382971
12
Zoom out
Zoom in
Vorherige Seite
1/66
Nächste Seite
11
English
(2) Trigger switch
This tool is equipped with a variable speed controlled
trigger switch. The tool can be turned "ON" or "OFF"
by squeezing or releasing the trigger. The blade
plunger stroke rate can be adjusted from the
minimum to maximum nameplate stroke rate by
the pressure you apply to the trigger. Apply more
pressure to increase the speed and release pressure
to decrease speed.
2. Cutting metallic materials
CAUTION
Press the base firmly against the workpiece.
Never apply any unreasonable force to the saw
blade when cutting. Doing so can easily break the
blade.
The motor can be locked sometimes, depending on
the combination of the material to be cut and the
blade. Whenever the motor gets locked, switch it
off immediately.
(1) Fasten a workpiece firmly before operation. (Fig. 21)
(2) When cutting metallic materials, use proper machine
oil (turbine oil, etc.). When not using liquid machine
oil, apply grease over the workpiece.
CAUTION
The service life of the saw blade will be drastically
shortened if you don’t use machine oil.
3. Cutting lumber
When cutting lumber, make sure that the workpiece
is fastened firmly before beginning. (Fig. 22)
CAUTION
Never apply any unreasonable force to the saw
blade when cutting. Also remember to press the
base against the lumber firmly.
4. Sawing curved lines
We recommend that you use the BI-METAL blade
mentioned in Table 5 for the saw blade since it is
tough and hardly breaks.
CAUTION
Delay the feed speed when cutting the material into
small circular arcs. An unreasonably fast feed may
break the blade.
5. Plunge cutting
With this tool, you can perform plunge cutting on
plywood panels and thin board materials. You can
carry out pocket cutting quite easily with the saw
blade installed in reverse as illustrated in Fig. 24,
Fig. 26, and Fig. 28. Use the saw blade that is as
short and thick as possible. We recommend for this
purpose that you use BI-METAL Blade No. 132
mentioned in Table 5. Be sure to use caution during
the cutting operation and observe the following
procedures.
(1) Press the lower part (or the upper part) of the base
against the material. Pull the switch trigger while
keeping the tip of the saw blade apart from the
material. (Fig. 23, Fig. 24)
(2) Raise the handle slowly and cut in with the saw
blade little by little. (Fig. 25, Fig. 26)
(3) Hold the body firmly until the saw blade completely
cuts into the material. (Fig. 27, Fig. 28)
CAUTION
Avoid plunge cutting for metallic materials. This can
easily damage the blade.
Never pull the switch trigger while the tip of the
saw blade is pressed against the material. If you
do so, the blade can easily be damaged when it
collides with the material.
Make absolutely sure that you cut slowly while
holding the body firmly. If you apply any
unreasonable force to the saw blade during the
cutting operation, the blade can easily be damaged.
NOTE
The use of the battery EB2430HA in a cold condition
(below 0 degree Centigrade) can sometimes result
in the weakened cutting torque and reduced amount
of work. This, however, is a temporary phenomenon,
and returns to normal when the battery warms up.
SELECTION OF BLADES
To ensure maximum operating efficiency and results,
it is very important to select the appropriate blade best
suited to the type and thickness of the material to be
cut.
NOTE:
Dimensions of the workpiece mentioned in the table
represent the dimensions when the mounting
position of the base is set nearest to the body of
the Cordless Reciprocating Saw. Caution must be
exercised since dimensions of the workpiece will
become smaller if the base is mounted far away
from the body of the Cordless Reciprocating Saw.
1. Selection of HCS blades
The blade number of HCS blades in Table 4 is
engraved in the vicinity of the mounting position
of each blade. Select appropriate blades by referring
to Tables 4 and 6 below.
Table 4: HCS blades
NOTE
No. 1 – No. 96 HCS blades are sold separately as
optional accessories.
2. Selection of BI-METAL blades
The BI-METAL blade numbers in Table 5 are
described on the packages of special accessories.
Select appropriate blades by referring to Table 5
and 6 below.
Blade Thickness
No.
Uses
(mm)
No. 1 For cutting steel pipe less than
100 mm in diameter
2.5 – 6
No. 2 For cutting steel pipe less than
30 mm in diameter
2.5 – 6
No. 3 For cutting steel pipe less than
30 mm in diameter
Below 3.5
No. 4 For cutting and roughing lumber 50 – 70
No. 5 For cutting and roughing lumber Below 30
No. 8 For cutting vinyl chloride pipe less
than 100 mm in diameter
2.5 – 15
For cutting and roughing lumber Below 100
No. 9 For cutting mild steel pipe less
than 100 mm in diameter when 2.5 – 6
used with cut off guide
No. 95 For cutting stainless steel pipe
less than 100 mm in diameter
Below 2.5
No. 96 For cutting stainless steel pipe
less than 30 mm in diameter
01Eng_CR24DV_WE 11/9/07, 10:5211
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hitachi cr 24 dv wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info