Bedienungsanleitung Hitachi 55HGW69 (Seite 3 von 26) (Englisch)

646615

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Auto Setup procedure (depending on the model)

PLEASE ENSURE BOTH UNITS ARE SWITCHED OFF

BEFORE CONNECTING. Use a HDMI to HDMI cable to

connect the two units together. To select the HDMI input,

press the Source button on the remote control. Each time it is

pressed the on-screen menu confirms your selection.

* The appearance of the Source button may differ depending on the

model of the remote control

HDMI input

SOURCESOURCE

To HDMI connection

on the device

When the TV is operated for the first time, installation wizard will guide you through the process.

First, language selection screen will be displayed. Select the desired language and press OK.

On the following screens, set your preferences using the directional buttons.

About Selecting Broadcast Type

Digital Aerial: If this broadcast search option is turned on, the TV will search for digital terrestrial

broadcasts after other initial settings are completed.

Digital Cable: If this broadcast search option is turned on, the TV will search for digital cable

broadcasts after other initial settings are completed. According to your other preferences a

confirmation message may be displayed before starting to search. Select Yes and press OK to

proceed. To cancel operation, select No and press OK. You can select Network or set values such

as Frequency, Network ID and Search Step. When finished, press OK button.

Note: Searching duration will change depending on the selected Search Step.

Satellite: If Satellite broadcast search option is turned on, the TV will search for digital satellite

broadcasts after other initial settings are completed. Before satellite search is performed some

settings should be made. Antenna Type menu will be displayed first. You can select Antenna Type

as Direct, Single Satellite Cable or DiSEqC switch by using directional buttons.

Analogue: If Analogue broadcast search option is turned on, the TV will search for analogue

broadcasts after other initial settings are completed.

Additionally you can set a broadcast type as your favourite one. Priority will be given to the selected

broadcast type during the search process and the channels of it will be listed on the top of the

channel list. When finished, press OK to continue.

You can activate Store Mode option at this point. This option is intended only for store use. It is

recommended to select Home Mode for home use.

Press OK button on the remote control to continue and the Network/Internet Settings menu will be

displayed. Please refer to the next section about internet connection on the next page to configure a

wired or a wireless connection. After the settings are completed press OK button to continue.

After the initial settings are completed TV will start to search for available broadcasts of the selected

broadcast types.

After all the available stations are stored, scan results will be displayed. Press OK to continue. The

Edit Channel List menu will be displayed next. You can edit the channel list according to your

preferences or press the Menu button to quit and watch TV.

Note: Do not turn off the TV while initializing first time installation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi 55HGW69 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi 55HGW69

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info