Bedienungsanleitung Hitachi CL10SA (Seite 7 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

565917

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

English

Fig. 5

2. Cutting fixed lengths

When cutting several studs to the same length,

using the equipment in the following way will making

cutting operations more efficient.

(1) First cut one stud to the required length, and then

use it as a fixed length guide.

(2) Insert the stud used as a fixed length guide in the

stud attachment hole found on the main unit stud

guide and use the hexagonal bar wrench to tighten

and secure the hex. socket hd. bolt. Adjust at this

time so that the distance between the end of the

stud used as a fixed length and the cutter is the

necessary length.

(3) Insert the stud for cutting in the cutter, aligning the

end with that of the stud used as a cutting guide,

and then cut the stud.

Fig. 6

3. Cutting studs that are already secured

When cutting studs that are suspended from the

ceiling or secured to walls or floors.

When inserting the stud in the cutter, the meshing

of the stud thread and cutter thread is unstable. In

such a case, after inserting the stud in the cutter,

lightly pull the trigger switch to close the cutter at

low speed and then completely mesh the stud and

the upper and lower cutters. Next, pull the trigger

switch all the way to cut the stud.

CAUTION

Use your left hand to hold the stud on the side

released by cutting to insure that it does not fall

unexpectedly.

Fig. 7

4. Removing the stud from the unit during cutting

operations

If you wish to remove the stud from the cutter

during cutting operation, pull the trigger switch

while pressing the forward/reverse-switching button

toward the side of

(Fig. 1-2), and then the motor

will run in reverse, allowing you to remove the stud

from the cutter. (Fig. 8)

CAUTIONS

⅜ When removing a stud that is suspended from

the ceiling, hold the main unit with both hands

to prevent any possibility of the stud falling.

⅜ Immediately turn off the switch once the cutter

is free from the stud. If you attempt to do this

with the switch turned on, the cutter might cut

into the stud again.

If you leave the switch on in a state where the

cutter is cut in the stud, some forced pressure

can be applied to the main unit, resulting in

damage.

⅜ When you operate the forward/reverse-switching

button at the position of

(Fig. 1-2), do not

release your finger from the forward/reverse-

switching button until the switch is turned off.

If you release your finger before the switch is

turned off, there can be a case where the bracket

(A) does not stop immediately.

Fig. 8

5. Using the hook

The hook can be used to hang up the unit temporarily

during operations (Fig. 9).

CAUTION

The hook should never be used to hang the unit

on your person.

When using the hook, check to make sure that the

main unit will not slip and fall, or become unstable

by the wind, etc.

Never hang the unit from your belt or trousers as

this could cause accidents.

Cutter

Bracket (B)

Stud

Correctly mesh

Necessary length

Hex. socket hd. bolt

Fixed length

guide (First cut

the stud to the

required length)

Stud

attachment hole

Stud suspended

from the ceiling

Forward/reverse

switching button

Trigger switch

01Eng_CL10SA_WE 08/12/15, 11:576

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CL10SA Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info