Bedienungsanleitung Hikvision DS-7632NI-E2-8P (Seite 211 von 225) (Englisch)

662616

211

Zoom out

Zoom in

Vorherige Seite

1/225

Nächste Seite

User Manual of Network Video Recorder

210

c) The encoding standard is not supported with NVR.

Steps:

1. Verify the cable between the pickup and IP camera is connected well; impedance matches and

compatible.

the manufacturer of the IP camera.

2. Verify the setting parameters are correct.

Select “Menu > Record > Parameters > Record”, and set the Stream Type as “Audio & Video”.

3. Verify the audio encoding standard of the IP camera is supported by the NVR.

NVR supports G722.1 and G711 standards, and if the encoding parameter of the input audio is not one of

the previous two standards, you can log in the IP camera to configure it to the supported standard.

4. Check if the fault is solved by the above steps.

If it is solved, finish the process.

If not, please contact the engineer from our company to do the further process.



The image gets stuck when NVR is playing back by single or multi-channel.

Possible Reasons:

a) Poor network between NVR and IP camera, and there exists packet loss during the transmission.

b) The frame rate is not the real-time frame rate.

c) The NVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a

16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads to

a slight stuck.

Steps:

1. Verify the network between NVR and IP camera is connected.

1) When image is stuck, connect the RS-232 ports on PC and the rear panel of NVR with the RS-232

cable.

2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address

may change according to the real condition), and check if there exists packet loss.

Simultaneously press the Ctrl and C to exit the ping command.

2. Verify the frame rate is real-time frame rate.

Select “Menu > Record > Parameters > Record”, and set the Frame Rate to “Full Frame”.

3. Verify the hardware can afford the playback.

Reduce the channel number of playback.

Select “Menu > Record > Encoding > Record”, and set the resolution and bitrate to a lower level.

4. Reduce the number of local playback channel.

Select “Menu > Playback”, and uncheck the checkbox of unnecessary channels.

5. Check if the fault is solved by the above steps.

If it is solved, finish the process.

If not, please contact the engineer from our company to do the further process.



No record file found in the NVR local HDD, and prompt “No record file found”.

Possible Reasons:

a) The time setting of system is incorrect.

b) The search condition is incorrect.

c) The HDD is error or not detected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikvision DS-7632NI-E2-8P Seite 211

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hikvision DS-7632NI-E2-8P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info