Bedienungsanleitung Hitachi CP-X2515WN (Seite 109 von 123) (Englisch)

505798

109

Zoom out

Zoom in

Vorherige Seite

1/123

Nächste Seite

109

Maintenance

Lamp warning

Replacing the lamp (continued)

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►

The projector uses a high-pressure mercury glass lamp. The lamp

can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or

worn over time. Note that each lamp has a different lifetime, and some may burst or

burn out soon after you start using them. In addition, if the bulb bursts, it is possible

for shards of glass to ﬂy into the lamp housing, and for gas containing mercury and

dust containing ﬁne particles of glass to escape from the projector’s vent holes.

►About disposal of a lamp: This product contains a mercury lamp; do not put

it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency

or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

WARNING

• If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a

replacement lamp from your local dealer. Note that shards of glass

could damage the projector’s internals, or cause injury during handling,

so please do not try to clean the projector or replace the lamp yourself.

•

If the lamp should break (it will make a loud bang when it does), ventilate the

room well, and make sure not to inhale the gas or ﬁne particles that come out

from the projector's vent holes, and not to get them into your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from

a ceiling. This is dangerous, since if the lamp’s bulb has broken, the

shards will fall out when the cover is opened. In addition, working in

high places is dangerous, so ask your local dealer to have the lamp

replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose

screws could result in damage or injury.

• Use only the lamp of the specified type. Use of a lamp that does not

meet the lamp speciﬁcations for this model could cause a ﬁre, damage or

shorten the life of this product.

• If the lamp breaks soon after the first time it is used, it is possible

that there are electrical problems elsewhere besides the lamp. If this

happens, consult your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•

Using the lamp for long periods of time, could cause it dark, not to light up or to burst.

When the pictures appear dark, or when the color tone is poor, please replace the

lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

Disconnect

the plug

from the

power

outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CP-X2515WN Seite 109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi CP-X2515WN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info