505782
27
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
27
Operating
Most of operations are effective for the main area
only. Also the audio input signal paired with the
picture input signal for the main area is assigned
as the audio output signal. The main area can be
changed using the cursor buttons ◄/► when the
setting information is on the screen.
PbyP (Picture by Picture)
The PbyP is a function to display two different picture signals on a screen that is
split in two areas for each signal. Some of functions can be used with the same
operation as it for the normal mode (not in the PbyP mode). There are some
operations available only in the PbyP mode.
The setting information is displayed for several
seconds when the PbyP function is started. It shows
the input signal information for each area. Also, there
will be a yellow frame with one of the area that is the main area where most
of operations are effective. The information can be displayed using the cursor
buttons ▲/▼/◄/► when the setting information is not on the screen.
Press the
PbyP button on the
remote control, then the PbyP
function will be started. To quit
the PbyP mode, press the button
again.
Press the COMPUTER, VIDEO or DIGITAL button
while in the PbyP mode, the menu to select the
input signal will be appeared. Choose a signal using
the cursor buttons ▲/▼. If you want to change the signal in
the sub area, switch the main area using the cursor buttons
◄/► rst. Displaying the same signal on the both areas is
not allowed. For other combinations of the input signal, refer
to the right table. Any combinations marked with X can not be
selected.
<signal combination>
Press the MY BUTTON assigned the PbyP SWAP
(49). The position of the both area is exchanged
without any setting change.
Starting the PbyP
Changing the main area
Showing the setting information
Changing the picture input signal
Using the PbyP SWAP function
normal mode PbyP mode
•For some signals, it may not be displayed correctly in the PbyP mode,
even if it can be displayed properly in the normal mode.
NOTE
main area
sub area
main area
Sub
Main
COMPUTER IN1
COMPUTER IN2
BNC
HDMI
DVI-D
Component
Scart RGB
S-Video
Video 1
Video 2
COMPUTER IN1
0 0 0 0 0 0 0 0 0
COMPUTER IN2
0 0 0 0 0 0 0 0 0
BNC 0 0 0 0 0 0 0 0 0
HDMI 0 0 0 X 0 X X X X
DVI-D 0 0 0 X 0 X X X X
Component
0 0 0 0 0 0 0 0
Scart RGB
0 0 0 X X X X X
S-Video
0 0 0 X X 0 X X X
Video 1
0 0 0 X X 0 X X X
Video 2
0 0 0 X X 0 X X X
BLANK LASER
FREEZE
LASER
INDICATOR
DIGITAL
STANDBY/ON COMPUTER
LENS SHIFT
KEYSTONE
ID 3
ID 4
ID 2
ID 1
VIDEO
AUTO
ASPECT
RESET
MENU
MAGNIFY
ON
OFF
3
4
ENTER
FOCUS
+
-
POSITION
PbyP
ZOOM
+
-
1
2
MY BUTTON
MY SOURCE
SHUTTER
setting information
27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hitachi CP-SX12000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hitachi CP-SX12000

Hitachi CP-SX12000 Bedienungsanleitung - Deutsch - 172 seiten

Hitachi CP-SX12000 Bedienungsanleitung - Holländisch - 172 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info