Bedienungsanleitung Hitachi CG10 (Seite 13 von 96) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

563832

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

English

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (see Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger power cord to the receptacle

2. Insert the battery in the charger

Position the battery so that the nameplate faces

toward the nameplate of the charger and press in the

battery until it comes into contact with the bottom

plate (See Fig. 3).

Inserting the battery will turn on the charger (the

pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

The pilot lamp goes off to indicate that the battery is

fully charged.

CAUTION

If the battery is heated due to direct sunlight, etc., just

after operation, the charger pilot lamp may not light.

At that time cool the battery first, then start charging.

⅜ Regarding recharging time

Table 1 shows the recharging time required according

to the type of battery.

NOTE: The recharging time may vary according to the

ambient temperature.

3. Disconnect the charger’s power cord from the

receptacle

4. Hold the charger firmly and pull out the battery

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION

⅜ When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

⅜ If the battery charger does not work while the battery

is mounted correctly, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

FUNCTIONAL DESCRIPTION

1. Battery Level Warning Lamp

The battery level can be checked by pulling the trigger

switch while the power tool is in a no-load state. The

battery level warning lamp lights when the battery power

is very low. If this happens, charge the battery. (Fig. 4)

NOTE

⅜ The level at which the battery level warning lamp lights

may vary due to the ambient temperature, characteristics

of the battery, etc. and is intended only as a guide.

⅜ The battery level warning lamp may light when the

power tool is overloaded. This does not mean that

the battery power is very low.

Be sure to check the battery level while the tool is in a

no-load state.

2. Lock Off button (Fig. 5)

WARNING

Never lock the Lock Off button in depressed position.

Pulling back the switch would then cause the tool to

suddenly start operating, which could result in injury.

The tool will not start unless the Lock Off button is

pressed while the switch is pulled back.

The Lock Off button can be engaged by pressing it

either from the right or left.

When the switch is released, the Lock Off button

automatically disengages to prevent inadvertent

motor startup.

3. Blade case (Fig. 6) ( Standard accessory with CH10DL

(CG), CH10DL)

When the shrub shear blade is to be attached to or

removed from the tool, or when the shear is not used,

place the blade in the blade case to prevent injury.

4. Blade cover (Fig. 7) (Standard accessory with CH10DL

(CG), CG10DL)

When the grass shear blade is to be attached to or

removed from the tool, or when the shear is not used,

place the blade in the blade cover to prevent injury.

5. Blade box (Fig. 8) (Standard accessory with CH10DL

(CG))

Place the shrub shear blade and the grass shear

blade in the blade box when they are not used.

Also place the crank cam (B) in the blade box to

prevent losing it.

Table 1 Recharging time (approx. min.) at 20°C

Battery capacity (Ah)

1.5 Ah

BCL1015 40 min.

01Eng_CH10DL_WE 9/30/09, 16:0212

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CG10 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info