Bedienungsanleitung Hitachi C18DBL (Seite 8 von 210) (Alle Sprachen)

661466

Zoom out

Zoom in

Vorherige Seite

1/210

Nächste Seite

English

Inclined cutting (+45° direction) 22 202

Dismounting the saw blade 23 203

Mounting the saw blade 24 203

Selecting accessories ― 204

(*1) About the mode select function

Each time the mode selector switch is pushed, the

operation mode changes.

When Silent mode is selected, the Silent mode indicator

lamp lights up.

Silent mode reduces maximum motor RPM enabling

eﬃ cient work with less noise.

If the load increases while the motor is operating in

Silent mode, it automatically changes to Power mode.

Additionally, if the load decreases again, it automatically

returns to Silent mode.

In Power mode, no change is made to Silent mode even

when the load decreases.

Mode No-load speed

Power 5000 min

-1

Silent 3000 min

-1

NOTE

○ The mode will only change after a battery is installed and

the switch is pulled once.

○ The current mode will be maintained even if the switch is

on/oﬀ , or the battery is removed/reinserted.

MAINTENANCE AND INSPECTION

1. Inspecting the saw blade

Since use of as dull saw blade will degrade eﬃ ciency

and cause possible motor malfunction, sharpen or

replace the saw blade as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Maintenance of lower guard

For safe and proper working, always keep the machine

and ventilation slots clean. The lower guard must

always be able to more freely and retract automatically.

Therefore, always keep the area around the lower guard

clean. Remove dust and chips by blowing out with

compressed air or with a brush.

5. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

6. Storage

Storing in a place below 40°C and out of the reach of

children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 90 dB (A)

Measured A-weighted sound pressure level: 79 dB (A)

Uncertainty K: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Cutting chipboard:

Vibration emission value a

= 1.9 m/s

Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diﬀ er from the declared total value depending in

the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

NOTE

Due to HITACHI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

0000Book_C18DBL.indb 80000Book_C18DBL.indb 8 2017/02/03 14:43:182017/02/03 14:43:18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi C18DBL Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info