Bedienungsanleitung Hitachi CM9UBY (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

565940

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

5) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach of

children and infirm persons.

CUTTER SAFETY WARNINGS

a) Read all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

b) Always use guard provided with the tool. The guard

must be securely attached to the power tool and

positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. Position

yourself and bystanders away form the plane of the

rotating wheel.

The guard helps to protect operator from broken

wheel fragments and accidental contact with wheel.

c) Use only flat reinforced or diamond cut-off wheels

for your power tool.

Just because an accessory can be attached to your

power tool, it does not assure safe operation.

d) The rated speed of the wheel must be at least equal

to the maximum speed marked on the power tool.

Wheels running faster than their rated speed can

break and fly apart.

e) Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may

cause them to shatter.

f) Always use undamaged wheel flanges that are of

correct diameter for your selected wheel.

Proper wheel flanges support the wheel thus reducing

the possibility of wheel breakage.

g) Do not use worn down flat reinforced wheels from

larger power tools.

Wheels intended for a larger power tool are not

suitable for the higher speed of a smaller tool and

may burst.

h) The outside diameter and the thickness of your

wheel must be within the capacity rating of your

power tool.

Incorrectly sized wheels cannnot be adequately

guarded or controlled.

i) The arbour size of wheels and flanges must properly

fit the spindle of the power tool.

Wheels and flanges with arbour holes that do not

match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause

loss of control.

j) Do not use damaged wheels. Before each use,

inspect the wheels for chips and cracks. If power

tool or wheel is dropped, inspect for damage or

install an undamaged wheel. After inspecting and

installing the wheel, position yourself and bystanders

away from the plane of the rotating wheel and run

the power tool at maximum no load speed for one

minute.

Damaged wheels will normally break apart during

this test time.

k) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and shop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust

mask or respirator must be capable of filtrating

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing

loss.

l) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.

Fragments of wheel or of a broken accessory may

fly away and cause injury beyond immediate area of

operation.

m) Hold power tool by insulated gripping surfaces only,

when performing an operation where the wheel may

contact hidden wiring or its own cord.

Wheel contacting a”live” wire may make exposed

metal parts of the power tool “live” and shock the

operator.

n) Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

wheel.

o) Never lay the power tool down until the wheel has

come to a complete stop.

The spinning wheel may grab the surface and pull

the power tool out of your control.

p) Do not run the power tool while carrying it at your

side.

Accidental contact with the spinning wheel could

snag your clothing, pulling the wheel into your body.

q) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

r) Do not operate the power tool near flammable

materials.

Sparks could ignite these materials.

s) Do not use wheels that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged

rotating wheel. Pinching or snagging causes rapid stalling

of the rotating wheel which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

wheel’s rotation at the point of the binding.

a) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up.

The operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating wheel.

Wheel may kickback over your hand.

c) Do not position your body in line with and behind

the rotating wheel.

01Eng_CM9SR_WE 6/30/08, 18:166

Hitachi CM9UBY Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info