Bedienungsanleitung Hitachi CG24EBSP-SL (Seite 11 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

563754

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

English

Throttle wire / stop cord

Press the upper tab (9) and open the air cleaner cover. (Fig. 6)

Connect stop cords. (Fig. 7)

If the throttle outer end (10) is threaded on your unit, screw it and the

earth terminal (11) (if so equipped) into the cable adjuster stay (12)

all the way, and then tighten this cable end using the adjuster nut

(13) against the cable adjuster stay (12).

Connect throttle wire end (14) to carburetor (15) and install swivel

cap (16) (if so equipped) where is included in tool bag, onto swivel

(15) (Fig. 8).

Press the upper tab (9) and close the air cleaner cover. (Fig. 6)

Store stop cords (17) into the air cleaner cover. (Fig. 9)

Some models may come with the parts installed.

Installation of cutting attachment guard (Fig. 10 – 12)

NOTE

The guard bracket may come already mounted to the gear case

on some models.

Install the cutting attachment guard on drive shaft tube against

angle transmission. Tighten the guard bracket ﬁ rmly so that the

cutting attachment guard does not swing or move down during

operation.

Install the cutting attachment guard to the guard bracket, which also

secures the guard to the gear case using the two guard mounting

screws.

WARNING

If an incorrect or faulty guard is ﬁ tted, this may cause serious

personal injury.

CAUTION

Some cutting attachment guards are equipped with sharp line

limiters. Be careful with handling it.

When using a trimmer head with two piece type cutting attachment

guard, attach the guard extension to the cutting attachment guard.

(Fig. 11)

NOTE

○ When attaching the guard extension to the cutting attachment

guard, the sharp line limiter must be removed from the cutting

attachment guard, (if so installed).

○ To remove the guard extension, refer to the drawings. Wear

gloves as the extension has a sharp line limiter, then push the

four square tabs on the guard one by one in order. (Fig. 12)

Installation of cutting attachment

WARNING

Install the cutting attachment properly and securely as

instructed in the handling instructions.

If not attached properly or securely, it may come oﬀ and cause

serious and/or fatal injury.

Installation of semi-auto cutting head

1. Function

Automatically feeds more nylon cutting line when it is tapped at

low rpm (not greater than 4500 min

-1

Speciﬁ cations

Code No.

Type of

attaching screw

Direction of

rotation

Size of

attaching screw

6696454

Female screw Counterclockwise M10×P1.25-LH

6698639

Applicable nylon cord

Cord diameter: Φ2.4 mm Length: 4 m

2. Precautions

○ The case must be securely attached to the cover.

○ Check the cover, case and other components for cracks or

other damage.

○ Check the case and button for wear.

If the wear limit mark (18) on the case is no longer visible or

there is a hole in the bottom (19) of the button, change the new

parts immediately. (Fig. 13)

○ The cutting head must be securely mounted to the unit’s gear

case.

○ For outstanding performance and reliability, always use Hitachi

nylon cutting line. Never use wire or other materials that could

become a dangerous projectile.

○ If the cutting head does not feed cutting line properly, check

that the nylon line and all components are properly installed.

Contact Hitachi Authorized Service Centers if you need

assistance.

3. Installation (Fig. 14)

○ Install cutting head on gear case of grass trimmers/brush

cutters. The mounting nut is left-hand-threaded. Turn clockwise

to loosen/counterclockwise to tighten.

NOTE

○ Since the cutter holder cap is not used here, keep it for when a

metal blade is used, if so equipped.

○ Press the stopper pin (20) of the gear case in order to lock the

cutter holder.

4. Adjusting line length

○ Set the engine speed as low as possible and tap the head on

the ground. The nylon line will be drawn out about 3 cm with

each tap. (Fig. 15)

Also, you can extend the nylon line by hand but the engine must

be completely stopped. (Fig. 16)

○ Adjust the nylon line to the proper length of 11–14 cm before

each operation.

Installation of cutting blade (Fig. 17)

(If so equipped)

When installing a cutting blade, make sure that there are no cracks

or any damage in it and that the cutting edges are facing the correct

direction.

NOTE

○ When installing cutter holder cap (21), be sure to set concave

side upward.

○ Press the stopper pin (20) of the angle transmission in order

to lock the cutter holder (22). Please note that the cutter ﬁ xing

bolt or nut (23) has left-handed threads, (clockwise to loosen/

counter-clockwise to tighten). Tighten the ﬁ xing bolt or nut with

the box wrench.

CAUTION

○ Before operation, make sure the blade has been properly

installed.

○ If your unit is equipped with protection cover under a cutting

blade, check it for wear or cracks before operation. If any

damage or wear is found, replace it, as it is an article of

consumption.

○ You have to wear gloves when handling the cutting blade.

WARNING

For Hitachi heads, use only ﬂ exible, non-metallic line

recommended by the manufacturer. Never use wire or wire

ropes. They can break oﬀ and become a dangerous projectile.

OPERATING PROCEDURES

Fuel (Fig. 18)

WARNING

○ The trimmer is equipped with a two-stroke engine. Always run

the engine on fuel, which is mixed with oil.

Provide good ventilation, when fueling or handling fuel.

000Book_CG24EBSP_WE.indb 11000Book_CG24EBSP_WE.indb 11 2014/03/26 11:22:062014/03/26 11:22:06

Hitachi CG24EBSP-SL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info