Bedienungsanleitung Hikvision DS-8004HFI-ST (Seite 242 von 253) (Englisch)

629369

242

Zoom out

Zoom in

Vorherige Seite

1/253

Nächste Seite

User Manual of Digital Video Recorder

241

1) When image is stuck, connect the RS-232 ports on PC and the rear panel of device with the RS-232

cable.

2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address

may change according to the real condition), and check if there exists packet loss.

Simultaneously press Ctrl and C to exit the ping command.

2. Check the parameters of Main Stream (Continuous) and Main Stream (Event).

Select “Menu > Record > Parameters > Record”, and set the resolution of Main Stream (Event) the same

as the one of Main Stream (Continuous).

3. Verify the frame rate is real-time frame rate.

Select “Menu > Record > Parameters > Record”, and set the Frame rate to Full Frame.

4. Check if the fault is solved by the above steps.

If it is solved, finish the process.

If not, please contact the engineer from our company to do the further process.

 When using the device to get the live view audio, there is no sound or there is too much noise, or the

volume is too low.

Possible Reasons:

a) Cable between the pickup and camera is not connected well; impedance mismatches or incompatible.

b) The stream type is not set as “Video & Audio”.

c) The encoding standard is not supported with device.

Steps:

1. Verify the cable between the pickup and camera is connected well; impedance matches and compatible.

2. Verify the setting parameters are correct.

Select “Menu > Record > Parameters > Record”, and set the Stream Type as “Audio & Video”.

3. Verify the audio encoding standard of the camera is supported by the HDVR.

HDVR supports G722.1 and G711 standards, and if the encoding parameter of the input audio is not one

of the previous two standards, you can log in the IPC to configure it to the supported standard.

4. Check if the fault is solved by the above steps.

If it is solved, finish the process.

If not, please contact the engineer from our company to do the further process.

 The image gets stuck when HDVR is playing back by single or multi-channel IPC.

Possible Reasons:

a) Poor network between HDVR and IPC, and there exists packet loss during the transmission.

b)The frame rate is not the real-time frame rate.

c) The HDVR supports up to 16-channel synchronize playback at the resolution of 4CIF, if you want a

16-channel synchronize playback at the resolution of 720p, the frame extracting may occur, which leads to

a slight stuck.

Steps:

1. Verify the network between HDVR and IPC is connected.

1) When image is stuck, connect the RS-232 ports on PC and the rear panel of HDVR with the RS-232

cable.

2) Open the Super Terminal, and execute the command of “ping 192.168.0.0 –l 1472 –f” (the IP address

may change according to the real condition), and check if there exists packet loss.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hikvision DS-8004HFI-ST Seite 242

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hikvision DS-8004HFI-ST

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info