Bedienungsanleitung Hitachi CG10-DL (Seite 15 von 96) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

563833

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

English

⅜ Trees with luxuriant foliage should be trimmed

starting from the bottom and work up to achieve the

desired shape. (Fig. 21)

Trimming hedges

⅜ Trim the top of hedges by moving the tool from right

to left (or left to right) and trim the sides by starting

from below and working up. (Fig. 22)

NOTE

⅜ Do not use the tool for cutting the lawn or weeds.

Grass or weeds could stick to the blade.

⅜ Cut thick branches by gently pressing the blades

against the branch.

2. Trimming lawns [Grass shear]

CAUTION

⅜ Use only for cutting grass.

⅜ Stop the tool immediately should gravel or branches

enter the blade during trimming and remove the

battery.

Do not allow the motor to seize up as it could damage

the motor. Use a pair of tongs to gently remove

gravel from the blade. To prevent injury, keep hands,

fingers and other body parts away from the blade.

(1) Remove gravel and branches from the lawn to be

trimmed.

(2) Place the blade in the blade cover to prevent accidental

contact.

(3) Install the adjuster when required to adjust trimming

height.

(4) Install the battery in the tool.

(5) Press the Lock Off button and pull the switch to start

trimming.

Place the tool on the lawn and slide the tool forward.

(Fig. 23)

NOTE

⅜ Lubricate (using sewing machine oil, mineral oil, etc.)

the blade before starting and then every hour. Use an

adequate amount of oil and wipe away excess oil.

⅜ During work (for example, when taking rests) do not

leave the tool in a place exposed to direct sunlight or

high temperature. This will prevent proper cooling

and could result in damage.

⅜ Do not use the tool for work that exceeds its capacity.

Such operation could cause the motor to lock up or

slow down and will damage it.

⅜ Do not lower the front end of the blade to prevent

sand, gravel or soil from entering the blade and

damaging it by making it less sharp.

Trimming tall grass

Attempting to cut tall grass at one go will expose the

blade to excessive load and wear the blade. First

remove 1/3 of the height starting from the top before

trimming it to the desired height.

Trimming around stone walls and curbs

When trimming around curbs, move the blade

sideways along the curb. (Fig. 24)

This makes it possible to trim without leaving

untrimmed edges.

3. Continuous operating time

Approx. 30 minutes (depending on the work conditions)

MAINTENANCE AND INSPECTION

WARNING

⅜ Be sure to turn the tool off and remove the battery

from the tool before making inspections or carrying

out maintenance.

⅜ Do not disassemble to blade. Failure to heed this

warning may result in injury.

⅜ Use gloves, or cloth to protect your hands when

handling the blade. Failure to heed this warning may

result in injury.

Fig. 20

Fig. 21

Fig. 22

Fig. 23

Fig. 24

01Eng_CH10DL_WE 9/30/09, 16:0214

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CG10-DL Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info