Bedienungsanleitung Hitachi c 18 dsl (Seite 12 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

383804

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

NEVER place your hand or fingers behind the saw

(Fig. 3). If kickback occurs, the saw could easily

jump backwards over your hand, possibly causing

severe injury.

30. WARNING: It is important to support the work

piece properly and to hold the saw firmly to

prevent loss of control which could cause personal

injury. Fig. 4 illustrates typical hand support of the

saw.

31. Place the wider portion of the saw base on that

part of the work piece which is solidly supported,

not on the section that will fall off when the cut

is made. As examples, Fig. 5 illustrates the RIGHT

way to cut off the end of board, and Fig. 6 the

WRONG way. If the work piece is short or small,

clamp is down.

DON’T TRY TO HOLD SHORT PLACES BY HAND!

32. Never attempt to saw with the circular saw held

upside down in a vise. This is extremely dangerous

and can lead to serious accidents (Fig. 7).

33. When the brake becomes ineffective, replace the

carbon brushes with new ones.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 to 3 described below, when using

this product, even if you are pulling the switch, the

motor may stop. This is not the trouble but the result

of protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

3. If the battery is overheated under overload work,

the battery power may stop.

In this case, stop using the battery and let the

battery cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

⅜ During work make sure that swarf and dust do

not fall on the battery.

⅜ Make sure that any swarf and dust falling on the

power tool during work do not collect on the battery.

⅜ Do not store an unused battery in a location

exposed to swarf and dust.

⅜ Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such

as a nail, strike with a hammer, step on, throw

or subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

7. If the battery charging fails to complete even

when a specified recharging time has elapsed,

immediately stop further recharging.

8. Do not put or subject the battery to high

temperatures or high pressure such as into a

microwave oven, dryer, or high pressure container.

9. Keep away from fire immediately when leakage

or foul odor are detected.

10. Do not use in a location where strong static

electricity generates.

11. If there is battery leakage, foul odor, heat

generated, discolored or deformed, or in any way

appears abnormal during use, recharging or

storage, immediately remove it from the equipment

or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your

eyes, do not rub your eyes and wash them well

with fresh clean water such as tap water and

contact a doctor immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well

with clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you find rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the first time, do not use and return

it to your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of fire. Please observe the

following matters when storing the battery.

⅜ Do not place electrically conductive cuttings, nails,

steel wire, copper wire or other wire in the storage

case.

⅜ Either install the battery in the power tool or

store by securely pressing into the battery cover

until the ventilation holes are concealed to prevent

short-circuits (See Fig. 8).

SPECIFICATIONS

Power Tool

Model C18DSL

No-load speed 3400 min

–1

Capacity Cutting depth 90° 57 mm

45° 40 mm

Rechargeable battery BSL1830: Li-ion 18 V (3.0 Ah, 10 cells)

Light bulb 12 V, 5 W

Weight 3.2 kg

01Eng_C18DSL_WE 8/8/08, 10:1211

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi c 18 dsl Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info