505782
67
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
67
Maintenance
Maintenance
A worn out lamp bulb could burn or burst. It is recommended to keep a spare
lamp unit on hand and to replace the lamp unit when the projected image darkens
or color reproduction becomes poor.
To prepare the spare, contact your dealer and tell the following type number.
Lamp unit
Type number of the optional lamp unit: DT01001
•The value shown on the OPTION menu as the LAMP TIME is the use
time that is counted since the last time the LAMP TIME was reset. Refer to the
value for proper maintenance.
NOTE
If the projector is installed in a special state such as ceiling mount, or if the lamp
bulb has broken, also ask the dealer to replace the lamp unit. Otherwise, follow
the procedure shown below to replace the lamp.
Make sure that the projector is unplugged and
cooled down.
1.
6.
To display the ADVANCED MENU, press the MENU button (on the control
panel or the remote control). On the EASY MENU, select the “ADVANCED
MENU” using the ▲/▼ cursor buttons, then press the ► cursor button.
To display the LAMP TIME dialog, select the
LAMP TIME” using the ▲/▼ cursor buttons in
the right column, then press the ► cursor button.
Use the ► cursor button according to the dialog,
Selecting “OK” resets the LAMP TIME value.
(1)
(2)
(4)
(5)
Turn the projector on.
I O
HDMI DVI-D
CONTROL IN CONTROL OUT
REMOTE
CONTROL
IN
OUT
S-VIDEO
COMPUTER IN2
COMPUTER IN1
VIDEO 1
BNC
R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2
Y
Cb/Pb
Cr/Pr
AC IN
LAN
MONITOR
OUT
The lamp cover
The handles
Loosen the screw (marked by arrow) of the
lamp cover. Then slide and take it off.
2.
Loosen the 3 screws (marked by arrow) of the
lamp unit. Then picking the handles of the unit,
gently take it from the projector.
3.
Gently set the new lamp unit into place. Then
retighten the screws of the lamp unit.
4.
Put the lamp cover back into place, and
retighten the screw of the lamp cover.
5.
Reset the LAMP TIME value.
►Be sure to reset the LAMP TIME only when you have replaced the
lamp unit.
NOTICE
To select the OPTION menu, select the
OPTION” using the ▲/▼ cursor buttons in the
left column, then press the ► cursor button.
(3)
67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hitachi CP-SX12000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hitachi CP-SX12000

Hitachi CP-SX12000 Bedienungsanleitung - Deutsch - 172 seiten

Hitachi CP-SX12000 Bedienungsanleitung - Holländisch - 172 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info