Bedienungsanleitung Hitachi C10FSH (Seite 14 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

505940

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

English

STANDARD ACCESSORIES

(1) 255 mm TCT Saw blade (mounted on tool) ............. 1

(2) Dust bag ...................................................................... 1

(3) 10 mm Box wrench .................................................... 1

(4) Vise Assembly ............................................................ 1

(5) Holder .......................................................................... 1

(6) Sub Fence (A) ............................................................. 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (SOLD SEPARATELY)

(1) Extension Holder and Stopper

(2) Saw blade 255 mm TCT Saw blade (Total teeth: 72)

(3) Crown molding Vise Ass'y (Include Crown molding

Stopper (L))

(4) Crown molding Stopper (L)

(5) Crown molding Stopper (R)

Optional accessories are subject to change without notice.

APPLICATION

⅜ Cutting various types of aluminium sash and wood.

UNPACKING

⅜ Carefully unpack the power tool and all related items

(standard accessories).

⅜ Check carefully to make certain all related items

(standard accessories) are present.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the trigger

switch is in the ON position, the power tool will start

operating immediately, inviting serious accident.

3. Extention cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be kept

as short as practicable.

4. When the power tool is prepared for shipping, its

main parts are secured by a locking pin

Move the handle slightly so that the locking pin can

be disengaged.

During transport, lock the locking pin into the gear

case (Fig. 4).

5. Attach the dust bag to the main unit (Fig. 1)

6. Installation

Ensure that the machine is always fixed to bench.

Attach the power tool to a level, horizontal work bench.

Select 8 mm diameter bolts suitable in length for the

thickness of the work bench.

Bolt length should be at least 25 mm plus the thickness

of the work bench.

For example, use 8 mm × 65 mm bolts for a 25 mm

thick work bench.

ADJUSTING THE POWER TOOL PRIOR TO USE

CAUTION

Make all necessary adjustments before inserting the

plug in the power source.

1. Check to see that the lower guard operates smoothly

CAUTION

⅜ This slide compound miter saw is equipped with a

saw head lock as safety device.

⅜ To lower the saw head to cut, the lock must be released

by pressing the lever (A) with your thumb.

(1) When you push down the handle while pushing the

lever (A), check that the lower guard revolves

smoothly (Fig. 5).

(2) Next, check that the lower guard returns to the original

position when the handle is raised.

2. Checking the saw blade lower limit position (Fig. 7)

Check that the saw blade can be lowered 10 mm to

11 mm below the table insert.

If necessary, adjust as follows:

(1) Loosen the 8 mm wing nut.

(2) Insert your 6 mm hexagon bar wrench from behind

of the tool and turn the 8 mm hexagon socket set

screw to the left (counterclockwise) viewed from

behind of the tool.

(3) Turn the 8 mm depth adjustment bolt, change the

height where the bolt head and the gear case contacts,

and adjust the lower limit position of the saw blade.

One turn of the 8 mm depth adjustment bolt changes

the lower limit position of the saw blade by about 8

mm, and this information can be used as a rough

guide.

(4) Turn the 8 mm hexagon socket set screw to the right

(clockwise) as viewed from behind of the tool, and let

it softly contact the tip of the 8 mm depth adjustment

bolt.

CAUTION

Adjust the lower limit position so that the saw blade

will not cut the turntable or complete cutting cannot

be done.

PRACTICAL APPLICATIONS

CAUTION

⅜ It is dangerous to remove or install the workpiece

while the saw blade is turning.

⅜ When sawing, clean off the shavings from the

turntable.

⅜ If the shavings accumulate too much, the saw blade

from the cutting material will be exposed. Never

subject your hand or anything else to go near the

exposed blade.

1. Tightly secure the material by vise assembly to be

cut so that it does not move during cutting

2. Switch operation

Pulling the trigger turns the switch on. Releasing the

trigger turns the switch off.

3. Base holder adjustment (Fig. 3)

Loosen the 6 mm bolt with the supplied 10 mm box

wrench. Adjust the base holder until its bottom surface

contacts the bench or the floor surface.

4. Cutting a groove on the guard

Holder (A) has a guard (see Fig. 6) into which a groove

must be cut. Loosen the 6 mm knob bolt to retract the

guard slightly.

01Eng_C10FSH_WE 5/31/10, 7:07 PM13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi C10FSH Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info