Bedienungsanleitung Hitachi CR14DSL (Seite 16 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

565954

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

Material Material Thickness

Blade No.

to be cut quality (mm)

Iron plate Mild steel 2.5 – 10 No. 1, 2, 101,

plate 102, 103, 104,

105, 106, 131

Below 3.5 No. 3, 107,

108

Nonferrous Aluminium, 5 – 20 No. 1, 2, 101,

metal Copper and 102, 103, 104,

Brass 105, 106, 131,

132

Below 5 No. 3, 107,

108

Systhetic Phenol resin, 10 – 50 No. 1, 2, 4,

resin Melamine 101, 102, 103,

resin, etc. 104, 131, 132

5 – 30 No. 3, 5, 8,

105, 106, 107,

108

Vinyl chloride,

10 – 60 No. 1, 2, 4,

Acrylic resin, 101, 102, 103,

etc. 104, 131, 132

5 – 30 No. 3, 5, 8,

105, 106, 107,

108

3. Selection of blades for other materials

Table 7

MAINTENANCE AND INSPECTION

CAUTION

Be sure to turned off the switch and remove the

battery before maintenance and inspection.

1. Inspecting the blade

Continued use of a dull or damaged blade will

result in reduced cutting efficiency and may cause

overloading of the motor. Replace the blade with

a new one as soon as excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

4. Inspecting the carbon brushes (Fig. 31)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the "wear limit". In addition, always

keep carbon brushes clean and ensure that they

slide freely within the brush holders.

NOTE

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999058.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 33.

When installing the carbon brush, choose the

direction so that the nail of the carbon brush agrees

with the contact portion outside the brush tube.

Then push it in with a finger as illustrated in

Fig. 34. Lastly, install the brush cap.

CAUTION

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube (You can insert whichever one of the two nails

provided).

Caution must be exercised since any error in this

operation can result in the deformed nail of the carbon

brush and may cause motor trouble at an early stage.

6. Cleaning of the outside

When the Cordless Reciprocating Saw is stained,

wipe with a soft dry cloth or a cloth moistened with

soapy water. Do not use chloric solvents, gasoline

or paint thinner, as they melt plastics.

7. Storage

Store the Cordless Reciprocating Saw in a place in

which the temperature is less than 40°C, and out

of reach of children.

8. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee

does not cover defects or damage due to misuse, abuse,

or normal wear and tear. In case of complaint, please

send the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

01Eng_CR14DSL_WE 6/4/08, 11:5815

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CR14DSL Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info