Bedienungsanleitung Hitachi cprx80 lcd projektor (Seite 86 von 95) (Englisch)

215933

Zoom out

Zoom in

Vorherige Seite

1/95

Nächste Seite

ENGLISH

HIGH VOLTAGE

HIGH TEMPERATURE HIGH PRESSURE

WARNING ŹThe projector uses a high-pressure mercury glass lamp. The

lamp can break with a loud bang, or burn out, if jolted or scratched, handled

while hot, or worn over time. Note that each lamp has a different lifetime, and

some may burst or burn out soon after you start using them. In addition, when

the bulb bursts, it is possible for shards of glass to ﬂ y into the lamp housing,

and for gas containing mercury to escape from the projector’s vent holes.

ŹAbout disposal of a lamp: This product contains a mercury lamp; do not put

it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency

or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, ask your dealer.

• If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a

replacement lamp from your local dealer. Note that shards of glass

could damage the projector’s internals, or cause injury during handling,

so please do not try to clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does),

ventilate the room well, and make sure not to breathe the gas that

comes out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from

a ceiling. This is dangerous, since if the lamp’s bulb has broken, the

shards will fall out when the cover is opened. In addition, working in

high places is dangerous, so ask your local dealer to have the lamp

replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose

screws could result in damage or injury.

• Use only the lamp of the speciﬁ ed type.

• If the lamp breaks soon after the first time it is used, it is possible

that there are electrical problems elsewhere besides the lamp. If this

happens, consult your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time, could cause it dark, not to light

up or to burst. When the pictures appear dark, or when the color tone

is poor, please replace the lamp as soon as possible. Do not use old

(used) lamps; this is a cause of breakage.

Disconnect

the plug

from the

power

outlet

Replacing the lamp (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi cprx80 lcd projektor Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info