Bedienungsanleitung Hitachi 43HGW69 (Seite 18 von 26) (Englisch)

646611

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English - 14 -

the option Delete Rec. Timer. The recording will be

cancelled.

Set Timer on Event / Delete Timer on Event: After

you have selected a programme in the EPG menu,

press the OK button. Select Set Timer on Event

option and press the OK button. You can set a timer

for future programmes. To cancel an already set timer,

highlight that programme and press the OK button.

Then select Delete Timer on Event option. The timer

will be cancelled.

Notes: You cannot switch to any other channel while

there is an active recording or timer on the current

channel.

It is not possible to set timer or record timer for two

or more individual events at the same time interval.

Software Upgrade

Your TV is capable of nding and updating the rmware

automatically via the broadcast signal or via Internet.

Software upgrade search via user interface

On the main menu select System>Settings and then

More. Navigate to Software upgrade and press the

OK button. In Upgrade options menu select Scan

for upgrade and press OK button to check for a new

software upgrade.

If a new upgrade is found, it starts to download the

upgrade. After the download is completed conrm the

question asking about rebooting the TV by pressing

the OK to continue with the reboot operation.

3 AM search and upgrade mode

Your TV will search for new upgrades at 3:00 o’clock if

Automatic scanning option in the Upgrade options

menu is set to Enabled and if the TV is connected

to an aerial signal or to Internet. If a new software is

found and downloaded successfully, it will be installed

at the next power on.

Note: Do not unplug the power cord while led is blinking

during the reboot process. If the TV fails to come on after the

upgrade, unplug, wait for two minutes then plug it back in.

Troubleshooting & Tips

Tv will not turn on

Make sure the power cord is plugged in securely to

wall outlet. Check if batteries are exhausted. Press

the Power button on the TV.

Poor picture

• Check if you have selected the correct TV system.

• Low signal level can cause picture distortion. Please

check antenna access.

• Check if you have entered the correct channel

frequency if you have done manual tuning.

• The picture quality may degrade when two devices

are connected to the TV at the same time. In such

a case, disconnect one of the devices.

No picture

• This means your TV is not receiving any transmission.

Make sure the correct source has been selected.

• Is the antenna connected properly?

• Is the antenna cable damaged?

• Are suitable plugs used to connect the antenna?

• If you are in doubt, consult your dealer.

No sound

• Check if the TV is muted. Press the Mute button or

increase the volume to check.

• Sound may be coming from only one speaker. Check

the balance settings from sound menu.

Remote control - no operation

• The batteries may be exhausted. Replace the

batteries.

Input sources - can not be selected

• If you cannot select an input source, it is possible

that no device is connected. If not;

• Check the AV cables and connections if you have

tried to connect a device.

Recording unavailable

To record a programme, you should rst connect a

USB disk to your TV while the TV is switched off.

You should then switch on the TV to enable recording

feature. If you cannot record, try switching off the TV

and then re-inserting the USB device.

USB is too slow

If a “USB disk writing speed too slow to record”

message is displayed on the screen while starting a

recording, try restarting the recording. If you still get

the same error, it is possible that your USB disk does

not meet the speed requirements. Try connecting

another USB disk.

Connectivity Functions (depending on the model)

Tocongurewired/wirelesssettingspleaserefer

to the Network/Internet Settings section in the

Settings Menu.

Connecting TV to a Home Network

Connectivity feature allows the TV to connect to the

home network wired or wirelessly. You can use this

networking system to connect to the Internet Portal

or to access photo, video and audio les that are

stored on a media server connected to the network

and play/display them on the TV.

Wired connection

Connect the TV to the modem/router via a LAN

cable (not supplied). Select Network Type as Wired

Device in Network/Internet Settings menu.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi 43HGW69 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi 43HGW69

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info