474121
14
Zoom out
Zoom in
Vorherige Seite
1/26
Nächste Seite
Main Source
: Move
OK : Select
Analog TV
Digital TV
VID/SVID1
VID/SVID2
Component1
Component2
PC
HDMI1
HDMI2
HDMI3
Power ON/OFF
ØTurning on: Connect the TV an AC power outlet and turn on the power switch located below the front right hand
side of unit. The power indicator will be initial red and then will change to blue. A few seconds later image will appear
on the screen.
ØTurning off to standby mode: Press the [ ]button on the front panel or on the remote control to switch standby
mode. You can activate the unit again by pressing the [ ] button.
ØPower indicator:
Red indicates standby mode.
Blue shows that the unit is on.
There will no light when the power switch is in off position.
Notes:
Turn the power switch off when you do not intend to use the TV for long periods, for example overnight. Remove the
connection from the wall power outlet if you do not intend to use the unit for longer periods, for example if you plan to
be away a few days.
Wait at least 5 seconds after turning off if you want to re-start the TV.
Signal source selection
[SOURCE] button: Press the [SOURCE] button and press [P+/P-] button to select signal input, press [OK] to confirm
selection.
[HDMI] button: press [HDMI] button to select HDMI signal input.
[YPBPR] button: press [YPBPR] button to select Component signal input.
[D/A] button: press [D/A] button to switch Digital/Analog signal input.
Select channels
You can select channels by press [P+/-] on the remote or press [CH / ] on the front panel
of TV.
Select channels by numbers
Input channel numbers sequentially to select channels by program numbers.
For example, to select channel 120, press the button 1, and 1will be displayed on the top right corner of the screen,
then press the button 2, 12 will be displayed, press the button 0, channel 120 will now appear on screen.
[VOL ] or [VOL ]
Adjust Volume
Press on the front panel of TV or press [v-/v+] on the remote to adjust volume.
Use [LAST] button
Press [ LAST ] button repeatedly to alternate between the present program and the previous in both the
same and different signals source.
program
14
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hisense HSLC8129HDI wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info