Bedienungsanleitung Hitachi 49HGW69 (Seite 13 von 26) (Englisch)

646612

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English - 9 -

Environmental Information

This television is designed to be environment friendly.

To reduce energy consumption, you can follow these

steps:

If you set the Energy Saving to Minimum, Medium,

Maximum or Auto the TV will reduce the energy

consumption accordingly. If you like to set the

Backlight to a xed value set as Custom and adjust

the Backlight (located under the Energy Saving

setting) manually using Left or Right buttons on the

remote. Set as Off to turn this setting off.

Note: Available Energy Saving options may differ

depending on the selected Mode in the Picture menu.

The Energy Saving settings can be found in the

Picture menu. Note that some picture settings will

be unavailable to be changed.

If pressed Right button while Auto option is selected or

Left button while Custom option is selected, “Screen

will be off in 15 seconds.” message will be displayed

on the screen. Select Proceed and press OK to turn

the screen off immediately. If you don’t press any

button, the screen will be off in 15 seconds. Press

any button on the remote or on the TV to turn the

screen on again.

Note: Screen Off option is not available if the Mode

is set to Game.

When the TV is not in use, please switch off or

disconnect the TV from the mains plug. This will also

reduce energy consumption.

Switching On/Off (depending on the model)

To Switch the TV On

• Connect the power cord to the 220-240V AC, 50 Hz.

• Then the standby LED lights up.

To switch on the TV from standby mode either:

• Press the Standby button, Programme +/- or a

numeric button on the remote control.

Control buttons on the TV (depending on model)

• Press the Standby button or Programme +/- button

on the TV. The TV will then switch on.

-or-

• Press and hold the middle of the control switch on

the left side of the TV until the TV comes on from

standby. The TV will then switch on.

To Switch the TV Off (depending on model)

• Press the Standby button on the remote control or

press the Standby button on the TV or press and

hold the control switch on the TV until shut down,

so the TV switches into standby mode (depends on

the model).

• To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched into standby mode,

standby LED can blink to indicate that features such as

Standby Search, Over Air Download or Timer is active.

The LED can also blink when you switch on the TV from

standby mode.

First Time Installation (depending on the model)

When turned on for the first time, the language

selection screen is displayed. Select the desired

language and press OK.

On the next screen, set your preferences using the

directional buttons.

Note: Depending on the Country selection you may be asked

to set and conrm a PIN at this point. The selected PIN cannot

be 0000. You have to enter it if you are asked to enter a PIN

for any menu operation later.

About Selecting Broadcast Type

Digital Aerial: If Aerial broadcast search option is

turned on, the TV will search for digital terrestrial

broadcasts after other initial settings are completed.

Digital Cable (depending on model): If Cable

broadcast search option is turned on, the TV will

search for digital cable broadcasts after other

initial settings are completed. According to your

other preferences a conrmation message may be

displayed before starting to search. Select YES and

press OK to proceed. To cancel operation, select NO

and press OK. You can select Network or set values

such as Frequency, Network ID and Search Step.

When nished, press OK button.

Note: Searching duration will change depending on

the selected Search Step.

Satellite (depending on model): If Satellite

broadcast search option is turned on, the TV will

search for digital satellite broadcasts after other initial

settings are completed. Before satellite search is

performed some settings should be made. Antenna

Type menu will be displayed rst. You can select

Antenna Type as Direct, Single Satellite Cable or

DiSEqC switch by using “ ” or “ ” buttons.

•Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

•Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Congure

settings by following instructions on the next screen.

Press OK to scan for services.

•DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type.

Press OK to continue. You can set four DiSEqC

options (if available) on the next screen. Press OK

button to scan the rst satellite in the list.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi 49HGW69 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi 49HGW69

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info