505782
73
Zoom out
Zoom in
Vorherige Seite
1/78
Nächste Seite
73
Troubleshooting
• When the interior portion has become overheated, for safety
purposes, the power source is automatically turned off, and the indicator lamps
may also be turned off. In such a case, press the “O” (off) side of the power
switch, and wait at least 45 minutes. After the projector has sufciently cooled
down, please make conrmation of the attachment state of the lamp and lamp
cover, and then turn the power on again.
NOTE
POWER TEMP LAMP
SECURITY
SHUTTER
Description
Blinking
In Red
or
Lighting
In Red
Blinking
In Red
Turned
off
Turned
off
Turned
off
The cooling fan is not operating.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufciently cooled down, please make conrmation that
no foreign matter has become caught in the fan, etc.,
and then turn the power on again.
If the same indication is displayed after the remedy,
please contact your dealer or service company.
Blinking
In Red
or
Lighting
In Red
Lighting
In Red
Turned
off
Turned
off
Turned
off
The internal temperature is rising too much.
Turn the projector off (
20) soon, and allow it to cool
down for 20 minutes or more. After cooling, perform the
following check.
- Are there any obstacles to ventilation around the
projector?
- Does the temperature around the projector exceed the
limit specied? (
77)
When this message is displayed without the obstacles
mentioned above, replacement of the lter unit is
required. Replace the lter unit soon according to the
procedure directed in the paragraph "Filter unit" in the
chapter "Maintenance" (
69). Remember resetting the
FILTER TIME is needed soon after replacement of the
lter unit.
Lighting
In
Green
Simultaneous
blinking in Red
Turned
off
Turned
off
Replacement of the lter unit is required.
The value of the timer of the FILTER TIME reached the
preset value of the FILTER MESSAGE on the SERVICE
menu under the OPTION menu (
50). Replace the
lter unit soon according to the procedure directed in the
paragraph "Filter unit" in the chapter "Maintenance" (
69).
Remember resetting the FILTER TIME is needed soon
after replacement of the lter unit.
Lighting
In
Green
Alternative
blinking in Red
Turned
off
Turned
off
There is a possibility that the interior portion has
become overcooled.
Please use the unit within the usage temperature
parameters (5°C to 35°C). After the treatment, reset the
power to on.
Blinking
in
Green
for
approx.
3
seconds
Turned
off
Turned
off
Turned
off
Turned
off
At least 1 “Power ON” schedule is saved to the
projector.
(Please refer to the
User’s Manual - Network Guide:
Schedule Settings for more information.)
73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hitachi CP-SX12000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hitachi CP-SX12000

Hitachi CP-SX12000 Bedienungsanleitung - Deutsch - 172 seiten

Hitachi CP-SX12000 Bedienungsanleitung - Holländisch - 172 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info