Bedienungsanleitung Hitachi CH55Y (Seite 8 von 136) (Alle Sprachen)

661480

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

English

2. Replacing the blade

For your continued safety, blade inspection and

replacement on this tool should ONLY be performed by

a HITACHI AUTHORIZED SERVICE CENTER.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

4. Replacing supply cord

If the replacement of the supply cord is necessary, it has

to be done by Hitachi Authorized Service Center to avoid

a safety hazard.

5. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

6. Cleaning on the outside

When the hedge trimmer is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

7. Transport of the tool

Attach the blade case to the blade before carrying this

tool.

If you carry it without the blade case, the blade may

come in contact with your body, causing injury.

8. Storage

Store the hedge trimmer in a place out of reach of

children.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

TROUBLESHOOTING

Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your

dealer or the Hitachi Authorized Service Center.

Symptom Possible cause Remedy

Does not operate. The power plug is not plugged into the

power socket.

Plug the power cord into the power

socket.

Foreign matter is lodged in the blade. When there is foreign matter in the blade,

disconnect the plug from receptacle

and use a pair of tongs or similar tool to

remove it.

Take great care since the tool may start

operating when the foreign matter has

been removed.

Sap or rust may also prevent the blade

from operating. Use a wire brush or similar

tool to remove sap or rust.

The tool does not trim well. The blade has become dull. Use a brush or cloth to remove sap.

If cleaning the blade does not improve

its cutting ability, contact the HITACHI

AUTHORIZED SERVICE CENTER to

have the blade replaced.

The blade stopped because it was used

to cut a branch whose width exceeded the

blade’s cutting capacity.

NOTE

Work that will repeatedly cause the

blade to stop will eventually damage

the motor.

Some garden trees have wood that is very

hard and may be beyond the capacity of

the tool even if it is of a width that is within

normal capacity. Use a pair of pruning

shear to remove thick branches before

starting work.

An oblique cut may also exceed the

capacity of the tool since the length of

the cut increases. Be sure to trim thick

branches at right angles.

0000Book_CH45Y.indb 80000Book_CH45Y.indb 8 2017/03/15 9:52:332017/03/15 9:52:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CH55Y Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info