Bedienungsanleitung Hisense pdp4220 (Seite 24 von 25) (Englisch)

140786

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

Appendix

PDP Wall-mounting Bracket Installation Guide

READ CAREFULLY BEFORE INSTALLATION!

THE INSTALLATION GUIDE SHOULD BE RETAINED FOR FUTURE REFERENCE.

Caution:

1. Do NOT attempt to install the TV by yourself to avoid mistakes or hazard. Refer all

installation to qualified servicing personnel.

2. Do NOT install the TV on a wall aslope or a wall that makes the TV screen sloping

over 25o off plumb line. Otherwise, it may cause tumble or injury.

3. Refer all installation to qualified servicing personnel.

4. One must follow the instructions in this guide to correctly install the TV.

5. It requires more than one person to install the TV.

6. Before installation, examine whether the wall conforms to the specifications and

whether the supplied parts can be fixed on it. The wall for mounting should sustain

the weight of TV and speakers, e.g. cement wall or brick wall. Do NOT attempt to

install the TV on a flexible wall such as sand wall or plaster wall, unless the bolt are

fixed on an area with standard building rigidity which sustains the weight of the TV

and speakers. If the rigidity of the wall can not be measured, every mounting hole

should sustain a frontal force of over 100N and a shearing force of over 200N.

7. Use the specified electric drill and drill bit for drilling. The drilling holes should

conform to the specifications.

8. To avoid fire and shock, do NOT place radiator, heater or humidifier below the

installed TV.

9. The TV should be kept away from moisture, sensors and power line. The TV should

be kept away from impact and vibration.

10. Ensure that the power supply be disconnected before installation for fear of fire

and shock.

Wall-mounting Installation Steps:

1. Take out the brackets from the package, and check if there are serious defects

(e.g. infirm juncture).

2. Adjust the bracket to the desired angle. Use the bolts 2 to adjust the angle by

meeting holes of column beam 8 and holes of lever 5

3. Drill locating holes in the specified dimension in a vertical wall of concrete or brick.

The hole size should be 11mm. The hole depth should accommodate the

expanding tube of the bolt.

4. Fix the bolts into the drilled holes in step3, and then cover each bolt with a metal

washer. Meet the four mounting holes in the bracket with the four bolts in the wall,

cover each bolt with a metal washer, and then fasten with a screw nut. Check its

rigidity by pulling the bracket.

5. Fix the fixture disk 4 to the back cover of the TV using four bolt 3(M8X45).

6. Wall-mount the TV by putting the four fixture disks into the four mounting holes A.

7. If the customer is not satisfied with the mounting angle, take down the TV and

adjust the angle before re-mounting.

After wall-mounting the TV, use bolts 2 to fix the fixture disks for fear of accidental

slide.

-21 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hisense pdp4220 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info