Bedienungsanleitung Hitachi CF18DSL (Seite 4 von 220) (Alle Sprachen)

616692

Zoom out

Zoom in

Vorherige Seite

1/220

Nächste Seite

English

Cutter block deformation

10. Prior to use, conduct a trial run. If during the trial run or

while using the tool, there are any indications of trouble,

abnormal sounds or abnormal vibrations, immediately

switch o the tool , discontinue use and arrange for

inspection or repairs with a Hitachi Authorized Service

Center. Continued use may result in injury.

11. If you accidentally drop or bump the tool, check it for

damage, cracks or deformities. If there are any, they may

result in injury.

CAUTION

1. Before operation, inspect the cutter block and housing

for loose bolts, hydraulic oil volume etc. Also, make sure

to remove any attached tools such as a wrench.

2. Make sure to remove the battery when inspecting,

cleaning or exchanging the cutter block. Accidentally

switching the tool on may result in injury.

3. Make sure there is nobody below when working in high

locations. Dropping the tool or other materials could

result in accident or injury.

4. Only use genuine hydraulic oil. The genuine oil must

be the equivalent of international ISO auxiliary viscosity

grade 46 (VG46).

5. If hydraulic oil comes into contact with eyes, do not rub.

Wash immediately and thoroughly with clean running

water and contact a physician for treatment. Left

untreated, the oil may lead to eye damage.

6. If hydraulic oil comes into contact with skin, wash

immediately and thoroughly with clean water and soap.

Failure to do so may lead to skin inﬂ ammation.

7. If hydraulic oil is accidentally swallowed, do not attempt

to vomit. Immediately contact a physician for treatment.

8. When hydraulic oil is not in use, make sure the lid of the

container is secure and store it in a dark place away from

direct sunlight and out of the reach of children.

9. Do not place the hydraulic oil container near a

combustion source such as heat, ﬂ ame or sparks. Doing

so may result in explosion.

10. Make sure the battery is securely attached. If not

securely attached, the battery could come loose and

cause injury.

11. Do not throw away battery with regular trash or dispose

in ﬁ re.

12. Store the battery in a location out of the reach of children.

13. Use the battery correctly in accordance with its

speciﬁ cations.

ADDITIONAL SAFETY WARNINGS

1. If the switch does not return to its original position,

immediately discontinue use and arrange for repairs with

the Hitachi Authorized Service Center.

2. Do not strike or apply strong impact to the switch panel.

Doing so can lead to damage.

3. While operating the tool:

 Make sure the rebar does not slant diagonally.

Rebar

 Keep the switch on until the piston reaches the tip.

 When switched on, the piston will not move forward until

it has completely returned. This is to ensure that the

next oil pressure is not applied while the hydraulic valve

inside the tool remains open.

4. Replace the blade at an early stage. Using a chipped

or deformed blade could result in injury from ﬂ ying

fragments.

5. Use the provided hex. bar wrench (4 mm) when installing

or removing the cutter block. Using a tool other than the

one provided may result in too much or not enough

tightening that can lead to injury.

6. When replenishing hydraulic oil:

 Always make sure it is done when the temperature of

both the tool and the hydraulic oil is cool. Removing the

oil plug while the tool is hot can result in the oil inside the

tool to spray out and cause accident or injury.

 Try to avoid inserting air when injecting the oil.

Pump case Hydraulic oil

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CF18DSL Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info