Bedienungsanleitung Hitachi CP-X4015WN (Seite 249 von 259) (Englisch)

505800

249

Zoom out

Zoom in

Vorherige Seite

1/259

Nächste Seite

ENGLISH

Please check and clean the air ﬁlter periodically. When the indicators or a message

prompts you to clean the air ﬁlter, comply with it as soon as possible. The air ﬁlter has two

kinds of ﬁlters inside. Replace the ﬁlters when they are damaged or too soiled. To prepare

the new ﬁlters, make contact with your dealer and tell the following type number.

Type number : MU06481 (Filter set)

When you replace the lamp, please replace the air ﬁlter. An air

ﬁlter of speciﬁed type will come together with a replacement

lamp for this projector.

Turn the projector off, and unplug the power cord. Allow the

projector to sufﬁciently cool down.

Use a vacuum cleaner on and around the ﬁlter cover.

While supporting the projector with one hand, use your

other hand to pull the ﬁlter cover forward in the direction of

the arrow.

Use a vacuum cleaner for the ﬁlter vent of the projector

and the outer side of the ﬁlter unit.

Take the ﬁlters out while holding the ﬁlter cover.

Use a vacuum cleaner on both sides of the ﬁlters. When

vacuuming up the ﬁne meshed ﬁlter, hold it so it will not

be sucked in. If the ﬁlters are damaged or heavily soiled,

replace them with the new ones.

Put the ﬁlters back into the ﬁlter cover. Put the coarse

meshed ﬁlter into a ﬁlter cover ﬁrst. Then put the ﬁne

meshed ﬁlter on the coarse meshed one, turning its

stitched side up.

Put the ﬁlter unit back into the projector.

Turn the projector on and reset the ﬁlter time using the

FILTER TIME item in the EASY MENU.

(1) Press the MENU button to display a menu.

(2) Point at the FILTER TIME using the ▼/▲ button, then press

the ► button. A dialog will appear.

(3) Press the ► button to select “OK” on the dialog. It performs

resetting the ﬁlter time.

Cleaning and replacing the air ﬁlter

WARNING ►Before taking care of the air ﬁlter, make sure the power cable

is not plugged in, then allow the projector to cool sufﬁciently.

►

Use only the air ﬁlter of the speciﬁed type. Do not use the projector without the

air ﬁlter or the ﬁlter cover. It could result in a ﬁre or malfunction to the projector

►

Clean the air ﬁlter periodically. If the air ﬁlter becomes clogged by dust or the like,

internal temperatures rise and could cause a ﬁre, a burn or malfunction to the projector.

NOTE • Please reset the ﬁlter time only when you have cleaned or replaced

the air ﬁlter, for a suitable indication about the air ﬁlter.

• The projector may display the message such as “CHECK THE AIR FLOW” or

turn off the projector, to prevent the internal heat level rising.

Filter cover

Filter unit

Filter cover

Filter (ﬁne meshed)

Filter (coarse meshed)

Stitched

side

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CP-X4015WN Seite 249

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi CP-X4015WN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info