+. (Product Key Features, Chapter 3.2.4, Chapter 5.1)
Version 3.3.0
Added:
2. Support vehicle detection of VCA alarm. (Chapter 9.2)
3. Support plate search. (Chapter 10.3)
4. Set the strong password to activate the device is needed for the first-time startup (Chapter 2.2)
Updated:
1. Optimize the adding of IP camera. (Chapter 2.5)
2. Optimize the DDNS configuration. (Chapter 11.2.3)
3. Three methods are selectable for restoring to the default settings. (Chapter 14.6)
4. Optimize the user account management. (Chapter 15.5)
Version 3.2.0
Added
5. Support play back by sub-periods. (Chapter 6.1.6)
6. Support VCA alarm for up to 15 VCA detections. (Chapter 9)
7. Support VCA search function for behavior search, face search, people counting and heat map. (Chapter 10)
8. Support up to 9 formats for selection when you export the files to storage device. (Chapter 7)
9. The prompt will pop up when you input wrong user name or password in login interface.(Chapter 2.2)
10. The continent/country is selectable for the HiDDNS settings. (Chapter 11.2.2)
Update:
5. Optimize the interface of right-click menu. (Chapter 3.2.2)
6. Optimize the interface of PTZ control panel. (Chapter 4)
7. Optimize the interface of record parameters. (Chapter 5)
8. Update the interface of recording schedule. (Chapter 5)
9. Optimize the Device Info interface by adding QR Code. (Chapter 16.1)
Version 3.0.6
Updated
1. Optimize the PTZ control panels and operations. (Chapter 4)
2. Change the ezviz Cloud to EZVIZ Cloud P2P. (Chapter 9.2.2)
3. Add the models of DS-7100NI series, DS-7600NI-SE series and DS-7600NI-V(P) series NVR.
Version 3.0.4
Added
1. Connectable to smart IP cameras, and VCA alarm detection and recording are supported. (Chapter 5.2, Chapter
5.5 and Chapter 8.5)
User Manual of Network Video Recorder
213
2. Support video searching, playing back and backing up by VCA events. (Chapter 6.1.3 and Chapter 7.1.3)
3. Support smart playback by VCA rules. (Chapter 6.1.5)
4. Support P2P protocol and access by ezviz. (Chapter 9.2.2)
Deleted
Combine the smart search function with the smart playback function, and the smart search section is deleted.
(Chapter 6.2.2 Smart Search)
User Manual of Network Video Recorder
214
16.4 List of Compatible IP Cameras
16.4.1 List of Hikvision IP Cameras
For the list, our company holds right to interpret.
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
SD
Network
Camera
DS-2CD7133F-E
V5.2.0 build 140721
640*480
×
DS-2CD793NFWD-EI
V5.2.0 build 140721
704*576
DS-2CD802NF
V2.0 build 090522
704*576
V2.0 build 090715
V2.0 build 110301
DS-2CD833F-E
V5.2.0 build 140721
640*480
DS-2CD893PF-E
V5.2.0 build 140721
704*576
HD
Network
Camera
DS-2CD2012-I
V5.3.0 build150327
1280*960
×
DS-2CD2132-I
V5.3.0 build150327
2048*1536
×
DS-2CD2410FD-I(W)
V5.3.0 build150327
1920*1080
DS-2CD2612F-I
V5.3.0 build150327
1280*960
×
DS-2CD2612F-IS
V5.3.0 build150327
1280*960
DS-2CD2632F-I
V5.3.0 build150327
2048*1536
×
DS-2CD2632F-IS
V5.3.0 build150327
2048*1536
DS-2CD2710F-I
V5.3.0 build150327
1920*1080
×
DS-2CD2720F-I
V5.3.0 build150327
1920*1080
×
DS-2CD4010F
V5.3.0 build150327
1920*1080
DS-2CD4012F
V5.3.0 build150327
1280*1024
DS-2CD4026FWD
V5.3.0 build150327
1920*1080
DS-2CD4026FWD-SDI
V5.3.0 build150327
1920*1080
DS-2CD4032FWD
V5.3.0 build150327
2048*1536
DS-2CD4065F
V5.3.0 build150327
3072*2048
DS-2CD4124F-I(2.8-12mm)
V5.3.0 build150327
1920*1080
DS-2CD4132FWD-I(2.8-12mm)
V5.3.0 build150327
2048*1536
DS-2CD4212F-I(2.8-12mm)
V5.3.0 build150327
1280*1024
×
DS-2CD4212F-IS(2.8-12mm)
V5.3.0 build150327
1280*1024
DS-2CD4212FWD-I
V5.3.0 build150327
1280*960
×
DS-2CD4212FWD-IS
V5.3.0 build150327
1280*960
DS-2CD4224F-I
V5.3.0 build150327
1920*1080
×
DS-2CD4232FWD-I
V5.3.0 build150327
2048*1536
×
DS-2CD4232FWD-IS(2.8-12mm)
V5.3.0 build150327
2048*1536
DS-2CD4312F-I
V5.3.0 build150327
1280*1024
×
User Manual of Network Video Recorder
215
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
DS-2CD4312FWD-I
V5.3.0 build150327
1280*960
×
DS-2CD4324F-I
V5.3.0 build150327
1920*1080
×
DS-2CD4332FHWD-IS
V5.3.0 build150327
2048*1536
DS-2CD4332FHWD-I
V5.3.0 build150327
2048*1536
×
DS-2CD4332FWD-I
V5.3.0 build150327
2048*1536
×
DS-2CD6213F
V5.2.6 build 141218
1280*960
×
DS-2CD6223F
V5.2.6 build 141218
1920*1080
×
DS-2CD6233F
V5.2.6 build 141218
2048*1536
×
DS-2CD7153-E
V5.2.0 build 140721
1600*1200
×
DS-2CD7164-E
V5.2.0 build 140721
1280*720
×
DS_2CD754F-EI
V5.2.0 build 140721
2048*1536
DS-2CD754FWD-E
V5.2.0 build 140721
1920*1080
DS-2CD754FWD-EIZ
V5.2.0 build 140721
2048*1536
DS_2CD783F-EI
V5.2.0 build 140721
2560*1920
DS-2CD8153F-E
V5.2.0 build 140721
1600*1200
DS-2CD8464F-EI
V5.2.0 build 140721
1280*960
DS-2CD852MF-E
V2.0 build 110614
1600*1200
V2.0 build 110426
V2.0 build 100521
DS-2CD855F-E
V5.2.0 build 140721
1920*1080
DS-2CD862MF-E
V2.0 build 110614
1280*960
V2.0 build 110426
V2.0 build 100521
DS-2CD863PF/NF-E
V5.2.0 build 140721
1280*960
DS-2CD864FWD-E
V5.2.0 build 140721
1280*720
DS-2CD876MF/BF-E
V4.0.3 build120913
1600*1200
DS-2CD877BF
V4.0.3 build120913
1920*1080
DS-2CD886MF-E
V4.0.3 build 120913
2560*1920
DS-2CD966(B)
V3.1 build 120423
1360*1024
×
×
DS-2CD966-V(B)
V3.1 build 120423
1360*1024
×
×
DS-2CD976(C)
V3.1 build 120423
1600*1200
×
×
DS-2CD976-V(C)
V3.1 build 120423
1600*1200
×
×
DS-2CD977(C)
V3.1 build 120423
1920*1080
×
×
DS-2CD986A(C)
V3.1 build 120423
2448*2048
×
×
DS-2CD986CB
V2.3.6 build 120401
2560*1920
×
×
HD
Network
Camera
DS-2CD9122
V3.7.1 build140417
1920*1080
×
DS-2CD9152
V3.7.1 build140417
2560*1920
×
iDS-2CD9152
V3.7.1 build140417
2560*1920
×
DS-2CD9122-H
V3.7.1 build140417
1920*1080
×
DS-2CD9182-H
V3.8.1 build140815
3296*2472
×
DS-2CD9121
V3.7.1 build140417
1600*1200
×
User Manual of Network Video Recorder
216
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
iDS-2CD9121
V3.7.1 build140417
1600*1200
×
DS-2CD9131
V4.0.0 build150213
2048*1536
×
iDS-2CD9131
V4.0.0 build150213
2048*1536
×
DS-2CD9121A
V3.8.2 build141121
1600*1200
×
iDS-2CD9121A
V3.8.2 build141121
1600*1200
×
DS-2CD9111(B)
V3.7.1 build140417
1360*1024
×
DS-2CD9151A
V3.8.2 build141121
2448*2048
×
DS-2CD9152-H
V3.8.2 build141121
2592*2048
×
iDS-2CD9282
V3.8.2 build141121
3296*2472
×
DS-2CD9131-K
V4.0.0 build150213
2048*1536
DS-2CD9152-HK
V3.8.2 build141121
2592*2048
iDS-2CD9131-E
V3.8.2 build141121
2048*1536
×
iDS-2CD9151A-E
V3.8.2 build141121
2448*2048
×
iDS-2CD9151A
V3.8.2 build141121
2448*2048
×
iDS-2CD9152-EH
V3.8.2 build141121
2592*2048
×
iDS-2CD9152-H
V3.8.2 build141121
2592*2048
×
DS-2CD9120-H
V3.7.1 build140417
1600*1200
×
iDS-2CD9361
V4.0.0 build150213
2752*2208
×
iDS-2CD9022
V4.0.0 build150213
1920*1080
iDS-2CD9025
V3.8.2 build141114
1920*1080
×
iDS-2CD9022-SZ
V4.0.0 build150213
1920*1080
×
DS-2CD9125-KS
V3.8.1 build150113
1920*1080
×
SD Encoder
DS-6501HCI
V1.0.1 build130607
352*288
DS-6501HCI-SATA
V1.0.1 build130607
352*288
DS-6501HFI
V1.0.1 build130607
704*576
DS-6501HFI- SATA
V1.0.1 build130607
704*576
DS-6502HCI
V1.0.1 build130607
352*288
DS-6502HCI- SATA
V1.0.1 build130607
352*288
DS-6502HFI
V1.0.1 build130607
704*576
DS-6502HFI- SATA
V1.0.1 build130607
704*576
DS-6504HCI
V1.0.1 build130607
352*288
DS-6504HCI- SATA
V1.0.1 build130607
352*288
DS-6504HFI
V1.0.1 build130607
704*576
DS-6504HFI- SATA
V1.0.1 build130607
704*576
DS-6508HCI
V1.0.1 build130607
352*288
DS-6508HCI- SATA
V1.0.1 build130607
352*288
DS-6508HFI
V1.0.1 build130607
704*576
DS-6508HFI- SATA
V1.0.1 build130607
704*576
DS-6516HCI
V1.0.1 build130607
352*288
DS-6516HCI- SATA
V1.0.1 build130607
352*288
DS-6516HFI
V1.0.1 build130607
704*576
User Manual of Network Video Recorder
217
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
DS-6516HFI- SATA
V1.0.1 build130607
704*576
DS-6601HCI
V1.2.1 build131202
352*288
DS-6602HCI
V1.2.1 build131202
352*288
DS-6604HCI
V1.2.1 build131202
352*288
DS-6601HFI(-SATA)
V1.2.1 build131202
704*576
DS-6602HFI(SATA)
V1.2.1 build131202
704*576
DS-6604HFI(-SATA)
V1.2.1 build131202
704*576
DS-6701HWI
V1.2.3 build141202
960*576
DS-6701HWI-SATA
V1.2.3 build141202
960*576
DS-6704HWI
V1.2.3 build141202
960*576
DS-6704HWI-SATA
V1.2.3 build141202
960*576
DS-6708HWI
V1.2.3 build141202
960*576
DS-6708HWI-SATA
V1.2.3 build141202
960*576
DS-6716HWI
V1.2.3 build141202
960*576
DS-6716HWI-SATA
V1.2.3 build141202
960*576
HD
Encoder
DS-6601HFHI
V1.1.0 build150123
1920*1080
DS-6601HFHI/L
V1.1.0 build150123
1920*1080
Network
Speed
Dome
DS-2DF7274-A/D/AF
V5.2.8 build150124
1280*960
iDS-2DF7274-A/D/AF
V5.2.8 build150124
1280*960
DS-2DM7274-A
V5.2.8 build150124
1280*960
DS-2DF5274-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1280*960
iDS-2DF5274-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1280*960
DS-2DM5274-A/A3
V5.2.8 build150124
1280*960
DS-2DF7276-A/D/AF
V5.2.8 build150124
1280*960
iDS-2DF7276-A/D/AF
V5.2.8 build150124
1280*960
DS-2DF5276-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1280*960
iDS-2DF5276-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1280*960
DS-2DF7274-AH/DH/AFH
V5.2.8 build150124
1280*960
iDS-2DF7274-AH/DH/AFH
V5.2.8 build150124
1280*960
DS-2DF5274-AH/DH/A3H/D3H/AFH/A3FH
V5.2.8 build150124
1280*960
iDS-2DF5274-AH/DH/A3H/D3H/AFH/A3FH
V5.2.8 build150124
1280*960
DS-2DF7276-AH/DH/AFH
V5.2.8 build150124
1280*960
iDS-2DF7276-AH/DH/AFH
V5.2.8 build150124
1280*960
DS-2DF5276-AH/DH/A3H/D3H/AFH/A3FH
V5.2.8 build150124
1280*960
iDS-2DF5276-AH/DH/A3H/D3H/AFH/A3FH
V5.2.8 build150124
1280*960
DS_2DF7130I5-AW
V5.2.8 build150124
1280*960
DS-2DF7285-AH
V5.2.8 build150124
1920*1080
DS-2DF5285-AH
V5.2.8 build150124
1920*1080
DS-2DF7294-A/D/AF
V5.2.8 build150124
2048*1536
iDS-2DF7294-A/D/AF
V5.2.8 build150124
2048*1536
DS-2DF5294-A/D/A3/D3/AF/A3F
V5.2.8 build150124
2048*1536
User Manual of Network Video Recorder
218
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
iDS-2DF5294-A/D/A3/D3/AF/A3F
V5.2.8 build150124
2048*1536
DS-2DF7296-A/D/AF
V5.2.8 build150124
2048*1536
iDS-2DF7296-A/D/AF
V5.2.8 build150124
2048*1536
DS-2DF5296-A/D/A3/D3/AF/A3F
V5.2.8 build150124
2048*1536
iDS-2DF5296-A/D/A3/D3/AF/A3F
V5.2.8 build150124
2048*1536
DS-2DF6223-A
V5.2.8 build150124
1920*1080
iDS-2DF6223-A
V5.2.8 build150124
1920*1080
DS-2DF8223i-A
V5.2.8 build150124
1920*1080
iDS-2DF8223i-A
V5.2.8 build150124
1920*1080
DS-2DF7284-A/D/AF
V5.2.8 build150124
1920*1080
iDS-2DF7284-A/D/AF
V5.2.8 build150124
1920*1080
DS-2DF7286-A/D/AF
V5.2.8 build150124
1920*1080
iDS-2DF7286-A/D/AF
V5.2.8 build150124
1920*1080
DS-2DF5284-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1920*1080
iDS-2DF5284-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1920*1080
DS-2DF5286-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1920*1080
iDS-2DF5286-A/D/A3/D3/AF/A3F
V5.2.8 build150124
1920*1080
DS_2DF7230I5-AW
V5.2.8 build150124
1920*1080
DS-2AF7220-A/D
V5.2.8 build150124
1920*1080
DS-2AF7230-A/D
V5.2.8 build150124
1920*1080
DS-2AF5220-A/D
V5.2.8 build150124
1920*1080
DS-2AF5230-A/D
V5.2.8 build150124
1920*1080
iDS-2DF5220S-D4/JY
V5.2.8 build150124
1920*1080
DS-2DF7268-A
V5.2.8 build150124
704*576
DS-2DF5268-A
V5.2.8 build150124
704*576
DS-2DF7264-A
V5.2.8 build150124
704*576
DS-2DF5264-A
V5.2.8 build150124
704*576
DS-2DE5172-A/A3
V5.2.10 build150128
1280*960
DS-2DE5174-A/AE/AE3/A3/D/D3
V5.2.10 build150128
1280*960
DS-2DE5176-A/AE
V5.2.10 build150128
1280*960
DS-2DE7172-A
V5.2.10 build150128
1280*960
DS-2DE7174-A/AE/D
V5.2.10 build150128
1280*960
DS-2DE7176-A/AE
V5.2.10 build150128
1280*960
DS-2DE7120i-A/AE
V5.2.10 build150128
1280*960
DS-2DM7130i-A
V5.2.10 build150128
1280*960
DS-2DM4120-A
V5.2.10 build150128
1280*960
DS-2DE5120I-A
V5.2.10 build150128
1280*960
DS-2DM5120-A
V5.2.10 build150128
1280*960
DS-2DM5130-A
V5.2.10 build150128
1280*960
DS-2DE2103-DE3/W
V5.2.10 build150128
1280*960
DS-2DE2103I-DE3/W
V5.2.10 build150128
1280*960
User Manual of Network Video Recorder
219
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
DS-2DE7184-A/AE/D
V5.2.10 build150128
1920*1080
DS-2DE5182-A/A3
V5.2.10 build150128
1920*1080
DS-2DE5184-A/AE/AE3/A3/D/D3
V5.2.10 build150128
1920*1080
DS-2DE5186-A/AE
V5.2.10 build150128
1920*1080
DS-2DE7182-A
V5.2.10 build150128
1920*1080
DS-2DE4582-A
V5.2.10 build150128
1920*1080
DS-2DE4220-A
V5.2.10 build150128
1920*1080
DS-2DE4182-A
V5.2.10 build150128
1920*1080
DS-2DM7230i-A
V5.2.10 build150128
1920*1080
DS-2DM7220i-A
V5.2.10 build150128
1920*1080
DS-2DE7186-A/AE
V5.2.10 build150128
1920*1080
DS-2DE5220I-A
V5.2.10 build150128
1920*1080
DS-2DM5220-A
V5.2.10 build150128
1920*1080
DS-2DM5230-A
V5.2.10 build150128
1920*1080
DS-2DE2202-DE3/W
V5.2.10 build150128
1920*1080
DS-2DE2202I-DE3/W
V5.2.10 build150128
1920*1080
DS-2DE4572-A
V5.2.10 build150128
1280*720
DS-2DE4172-A
V5.2.10 build150128
1280*720
DS-2DE7194-A/A3
V5.2.10 build150128
2048*1536
DS-2DE5194-A/A3
V5.2.10 build150128
2048*1536
DS-2DF1-518
V3.2.0 build131223
704*576
DS-2DM1-718
V3.2.0 build131223
704*576
DS-2DM1-518
V3.2.0 build131223
704*576
DS-2DF1-718
V3.2.0 build131223
704*576
DS-2DF1-514
V3.2.0 build131223
704*576
DS-2DF1-714
V3.2.0 build131223
704*576
DS-2DY9174-A
V5.2.8 build150124
1280*960
DS-2DY9176-A
V5.2.8 build150124
1280*960
DS-2DY9194-A
V5.2.8 build150124
2048*1536
DS-2DY9196-A
V5.2.8 build150124
2048*1536
DS-2DY9184-A
V5.2.8 build150124
1920*1080
DS-2DY9186-A
V5.2.8 build150124
1920*1080
DS-2DY9185-A
V5.2.8 build150124
1920*1080
DS-2DY9187-A
V5.2.8 build150124
1920*1080
DS-2DF8223IV-A
V5.3.0 build150304
1920*1080
DS-2DF8623IV-A
V5.3.0 build150304
3072*1728
DS-2DF6623V-A
V5.3.0 build150304
3072*1728
DS-2DF8823IV-A
V5.3.0 build150304
4096*2160
Network
Zoom
Camera
DS-2ZCN2006
V5.2.7 build141107
1280*960
DS-2ZCN2006(B)
V5.2.7 build141107
1280*960
DS-2ZCN3006
V5.2.7 build141107
1280*960
User Manual of Network Video Recorder
220
Type
Model
Version
Max.
Resolution
Sub-stream
Audio
Module
DS-2ZCN3006(B)
V5.2.7 build141107
1280*960
DS-2ZMN2006
V5.2.7 build141107
1280*960
DS-2ZMN2006(B)
V5.2.7 build141107
1280*960
DS-2ZMN3006
V5.2.7 build141107
1280*960
DS-2ZMN3006(B)
V5.2.7 build141107
1280*960
DS-2ZCN2007
V5.2.7 build141107
1920*1080
DS-2ZCN3007
V5.2.7 build141107
1920*1080
DS-2ZCN3007(B)
V5.2.7 build141107
1920*1080
DS-2ZMN2007
V5.2.7 build141107
1920*1080
DS-2ZMN3007
V5.2.7 build141107
1920*1080
DS-2ZMN3007(B)
V5.2.7 build141107
1920*1080
DS-2ZMN0407
V5.2.7 build141107
1920*1080
DS-2ZMN3207
V5.2.7 build141107
1920*1080
DS-2ZMN2008
V5.2.7 build141107
2048*1536
DS-2ZCN2008
V5.2.7 build141107
2048*1536
DS-2ZMN3007(S)
V5.2.2 build141113
1920*1080
DS-2ZCN3007(S)
V5.2.2 build141113
1920*1080
DS-2ZMN2307
V5.2.2 build141113
1920*1080
DS-2CN2307
V5.2.2 build141113
1920*1080
DS-2ZMN2309
V5.2.2 build141113
3072*2048
DS-2ZCN2309
V5.2.2 build141113
3072*2048
User Manual of Network Video Recorder
221
16.4.2 List of Third-party IP Cameras
ONVIF compatibility refers to the camera can be supported both when it uses the ONVIF protocol and its
private protocols. Only ONVIF is supported refers to the camera can only be supported when it uses the
ONVIF protocol. Only AXIS is supported refers to the function can only be supported when it uses the
AXIS protocol.
IP Camera
Manufacturer or
Protocol
Model
Version
Max.
Resolution
Sub-stream
Audio
ACTI
TCM4301-10D-X-00083
A1D-310-V4.12.09-AC
1280×1024
×
TCM5311-11D-X-00023
A1D-310-V4.12.09-AC
1280×960
×
TCM3401-09L-X-00227
A1D-220-V3.13.16-AC
1280×1024
×
×
ARECONT
AV8185DN
65172
1600×1200
×
×
AV1305M
65175
1280×1024
×
AV2155
65143
1600×1200
×
AV2815
65220
1920×1080
×
AV3105M
65175
1920×1080
×
AV5105
65175
1920×1080
×
AXIS
M1114
5.09.1
1024×640
×
M3011(ONVIF
compatibility)
5.21
704×576
√(Only AXIS is
supported)
×
M3014(ONVIF
compatibility)
5.21.1
1280×800
×
P3301(ONVIF
compatibility)
5.11.2
768×576
√(Only AXIS is
supported)
P3304(ONVIF
compatibility)
5.20
1440×900
√(Only AXIS is
supported)
P3343(ONVIF
compatibility)
5.20.1
800×600
√(Only AXIS is
supported)
P3344(ONVIF
compatibility)
5.20.1
1440×900
√(Only AXIS is
supported)
P5532
5.15
720×576
×
Q7404
5.02
720×576
Bosch
(ONVIF compatibility)
AutoDome Jr 800HD
39500450
1920×1080
×
NBC 265 P
07500453
1280×720
×
Dinion NBN-921-P
10500453
1280×720
×
Brickcom
FB-130Np (ONVIF
compatibility)
V3.1.0.8
1280×1024
×
CB-500Ap (ONVIF
V3.2.1.3
1920×1080
×
User Manual of Network Video Recorder
222
IP Camera
Manufacturer or
Protocol
Model
Version
Max.
Resolution
Sub-stream
Audio
compatibility)
WFB-100Ap
V3.1.0.9
1280×800
×
Canon
VB-M400
Ver.+1.0.0
1280×960
×
VB-M6000D
Ver.+1.0.0
1280×960
×
×
VB-M7000F
Ver.+1.0.0
1280×960
×
HUNT
HLC_79AD
V1.0.40
1600×1200
×
Panasonic
WV-SW152(ONVIF
compatibility)
Application:1.66
Image data:1.05
800×600
×
WV-SC386(ONVIF
compatibility)
Application:1.66
Image data:1.05
1280×960
WV-SW155(ONVIF
compatibility)
Application:1.66
Image data:1.05
1280×960
×
WV-SW316(ONVIF
compatibility)
Application:1.66
Image data:2.03
1280×960
WV-SP105(ONVIF
compatibility)
Application:1.66
Image data:1.03
1280×960
×
WV-SF132(ONVIF
compatibility)
Application:1.66
Image data:1.03
640×360
×
WV-SP102(ONVIF
compatibility)
Application:1.66
Image data:1.03
640×480
×
WV-SP509(ONVIF
compatibility)
Application:1.30
Image data:2.21
1280×960
WV-SW559(ONVIF
compatibility)
Application:1.30
Image data:2.21
1920×1080
WV-SW558(ONVIF
compatibility)
Application:1.30
Image data:2.21
1920×1080
×
WV-SW355(ONVIF
compatibility)
Application:1.66
Image data:1.04
1280×960
WV-SW352(ONVIF
compatibility)
Application:1.66
Image data:1.04
800×600
WV-SF342(ONVIF
compatibility)
Application:1.66
Image data:1.06
800×600
WV-SF332(ONVIF
compatibility)
Application:1.66
Image data:1.06
800×600
WV-SF346(ONVIF
compatibility)
Application:1.66
Image data:1.06
1280×960
WV-SP306H
Application:1.34
Image data:1.06
1280×960
WV-SP336H
Application:1.06
Image data:1.06
1280×960
PELCO
D5118
1.8.2-20120327-
2.9310-A1.7852
1280×960
×
IXE20DN-AAXVUU2
1.8.2-20120327-
2.9081-A1.7852
1920×1080
×
User Manual of Network Video Recorder
223
IP Camera
Manufacturer or
Protocol
Model
Version
Max.
Resolution
Sub-stream
Audio
IX30DN-ACFZHB3
1.8.2-20120327-
2.9080-A1.7852
2048×1536
×
SAMSUNG
(ONVIF compatibility)
SNB-5080P
V3.10_130416
1280×1024
√(Only ONVIF
is supported)
SANYO
VCC-HD2300P
2.03-02(110318-00)
1920×1080
×
×
VCC-HD2500P
2.02-02(110208-00)
1920×1080
×
VCC-HD4600P
2.03-02(110315-00)
1920×1080
×
SONY
SNC-CH220
1.50.00
1920×1080
×
×
SNC-RH124(ONVIF
compatibility)
1.73.00
1280×720
SNC-EP580(ONVIF
compatibility)
1.53.00
1920×1080
SNC-DH220T(Only
ONVIF is supported)
1.50.00
2048×1536
×
×
Vivotek
IP7133
0203a
640×480
×
×
FD8134(ONVIF
compatibility)
0107a
1280×800
×
×
IP8161(ONVIF
compatibility)
0104a
1600×1200
×
IP8331(ONVIF
compatibility)
0102a
640×480
×
×
IP8332(ONVIF
compatibility)
0105b
1280×800
×
×
ZAVIO
D5110
MG.1.6.03P8
1280×1024
×
F3106
M2.1.6.03P8
1280×1024
F3110
M2.1.6.01
1280×720
F3206
MG.1.6.02c045
1920×1080
F531E
LM.1.6.18P10
640×480
0303021050427
User Manual of Network Video Recorder
224
201

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hikvision DS-7616NI-E2-16N wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hikvision DS-7616NI-E2-16N

Hikvision DS-7616NI-E2-16N Bedienungsanleitung - Deutsch - 235 seiten

Hikvision DS-7616NI-E2-16N Bedienungsanleitung - Holländisch - 240 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info