Bedienungsanleitung Hitachi CPX11WN (Seite 9 von 242) (Englisch)

505867

Zoom out

Zoom in

Vorherige Seite

1/242

Nächste Seite

• If the lamp should break (it will make a loud bang when it does), unplug

the power cord from the outlet, and make sure to request a replacement

lamp from your local dealer. Note that shards of glass could damage the

projector’s internals, or cause injury during handling, so please do not try to

clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does), ventilate

the room well, and make sure not to breathe the gas that comes out of the

projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the

power cable is not plugged in, then wait at least 45 minutes for the lamp to

cool sufficiently. Handling the lamp while hot can cause burns, as well as

damaging the lamp.

Lamp

The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after

you start using them. In addition, when the bulb bursts, it is possible for shards of

glass to fly into the lamp housing, and for gas containing mercury to escape from the

projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash.

Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US)

or www.epsc.ca (in Canada).

For more information, call your dealer.

• Do not open the lamp cover while the projector is suspended from above.

This is dangerous, since if the lamp’s bulb has broken, the shards will

fall out when the cover is opened. In addition, working in high places is

dangerous, so ask your local dealer to have the lamp replaced even if the

bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose screws

could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that

there are electrical problems elsewhere besides the lamp. If this happens,

contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst

during use.

• Using the lamp for long periods of time, could cause it dark, not to light up

or to burst. When the pictures appear dark, or when the color tone is poor,

please replace the lamp as soon as possible. Do not use old (used) lamps;

this is a cause of breakage.

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

Disconnect

the plug from

the power

outlet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CPX11WN Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi CPX11WN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info