Bedienungsanleitung Hitachi CL14DSL (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

565919

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically designated

battery packs.

Use of any other battery packs may create a risk

of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal

to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

PRECAUTION:

Keep children and infirm persons away.

When not in use, tools should be stored out of reach of

children and infirm persons.

PRECAUTIONS FOR CORDLESS STUD

CUTTER

1. Never bring the cutter near your fingers when

operating the switch.

2. Do not use for cutting screws other than soft steel

studs. This tool is designed especially for cutting

of soft steel studs. Using this tool for brass or

stainless steel screws could cause distortions in

the screw threads, thereby preventing insertion of

nuts.

Never use to cut tempered bolts, screws of differing

sizes, reinforcing rods, etc.

3. Use by changing the special cutters according to

the size of the studs. Cutting with cutters of the

wrong size could damage to the continuous thread

studs or the cutter edges.

4. Make sure that the threads on the studs and those

on the cutter are correctly meshed before starting

to cut. Cutting when the threads are not meshed

could cause damage to the studs and the cutter.

5. If the cutter has been attached in the wrong

direction or the bolt for cutter attachment is loose,

this could cause damage to the cutter edge and

could lead to premature damage to the main unit.

Be very careful to attach the cutter correctly.

6. Cutting studs at short lengths of 10 millimeters

or less will create an insufficient meshing length

between the cutter and studs, thus causing damage

to the cutter. Always cut at lengths of more than

10 millimeters.

7. When cutting studs secured to narrow locations,

be sure that there is at least 8 millimeters between

the stud and the surrounding materials.

If the distance is less than 8 millimeters the cutter

could contact the surrounding materials, thereby

causing damage to the cutter and the main unit.

8. When inspecting, cleaning or replacing the cutter,

be sure to remove the battery from the main unit.

The switch could be turned on accidentally, thereby

causing accidents.

9. When using this equipment at heights, make

doubly sure prior to use that there is no one

standing in the area immediately below you. Place

the tool in a safe and stable place when not using

at the moment.

10. Always charge the battery at a temperature of 0

– 40°C. A temperature of less than 0°C will result

in over charging which is dangerous. The battery

cannot be charged at a temperature greater than

40°C. The most suitable temperature for charging

is that of 20 – 25°C.

11. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

12. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

13. Never disassemble the rechargeable battery and

charger.

14. Never short-circuit the rechargeable battery. Short-

circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

15. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

16. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

17. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

18. Using an exhausted battery will damage the

charger.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 and 2 described below, when using

this product, even if you are pulling the switch, the

motor may stop. This is not the trouble but the result

of protection function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

Furthermore, please heed the following warning and

caution.

01Eng_CL14DSL_WE 08/3/6, 19:137

Hitachi CL14DSL Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info