Bedienungsanleitung Hitachi CS40EA (Seite 14 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566225

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

English

Guide bar (Fig. 35)

Before using the machine, clean the groove and oiler port (39) in the

bar with the special gauge oﬀ ered as an optional accessory.

Side case (Fig. 36)

Always keep the side case and drive area clean of saw dust and

debris. Periodically apply oil or grease to

this area to protect from

corrosion as some trees contain high levels of acid.

Fuel ﬁ lter (Fig. 37)

Remove the fuel ﬁ lter from the fuel tank and thoroughly wash it in

solvent. After that, push the ﬁ lter into the tank completely.

NOTE

If the ﬁ lter is hard due to dust and dirt,

replace it.

Chain oil ﬁ lter (Fig. 38)

Remove the oil ﬁ lter and thoroughly wash it in solvent.

Cleaning the cylinder ﬁ ns (Fig. 39)

When wood chips are caught between cylinder ﬁ ns (40), the engine

may overheat, resulting in lower output. To avoid this, always keep

cylinder ﬁ ns and fan case clean.

Every

100 operating hours, or once a year (more often if conditions

require), clean ﬁ ns and external surfaces of engine of dust, dirt and

oil deposits which can contribute to improper cooling.

For long-term storage

Drain all fuel from the fuel tank. Start and let engine run until it stops.

Repair any

damage which has resulted from use. Clean the unit with

a clean rag, or the use of high pressure air hose. Put a few drops of

two-cycle engine oil into the cylinder through the spark plug hole,

and spin the engine over several times to distribute oil.

Cover the unit and

store it in a dry area.

CHAIN SHARPENING

Parts of a cutter (Fig. 40, 41)

WARNING

○ Gloves should be used when sharpening chain.

○ Be sure to round oﬀ the front edge to reduce the chance of

kickback or tie-strap breakage.

41. Top plate

42. Working corner

43. Side plate

44. Gullet

45. Heel

46. Chassis

47. Rivet hole

48. Toe

49. Depth gauge

50. Correct angle on top plate

(degree of angle depends on chain

type)

51. Slightly protruding “hook” or point (curve on non-chisel chain)

52. Top of depth gauge at correct height below top plate

53. Front of depth gauge rounded oﬀ

LOWERING DEPTH GAUGES WITH A FILE

1) If you sharpen your cutters with a ﬁ le holder, check

and lower the

depth.

2) Check depth gauges every third sharpening.

3) Place depth gauge tool on cutter. If depth gauge projects, ﬁ le

it level with the top of the tool. Always ﬁ le from the inside of the

chain toward an outside cutter. (Fig. 42)

4) Round oﬀ front corner to

maintain original shape of depth gauge

after using depth gauge tool. Always follow the recommended

depth gauge setting found in the maintenance or operator

manual for your saw. (Fig. 43)

GENERAL INSTRUCTIONS FOR FILING CUTTERS

File (54) cutter on one side of the chain from the inside out. File on

forward stroke only. (Fig. 44)

5) Keep all cutters the same length. (Fig. 45)

6) File enough to remove any damage to cutting edges (side plate

(55) and top plate (56)) of cutter. (Fig. 46)

SHARPENING ANGLES FOR SHARPENING SAW CHAIN

1. Part Number 95VP

2. Pitch .325”

3. Depth Gauge Setting 0.025"

4. Side Plate Filing Angle 85°

5. Top Plate Angle 30°

6. File Guide Angle 10°

Maintenance schedule

Below you will ﬁ nd some general maintenance instructions. For

further information please contact HITACHI dealer.

Daily maintenance

○ Clean the exterior of the unit.

○ Clean the chain oil ﬁ lter port.

○ Clean the groove and oil ﬁ lter port in the guide bar.

○ Clean the side case

of saw dust.

○ Check that the saw chain is sharp.

○ Check that the bar nuts are suﬃ ciently tightened.

○ Make sure that the chain transport guard is undamaged and that

it can be securely ﬁ tted.

○ Check that nuts and screws are suﬃ ciently tightened.

Especially inspect the bolt

of muﬄ er and ensure that they are

properly tightened before starting engine. Should any of the

bolts be loose, retighten them immediately. Failure to do so

could result in serious hazard.

○ Check the tip of the bar. Please exchange it for the new one

when it is worn

out.

○ Check the band of chain brake. Please exchange it for the new

one when it is worn out.

Weekly maintenance

○ Check the starter, especially cord and return spring.

○ Clean the exterior of the spark plug.

○ Remove the spark plug and check the electrode gap. Adjust it to

0.6

mm or change the spark plug.

○ Clean the cooling ﬁ ns on the cylinder and check that the air

intake at the starter is not clogged.

○ Clean the air ﬁ lter.

Monthly maintenance

○ Rinse the fuel tank with gasoline, and clean fuel ﬁ lter.

○ Clean chain oil ﬁ lter.

○ Clean the exterior of

the carburetor and the space around it.

○ Clean the fan and the space around it.

NOTE

When ordering the parts to your nearest dealer, please use the

item numbers showing on the parts breakdown section in this

instruction.

BAR NO.

LENGTH-

TYPE

CHAIN NO.

MODEL NO.

OREGON

107498

105191

104968

105355

13”

15”

16”

18”

95VP-56

95VP-64

95VP-66

95VP-72

000Book_CS40EA_WE.indb 13000Book_CS40EA_WE.indb 13 2010/08/26 10:39:282010/08/26 10:39:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi CS40EA Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info