Bedienungsanleitung Hitachi CP-A300N (Seite 17 von 22) (Englisch)

467146

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

ENGLISH

The air lter has two kinds of lters inside. Please check and clean the air lter periodically.

When the indicators or a message prompts you to clean the air lter, comply with it as soon

as possible. If the lters are damaged or heavily soiled, replace them with the new ones. To

prepare the new lters, make contact with your dealer and tell the following type number.

Type number : UX37191 (Filter set)

When you replace the lamp, please replace the air lter. An air lter of specied type will

come together with a replacement lamp for this projector.

Turn the projector off, and unplug the power cord. Allow

the projector to sufciently cool down.

Use a vacuum cleaner on and around the lter cover.

Slide the lter unit upward to take it off from the projector.

Use a vacuum cleaner for the lter vent of the projector.

Take the ne meshed lter out while holding the lter

cover. It is recommended to leave the coarse meshed

lter in the lter cover as it is.

Use a vacuum cleaner on both sides of the ne meshed

lter while holding it so it will not be sucked in. Use a

vacuum cleaner for the inside of the lter cover to clean

up the coarse meshed lter. If the lters are damaged

or heavily soiled, replace them with new ones.

Put the ne meshed lter on the coarse meshed one,

turning its stitched side up.

Put the lter unit back into the projector.

Turn the projector on and reset the lter time using the

FILTER TIME item in the EASY MENU.

(1) Press the MENU button to display a menu.

(2) Point at the FILTER TIME using the ▼/▲ button, then press

the ► button. A dialog will appear.

(3) Press the ► button to select “OK” on the dialog. It performs resetting the lter time.

Cleaning and replacing the air lter

WARNING ►Before taking care of the air lter, make sure the power cable

is not plugged in, then allow the projector to cool sufciently.

►

Use only the air lter of the specied type. Do not use the projector without the

air lter or the lter cover. It could result in a re or malfunction to the projector

►

Clean the air lter periodically. If the air lter becomes clogged by dust or the like,

internal temperatures rise and could cause a re, a burn or malfunction to the projector.

NOTE • Please reset the lter time only when you have cleaned or replaced

the air lter, for a suitable indication about the air lter.

• The projector may display the message such as the “CHECK THE AIR FLOW”

or turn off the projector, to prevent the internal heat level rising.

Filter cover

Filter unit

Intake vent

Stitched

side

Filter cover

Filter

(coarse meshed)

Filter (ne meshed)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CP-A300N Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi CP-A300N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info