Bedienungsanleitung Hitachi CR14DSL (Seite 12 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

565954

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

(2) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

Table 2 Recharging ranges of batteries

⅜ (1) – (9) : HCS Blades (HCS : Highspeed Carbon

Steel)

⅜ (10) – (20) : Bl-METAL Blades

Refer to Table 5, 6 and 7 for use of the blades.

Optional accessories are subject to change without

notice.

APPLICATIONS

⅜ Cutting pipe and angle steel.

⅜ Cutting various lumbers.

⅜ Cutting mild steel plates, aluminum plates, and

copper plates.

⅜ Cutting synthetic resins, such as phenol resin and

vinyl chloride.

For details refer to the section entitled “SELECTION OF

BLADES”.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latches

(2 pcs.) to remove the battery (See Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

Table 1

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Blinks

Lights

Blinks

Flickers

Lights

Malfunction in the

battery or the charger

Battery overheated.

Unable to charge

(Charging will commence

when battery cools).

Overheat

Standby

The

pilot

lamp

lights or

blinks in

red.

The

pilot lamp

lights in

green.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the power tool, charge the battery as

follows.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals)

2. Insert the battery into the charger.

Firmly insert the battery into the charger until the

line is visible, as shown in Fig. 3, 4.

3. Charging

When inserting a battery in the charger, charging

will commence and the pilot lamp will light

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals) (See

Table 1)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown

in Table 1, according to the condition of the charger

or the rechargeable battery.

Temperatures at

Rechargeable batteries

which the battery

can be recharged

BSL1430, BSL1830

0°C – 50°C

Charger

UC18YRSL

Battery

BSL1430, BSL1830 Approx. 45 min.

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown

in Table 3.

Table 3 Charging time (At 20°C)

NOTE:

The charging time may vary according to

temperature and power source voltage.

01Eng_CR14DSL_WE 6/4/08, 11:5811

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CR14DSL Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info