Bedienungsanleitung Hitachi c 18 dsl (Seite 15 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

383804

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a

while.

CAUTION

⅜ When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes rest

until the next charging.

⅜ If the battery is recharged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

map light in green.

The battery will not be recharged. In such a case,

let the battery cool before charging.

⅜ When the pilot lamp flickers in red (at 0.2-second

intervals), check for and take out any foreign objects

in the charger’s battery installation hole. If there are

no foreign objects, it is probable that the battery

or charger is malfunctioning. Take it to your

authorized Service Center.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by

following the precautions.

2. Prepare a wooden workbench (Fig. 12)

Since the saw blade will extend beyond the lower

surface of the lumber, place the lumber on a

workbench when cutting. If a square block is utilized

as a workbench, select level ground to ensure it

is properly stabilized. An unstable workbench will

result in hazardous operation.

CAUTION

To avoid possible accident, always ensure that the

portion of lumber remaining after cutting is securely

anchored or held in position.

ADJUSTING THE SAW PRIOR TO USE

CAUTION

Pull out battery before doing any adjusting.

1. Adjusting the cutting depth

As shown in Fig. 13, hold the handle with one hand

while loosening the wing nut with the other.

The cutting depth can be adjusted by moving the

base to the desired position. In such manner adjust

the cutting depth and then securely retighten the

wing nut.

2. Adjusting the angle of inclination

As shown in Fig. 14 by loosening the wing bolt on

the incline gauge, the saw blade may be inclined

to a maximum angle of 50° in relation to the base.

After having completed the adjustment, reconfirm

that the wing bolt are firmly tightened.

NOTE

Values of the inclined gauge provided on the base

merely serve as a rough guideline. For cutting

operation at an inclined posture, use the circular

saw after adjusting the angle between the base and

the saw blade with a protractor, etc.

3. Regulating the guide (Fig. 16)

The cutting position can be regulated by moving

the guide to the left or right after loosening its knob

bolt. The guide may be mounted on either the right

or left side of the tool.

HOW TO USE

1. Operation of switch (Fig. 17)

(switch trigger and light switch)

(1) For safe operation of the machine, a “switch lock”

is provided on the side of a handle.

If the “switch trigger” is pulled in a state where

“switch lock” is pressed in the direction of the

arrow mark, the main switch can be turned ON.

And the “switch lock” is used as the “light switch”.

If the “switch lock (light switch)” is pressed in a

state, the light is turned ON.

(2) After the switch is turned ON, even when you

release your hand from the switch lock, the body

continues running and the light continues being

turned ON as long as you keep on pulling the

switch trigger.

(3) If you release the switch trigger, you can turn OFF

the switch and the “switch lock” returns to the

original position automatically and the light turns

OFF too.

CAUTION

⅜ Do not fix and secure the switch lock. Besides, keep

your finger off the switch trigger when the circular

saw is being carried around. Otherwise, the main

body switch can be inadvertently turned ON,

resulting in unexpected accidents.

⅜ Keep the light ON during cutting operation only.

If it is lit ON in other cases, the main body switch

can be inadvertently turned ON, resulting in

unexpected accidents.

⅜ If the main body is left as it is with the battery

inserted, there can be a case where the [switch lock]

touches the floor and/or wall surface and lights up

continuously, depending on the direction of the

body. Be careful, since continuous lighting can easily

make a full-charged battery go dead in about 3

hours.

2. About Remaining Battery Indicator

When pressing the remaining battery indicator

switch, the remaining battery indicator lamp lights

and the battery remaining power can be checked.

(Fig. 18) When releasing your finger from the

remaining battery indicator switch, the remaining

battery indicator lamp goes off. The Table 4 shows

the state of remaining battery indicator lamp and

the battery remaining power.

01Eng_C18DSL_WE 8/8/08, 10:1214

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi c 18 dsl Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info