505782
34
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
34
IMAGE menu
IMAGE menu
From the IMAGE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons on the
projector or remote control, and press the ► cursor
button on the projector or remote control, or
ENTER
button on the remote control to execute the item.
Then perform it according to the following table.
Item Description
ASPECT
Using the ▲/▼ buttons switches the mode for aspect ratio.
For a COMPUTER signal
NORMAL
ó
4:3
ó
16:9
ó
16:10*
ó
SMALL*
ó
NATIVE*
ó
FULL*
For an HDMI or DVI-D signal
NORMAL
ó
4:3
ó
16:9
ó
16:10*
ó
14:9
ó
SMALL*
ó
NATIVE*
ó
FULL*
For a Video signal, S-video signal or component video signal
4:3
ó
16:9
ó
16:10*
ó
14:9
ó
SMALL*
ó
NATIVE*
ó
FULL*
For no signal
4:3 (xed, except CP-WX11000) / FULL (xed, CP-WX11000)
• *16:10 / FULL: CP-WX11000 only. NATIVE: Except CP-X10000.
SMALL: Except CP-WX11000.
• The NORMAL mode keeps the original aspect ratio of the signal.
OVER SCAN
Using the ◄/► buttons adjusts the over-scan ratio.
Small (It magnies picture)
ó
Large (It reduces picture)
This item can be selected not only for a video, s-video and component signal but also
HDMI and DVI-D signal when the VIDEO is selected on the DIGITAL FORMAT item (
37)
.
• When this adjustment is too large, certain degradation may appear
at the frame area of the picture. In such a case, please adjust small.
V POSITION
Using the ◄/► buttons adjusts the vertical position.
Down
ó
Up
Over-adjusting the vertical position may cause noise to appear on the screen. If this
occurs, please reset the vertical position to the default setting. Pressing the
RESET
button when the V POSITION is selected will reset the V POSITION to the default setting.
When this function is performed on a video signal, s-video signal, or component video
signal of 480i@60 or 576i@50 input the range of this adjustment depends on the OVER
SCAN
(
above)
setting. It is not possible to adjust when the OVER SCAN is set to 10.
• This item cannot be selected for an HDMI or DVI-D signal.
H POSITION
Using the ◄/► buttons adjusts the horizontal position.
Right
ó
Left
Over-adjusting the horizontal position may cause noise to appear on the screen. If this
occurs, please reset the horizontal position to the default setting. Pressing the
RESET
button when the H POSITION is selected will reset the H POSITION to the default setting.
When this function is performed on a video signal, s-video signal, or component video
signal of 480i@60 or 576i@50 input the range of this adjustment depends on the OVER
SCAN
(
above)
setting. It is not possible to adjust when the OVER SCAN is set to 10.
• This item cannot be selected for an HDMI or DVI-D signal.
(continued on next page)
34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hitachi CP-SX12000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hitachi CP-SX12000

Hitachi CP-SX12000 Bedienungsanleitung - Deutsch - 172 seiten

Hitachi CP-SX12000 Bedienungsanleitung - Holländisch - 172 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info