Bedienungsanleitung Hitachi DH 25 DAL (Seite 8 von 86) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78779

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

English

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically designated

battery packs.

Use of any other battery packs may create a risk

of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach of

children and infirm persons.

CORDLESS ROTARY HAMMER SAFETY

WARNINGS

1. Wear ear protectors.

Exposure to noise can cause hearing loss.

2. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

3. Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature higher than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

4. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

5. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

6. Never disassemble the rechargeable battery and

charger.

7. Never short-circuit the rechargeable battery. Short-

chircuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

8. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

9. When using this unit continuously, the unit may

overheat, leading to damage in the motor and

switch. Please leave it without using it for

approximately 15 minutes.

10. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

11. Using an exhausted battery will damage the

charger.

12. When drilling in wall, floor or ceiling, check for

buried electric power cord, etc.

13. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

14. Wear ear protections

Exposure to noise can cause hearing loss.

15. Do not touch the bit during or immediately after

operation. The bit becomes very hot during

operation and could cause serious burns.

16. Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

17. Always hold the body handle and side handle of

the power tool firmly. Otherwise the counterforce

produced may result in inaccurate and even

dangerous operation.

18. Wear a dust mask

Do not inhale the harmful dusts generated in

drilling or chiseling operation. The dust can

endanger the health of yourself and bystanders.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 and 2 described below, when using

this product, even if you are pulling the switch, the

motor may stop. This is not the trouble but the result

of protection function.

1. When the battery power remaining runs out (The

battery voltage drops to about 14V (DH25DL,

DH25DAL) / about 20V (DH36DL, DH36DAL)), the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

⅜ During work make sure that swarf and dust do

not fall on the battery.

⅜ Make sure that any swarf and dust falling on the

power tool during work do not collect on the

battery.

⅜ Do not store an unused battery in a location

exposed to swarf and dust.

⅜ Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such

as a nail, strike with a hammer, step on, throw

or subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

01Eng_DH25DL_WE 08/4/30, 09:337

Hitachi DH 25 DAL Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info