Bedienungsanleitung Hitachi CS40SB (Seite 9 von 244) (Alle Sprachen)

616683

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

English

STANDARD ACCESSORIES

○ Chain case .................................................................. 1

○ Guide bar ..................................................................... 1

○ Chain ........................................................................... 1

○ Plug clip*...................................................................... 1

○ Chain Saw Oil (100 ml) .................................................1

* Not supplied in certain sales areas.

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES

(SOLD SEPARATELY)

○ Chain Saw Oil

○ Round File

○ Depth Gauge Jointer

Round File and Depth Gauge Jointer are to be used

for sharpening of chain blades. As to its application,

please refer to the item titled “Sharpening of the Chain

Blade”.

○ Chain Case

Always keep the chain cover on the chain while

carrying the chain saw or while storing it.

Optional accessories are subject to change without notice.

APPLICATIONS

General wood cutting.

INSTALLING (REPLACING) SAW

CHAIN

WARNING

○ To prevent accidents, always switch the unit oﬀ , and

disconnect the plug from the receptacle.

○ Don’t use the saw chain or the guide bar other than

those speciﬁ ed in “SPECIFICATIONS”.

CAUTION

Wear gloves and be careful to avoid injury with the saw

chain.

NOTE

○ When removing the saw chain, remove sawdust from

the oil spout, oil hole, and guide bar groove.

If sawdust accumulates, this may cause the unit to fail.

○ Use the correct type of saw chain in accordance with

the speciﬁ cations.

If you install the wrong type of guide bar, the saw chain

may come oﬀ and injury may occur.

1. Removing the side cover (Fig. 4)

1 Rotate the knob once to loosen it.

2 Rotate the tension dial half a turn to loosen it.

3 Turn the knob and remove the side cover.

2. Removing the saw chain and guide bar (Fig. 5)

Remove the saw chain and guide bar in the direction

indicated by the arrow.

3. Engaging the new saw chain in the sprocket

(Figs. 6, 7)

Engage the saw chain at the guide bar tip with attention

to the direction of the saw chain, and then properly

engage the saw chain with the sprocket.

4. Installing the side cover

1 Adjust the tension dial of the side cover so that the

chain tensioner boss is inserted into the guide bar

chain tensioner hole, and attach the side cover. (Fig. 8)

2 Rotate the knob once to temporarily ﬁ x it. (Fig. 9)

5. Adjusting the saw chain tension (Fig. 10)

○ While lifting the guide bar tip, turn the tension dial to

adjust the saw chain tension.

○ Turn the tension dial to the right to increase the saw

chain tension, and to the left to decrease it.

6. Checking the saw chain tension (Fig. 11)

Adjust the saw chain tension so that the gap between

the saw chain drive link and the guide bar is 0.5 to 1 mm

when you lift the saw chain slightly near the center of

the guide bar.

7. Securing the knob (Fig. 12)

1 When adjustment is complete, lift up the guide bar, and

fully tighten the knob.

2 Make sure the bolt is ﬁ rmly tightened.

WARNING

After adjusting the saw chain tension, ensure the knob

is fully tightened.

If it is loose, injury may occur.

INSPECTION AND PREPARATION

PRIOR TO USE

Prior to use, make the following inspection and preparation.

WARNING

○ Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

○ To prevent accidents, always perform steps 1 to 5

ensuring the plug is disconnected from the receptacle.

○ Do not secure the lock-oﬀ button while it is pressed.

If the switch is accidentally engaged, the unit may

unexpectedly start and injury may occur.

1. Ensuring the switch is oﬀ

○ Ensure that the power switch is in the OFF position. If

the plug is connected to a receptacle while the power

switch is in the ON position, the power tool will start

operating immediately, which could cause a serious

accident.

○ When the switch is engaged while pressing the lock-

oﬀ button, the unit switches on, and when the switch is

released, the unit switches oﬀ .

2. Checking the extension cord

When the work area is remote from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short

as practicable.

3. Checking the saw chain tension

○ If the saw chain tension is incorrect, there is a risk of

damage to the saw chain or guide bar and malfunction.

Referring to steps 5 to 7 “Installing (replacing) saw

chain,” ensure an appropriate tension is set.

○ While the saw chain is still new, it is particularly

stretchy, so periodically check the tension and adjust

as required.

○ Also check the knob is securely tightened.

4. Checking operation of chain brake (Fig. 13)

WARNING

○ Although the chain brake is an emergency stop device,

this is not completely reliable. Operate carefully to

avoid the risk of kickback.

○ The chain brake is intended for use in emergencies and

when starting up. Do not use it indiscriminately.

○ To avoid impaired movement of the chain brake due to

buildup of sawdust etc., clean regularly.

○ The chain brake is an important component to ensure

safe use.

If you have any concern regarding the brake operation,

request repair from your Hitachi Authorized Service

Center.

Hitachi CS40SB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info