Bedienungsanleitung Hitachi C7ST (Seite 9 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

506016

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

English

PRECAUTIONS ON USING CIRCULAR SAW

1. Do not use saw blades which are deformed or

cracked.

2. Do not use saw blades made of high speed steel.

3. Do not use saw blades which do not comply with

the characteristics specified in these instructions.

4. Do not stop the saw blades by lateral pressure

on the disc.

5. Always keep the saw blades sharp.

6. Ensure that the lower guard moves smoothly and

freely.

7. Never use the circular saw with its lower guard

fixed in the open position.

8. Ensure that the retraction mechanism of the guard

system operates correctly.

9. Never operate the circular saw with the saw blade

turned upward or to the side.

10. Ensure that the material is free of foreign matters

such as nails.

11. For model C7ST, the saw blades range should be

from 185 mm to 180 mm.

12. Disconnect the plug from the receptacle before

carrying out any adjustment, servicing or

maintenance.

13. Do not use abrasive wheels.

STANDARD ACCESSORIES

(1) Saw Blade (Dia. 185 mm) (mounted on tool ) ..... 1

(2) Box Wrench ............................................................... 1

(3) Guide .......................................................................... 1

(4) Wing-bolt ................................................................... 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (sold separately)

(1) Dust Collector Set

Connect the suction hose to collect saw dust with

the vacuum cleaner (see Fig. 12).

(2) Washer (A)

............... for 16 mm (Hole dia. of saw blade)

............... for 20 mm (Hole dia. of saw blade)

............... for 30 mm (Hole dia. of saw blade)

Optional accessories are subject to change without notice.

APPLICATION

Cutting various types of wood.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized con-

forms to the power requirements specified on the

product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Prepare a wooden workbench (Fig. 1)

Since the saw blade will extend beyond the lower

surface of the lumber, place the lumber on a

workbench when cutting. If a square block is utilized

as a workbench, select level ground to ensure it

is properly stabilized. An unstable workbench will

result in hazardous operation.

CAUTION

To avoid possible accident, always ensure that the

portion of lumber remaining after cutting is se-

curely anchored or held in position.

5. RCD

The use of a residual current device with a rated

residual current of 30mA or less at all times is

recommended.

ADJUSTING THE POWER TOOL PRIOR TO USE

1. Adjusting the cutting depth

To adjust cutting depth, loosen the lever (A) and,

while holding the base with one hand, move the

main body up and down to obtain the prescribed

cutting depth. After adjusting to the prescribed cutting

depth, tighten the lever (A) securely (Fig. 2).

CAUTION

Should this lever (A) remain loosened, it will create a

very hazardous situation. Always thoroughly clamp it.

2. Adjusting the angle of inclination

By loosening the lever (A) at the scale, the saw

blade can be inclined up to maximum angle of 45°

against the base.

The angle of inclination can also be regulated by

loosening the lever (A) at the scale (Fig. 3).

Voltage (by areas)* (110 V, 230 V)

Cutting Depth

90° 62 mm

45° 47.5 mm

Power Input* 1560 W / 1710 W

No-Load Speed 6000 min

–1

Weight (without cord) 4.3 kg

* Be sure to check the nameplate on product as it is subject to change by areas.

SPECIFICATIONS

01Eng_C7ST_WE 4/15/11, 13:388

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi C7ST Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info