Bedienungsanleitung Hitachi C 13 U (Seite 7 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

110238

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

English

SAFETY INSTRUCTIONS FOR ALL SAWS

a) DANGER: Keep hands away from cutting area and

the blade. Keep your second hand on auxiliary handle,

or motor housing.

If both hands are holding the saw, they cannot be

cut by the blade.

b) Do not reach underneath the workpiece.

The guard cannot protect you from the blade below

the workpiece.

c) Adjust the cutting depth to the thickness of the

workpiece.

Less than a full tooth of the blade teeth should be

visible below the workpiece.

d) Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform.

It is important to support the work properly to

minimize body exposure, blade binding, or loss of

control.

e) Hold power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord.

Contact with a “live” wire will also make exposed

metal parts of the power tool “live” and shock the

operator.

f) When ripping always use a rip fence or straight edge

guide.

This improves the accuracy of cut and reduces the

chance of blade binding.

g) Always use blades with correct size and shape

(diamond versus round) of arbour holes.

Blades that do not match the mounting hardware

of the saw will run eccentrically, causing loss of

control.

h) Never use damaged or incorrect blade washers or

bolt.

The blade washers and bolt were specially designed

for your saw, for optimum performance and safety

of operation.

FURTHER SAFETY INSTRUCTIONS FOR ALL

SAWS

Causes and operator prevention of kickback:

– kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the

operator;

– when the blade is pinched or bound tightly by the

kerf closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the

operator;

– if the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can

dig into the top surface of the wood causing the

blade to climb out of the kerf and jump back toward

the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below.

a) Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces.

Position your body either side of the blade, but not

in line with the blade.

Kickback could cause the saw to jump backwards,

but kickback forces can be controlled by the operator,

if proper precautions are taken.

b) When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop.

Never attempt to remove the saw from the work or

pull the saw backward while the blade is in motion

or kickback may occur.

Investigate and take corrective actions to eliminate

the cause of blade binding.

c) When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are

not engaged into the material.

If saw blade is binding, it may walk up or kickback

from the workpiece as the saw is restarted.

d) Support large panels to minimize the risk of blade

pinching and kickback.

Large panels tend to sag under their own weight.

Supports must be placed under the panel on both

sides, near the line of cut and near the edge of the

panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade binding

and kickback.

f) Blade depth and bevel adjusting locking levers must

be tight and secure before making cut.

If blade adjustment shifts while cutting, it may

cause binding and kickback.

g) Use extra caution when making a “plunge cut” into

existing walls or other blind areas.

The protruding blade may cut objects that can cause

kickback.

SAFETY INSTRUCTIONS FOR SAWS WITH

PENDULUM GUARD OR TOW GUARD

a) Check lower guard for proper closing before each use.

Do not operate the saw if lower guard does not move

freely and close instantly. Never clamp or tie

the lower guard into the open position.

If saw is accidentally dropped, lower guard may be

bent.

Raise the lower guard with the retracting handle

and make sure it moves freely and does not touch

the blade or any other part, in all angles and depth

of cut.

b) Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use.

Lower guard may operate sluggishly due to damaged

parts, gummy deposits, or build-up of debris.

c) Lower guard may be retracted manually only for

special cuts such as “plunge cuts“ and “compound

cuts“. Raise lower guard by retracting handle and as

soon as blade enters the material, the lower guard

must be released.

For all other sawing, the lower guard should operate

automatically.

d) Always observe that the lower guard is covering the

blade before placing saw down on bench or floor.

An unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to stop

after switch is released.

01Eng_C13U_WE 08/10/31, 10:146

Hitachi C 13 U Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info